EYE LIGHTING ELI ConV2 Emergency Pole Mounted LED Luminaire Instruction Manual
- June 4, 2024
- EYE LIGHTING
Table of Contents
ELI ConV2 Emergency
Installation Instructions
Electrical Wiring of the ConV2 Emergency LED Fixture
Option: 3-Phase AC wiring configuration is available upon request.
Important-Safety
This luminaire must be installed by a licensed electrician, following these
installation instructions. Before carrying out any installation or maintenance
on this luminaire, ensure that the main supply is fully isolated. High
voltages greater than the mains voltage can be present during operation.
Any inadequate installation might cause falling, electric shock, fire, or
other hazards.
Ensure only qualified personnel inspect and maintains the luminaire. Excessive build-up of foreign material from outer surfaces should be cleaned to maintain the performance of the luminaire. The battery and light source is non-user replaceable. Contact manufacturer / supplier. Do not modify the luminaire, disassemble or replace any component without confirming with the supplier first. Do not touch the power supply when the luminaire is operating.
If the external flexible cable of the luminaire is damaged, it should only be replaced by the supplier, a service agent or a qualified person.
Emergency Operation Instructions
ConV2 Emergency can operate as maintained and non-maintained emergency mode.
Self-contained Battery
Type: Rechargeable Lithium Iron Phosphate (LiFePO4)
Rated voltage: 12.8 Vdc
Capacity: 6000 mAh
76.8 Wh
Duration (discharge time): >180 min
ta: 60°C max
Charge / input characteristics
| Charge time | ≥16 hours |
|---|---|
| Charge voltage limit | 14.8 Vdc |
Discharge / output characteristics
| Discharge current | 2.0 A max |
|---|---|
| Output voltage / current | 26 – 40 Vdc / 500 mA |
constant current (with load) 50 Vdc (no load)
Output power| 20 W max
Deep discharge protection (V)| 10 ±0.2 Vdc
Battery wiring: Red (+), Black (-)
Caution: do not expose the battery to fire or dispose of it in the fire. Avoid
shorting, excessive physical shock, and vibration.
To guarantee the rated discharge time, please charge the battery for at least
16 hours.
If the luminaire is ever connected to mains voltage before installation (days
or weeks beforehand), the lens cover must be opened following the Access to
internal testing facilities instructions. In the internal gear, the battery
supply connector must be disconnected and reconnected to the Emergency
controller in order to interrupt the discharge cycle, avoiding the Lithium
battery to remain fully discharged for a long period of time. The battery is
supplied 50% charged from the factory.
EYE Lighting Australia Pty Ltd
15 Industrial Avenue
Wacol QLD 4076
For the latest product information visit the EYE Lighting Australia website
Manually operated testing facilities
ConV2 Emergency is supplied with a test switch and a visual LED indicator.
During charging mode, press (down) test switch to replicate emergency mode.
Release the test button to recover charging mode.
Visual LED indicator – green: charging the battery and fully charged. Visual
LED indicator – if the battery is discharging, disconnected, or not being
charged correctly (general malfunction).
A discharge cycle shall be completed at least once every 6 months. Continuous
charging time cannot exceed 6 months.
After installation, the luminaire classification marking on the external label
of the product shall be completed according to AS/NZS 60598.2.22, showing:
TYPE
MODE OF OPERATION
FACILITIES
DURATION OF
EMERGENCY MODE| X: self-contained
0: non-maintained
1: Maintained
A: including test device
B: including remote rest mode
C: including inhibiting mode
D: high-risk task-area luminaire
180 : 3 hours
---|---
Access to internal testing facilities
Only if required to access the test switch remove the lens cover by
unscrewing the 17 x M4 screws. When repositioning the lens cover follow the
tightening sequence and torque for the screws to ensure IP protection.
Please note warranty will not cover any damage due to incorrect tightening
or positioning of the PC lens cover.
Scan for PDF Version
Fixture weight: 5.1 Kg Max.
EYE Lighting Australia Pty Ltd
15 Industrial Avenue
Wacol QLD 4076
For the latest product information visit the EYE Lighting Australia website
Tel: +61 (0) 7 3335 3555
Fax: +61 (0) 7 3335 3533
Email: info@eli.com.au
www.eyelighting.com.au
CONV2EM 27.07.22
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>