Shenzhen Moldull Acoustic Technology MD032 TWS Bluetooth Earbuds User Guide

Shenzhen Moldull Acoustic Technology MD032 TWS Bluetooth Earbuds

Headset Specification

• Transmission distance: 10M
• Battery capacity: 25mAh
• Playing time: about 4 hours (headset)
• Charging time: about 1.5 hours (headset)
• Standby time: about 360 hours

Charging Case Specification

• Battery capacity: 300mAh
• Charging time: about 1.5 hours
• Charging case Can Charge Headset: 5 times

Charging Case Charging

USB CHARGE
Connect the charging case to the USB power adapter with a charging cable, and the voltage must be 5V.

Charging For Headset

Put the headset into the Charge case, and close the top cover.

Connect To Your Phone

1. Settings
2. Find Bluetooth
3. Tum on Bluetooth and search for MD032
4. Click MDO32 ” to connect until”Connected”

Function Diagram

• Power ON
  Open the charging case, Automatically power on

• Answer/ Hung up
  Double-click the sensor position of the headset.

• Next Song
  Triple-click the right headset sensor position.

• Voice Assistant Wake Up
  Keep Pressing the headset touch sensor position for 2.5 seconds

• Clear the pairing information of the connected phone
  Five clicks left-right headphone sensor position

LED Lightguide

The charging case is charging: the white light is on once and the red light is flashing The charging case is fully charged: the red light is always on The charging case is low on power: the white light is flashing Use the charging case to charge the earphones: Open the cover of the charging case, put the left and right earphones into the charging case, the left and right earphones’ red lights are always on, and the lights are off when fully charged (each time the earphones are put into the charging case, the white lights of the charging case turn off for 45 seconds to enter the charging state ).

Function Description

1. Open the cover of the charging case, take out the earphones, the left and right earphones are automatically turned on and paired.
2. When the left and right earphones cannot be connected or the pairing name cannot be searched, it will automatically shut down after 5 minutes; put the left and right earphones into the charging case and close the lid.
3. The headset connected to the Bluetooth device will automatically connect after powering on.
4. The machine has voice prompts.
5. The charging voltage of the charging case is 5V.

Precautions

Since this product uses a small-capacity lithium battery, you must use a regular manufacturer’s charging equipment when charging, and guide charging according to the following precautions:

• Charging voltage: s5V
• Charging current: s500mA

CAUTION: Failure to follow this guide to charge may damage this product; in extreme cases it may even cause an explosion, and may void any warranty on this product.

FCC Caution

This device complies with part 15 of the FCC Rules. Operation is Subject to the following two conditions:1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause unde- sired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to oper ate the equipment.

Note: This equipment has been tested and found to comply with thelimits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>