SpeaKa SP-TVCM-520 Motorized TV Ceiling Mount Instruction Manual
- June 8, 2024
- SpeaKa
Table of Contents
SpeaKa SP-TVCM-520 Motorized TV Ceiling Mount
IN THE BOX
TOOLS REQUIRED
INSTALLATION
Remote Control Operation Instructions
Button Functions
Upward/Downward Movement
- Press the “A” button, the TV mount will move upward to the lowest-profile position against the ceiling.
- Press the “V” button, the TV mount will move downward to the maximum tilt angle position (75° by default).
- Press the “oR button to stop the motion. (Tips: Clear up all obstacles within the range of motion.)
Memory Setting
- Press the emor “mem button for 1 seconds and you will hear a beep, indicating that the current position has been saved to memory. The “mem “mem” buttons can each store a different position.
Recall Memory
- Press the ” ” or “)” button and the mount will automatically get to the position saved in the corresponding button “mem” or “mem”
Reset Mode
- If the TV mount cant be adjusted to the highest position(o degree against the ceiling) or the lowest position max. tilting position), unplug and re-plug the power.
- Then press and hold the “o button for 5 seconds.
- Mount will retract to the highest position, that means the system has been successfully reset.
Reset the Tilt Range for Pitched Ceiling
- The TV mount is 0°-75° adjustable by default. Please reset the tilt range if you use as a pitched ceiling TV mount.
- Prepare: Reset the system (see Instructions on A. Button Functions 4. Reset Mode).
- Step 1: Press “V”A” ande buttons and adjust to the proper position.
- step 2: Press and hold the “memi button until the unit beeps once. Repeat this step5 times. The unit will emit a long beep to indicate success.
Note:
- Step 1, 2 should be finished in 2 minutes, or it will fail to reset.
- Long pressE for 5 seconds to disconnect the device from the app.
- The remote controller is powered by two AA batteries (not included).
Manual Mode
In any position (but the minimum position against the ceiling), when manually push up the TV ceiling mount Over a distance. The TV ceiling mount will automatically return back to the minimum position against the ceiling.
Coding of Remote Controller and Control Box
- Step 1: When the mount is powered on, press the smal button on the control box with a thin tool as shown. The unit emits a beep, indicating that the control box is on standby for program coding.
- Step 2: Press the “E”button on the remote control, and the control box repeatedly beeps for approximate 10 seconds indicating that the remote control is being programmed. The process will be finished automatically until you can’t hear a beep any longer.
IN FRONT
This repair guide intents to help you identify and solve the minor problems caused by unusual operation of the electric system of our electric TV mount. The simple procedures in this manual are easy to follow and capable of solving the most problems happened in everyday use.
Error Indication
The Buzzer Constantly Gives Out Alarm Sound:
- The Error Of Positioning Signal
- Reset the system by following the instruction manual. If the alarm
- SOund continues, please contact us to replace the product.
Remote Control Problems
- Abnormal Loss Of Power
- Normally Batteries Are Out of Power After 24hrs Without Using The Remote Control.) en Please contact us to replace remote control.
- Normally Batteries Are Out of Power After 24hrs Without Using The Remote Control.) en Please contact us to replace remote control.
- Buttons On Remote Control Don’t Work.
- Please check if the batteries have power. If the problem isn’t solved, please contact us to replace the remote control. If the problem is still not solved after the replacement, please contact us to replace the product.
- The Insensitivity Of Remote Control (The Functional Distance Is Less Than 3m.)
- Please replace the batteries. If the problem is still not solved, please contact us to replace remote control.
- Please replace the batteries. If the problem is still not solved, please contact us to replace remote control.
Can’t Operate
Please check if the power adaptor is properly connected to the product. If so, please turn the power on. If there is no buzzer sound or red light power indication, please check if the power adaptor works properly. If the power adaptor doesn’t work please contact us to replace the power adaptor. If the power adaptor works properly, but the TV mount doesn’t work, please contact us to replace the product.
Abnormal Noise
Please contact us to replace the product.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>