DENALI HMT.07.11001 BMW R1250GS Split Instruction Manual

June 9, 2024
DENALI

DENALI HMT.07.11001 BMW R1250GS Split Instruction Manual

DENALI HMT.07.11001 BMW R1250GS Split Instruction
Manual

Thank you for choosing DENALI

We know you would rather be riding your bike than wrenching on it, so we go the extra mile to make sure our instructions are clear and as easy to understand as possible. If you have any questions, comments, or suggestions don’t hesitate to give our gear experts a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COM

Please Read Before Installing

DENALI products should always be installed by a qualified motorcycle technician. If you are unsure of your ability to properly install a product, please have the product installed by your local motorcycle dealer. DENALI takes no responsibility for damages caused by improper installation. Caution : When installing electronics it is extremely important to pay close attention to how wires are routed, especially when mounting products to the front fender, front forks, or fairing of your motorcycle. Always be sure to turn the handlebars fully left, fully right, and fully compress the suspension to ensure the wires will not bind and have enough slack for your motorcycle to operate properly.

Installation Tips

We strongly recommend using medium strength liquid thread locker on all screws, nuts, and bolts. It is also important to ensure that all hardware is tightened to the proper torque specifications as listed in your owner’s manual. For included accessory hardware please refer to the default torque specifications provided below. Inspect all hardware after the first 30 miles to ensure proper torque specifications are maintained.

DENALI HMT.07.11001 BMW R1250GS Split - Installation
Tips

Hardware Sizing Guide

Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc. Remember, the length of a screw or bolt is measured from the start of the “mounting surface” to the end of the screw, so only include the screw head when measuring countersunk screws.

DENALI HMT.07.11001 BMW R1250GS Split - Hardware Sizing
Guide

What’s In The Box?

DENALI HMT.07.11001 BMW R1250GS Split - Overview

Kit Contents

(a) M8x75mm – SocketHead Screw……………………………………….Qty 2
(b) M8 Washer………………………………………………………………..Qty 2
(c) Acoustic Horn Bracket……(HMT.07.014)…………………………….Qty 1
(d) M8 Spacer…OD 19.05mm, ID 8.1mm, L 19.05mm………………..Qty 2
(e) M6x30mm – Socket Head Screw………………………………………Qty 2
(g) M6 Washer………………………………………………………………..Qty 2
(g) Compressor Mount …..(HMT.07.013)………………………………..Qty 2

Compatibility : SoundBomb Split Horn

Tools Required: 6mm Allen Key, 5mm Allen Key

Installing The Compressor

DENALI HMT.07.11001 BMW R1250GS Split - Installing The
Compressor

1.3 – Installing The Compressor

Step One : Install the hose end onto the compressor, making sure it is all the way on and secure.
Step Two : Use the horn provided hardware (M8 Hex bolt, M8 Nut) and a 13mm wrench to secure the compressor to the Bracket (g).
Step Three : Locate both of the mounting points on the engine case on the left hand side of the bike and remove the factory bolts.
Step Four : Mount the Compressor Bracket (g) and compressor to the mounting locations using the two M6x30mm screws (e) and two M6 Washers (f).
Step Five : Route the hose down the left side and underneath the bottom of the compressor, then wedge it in the gap between the right side of the compressor and the bracket. The remainder of the hose should be channeled up under the side fairing and forward through towards the front shock. Once through to the front, the hose end should be routed up behind the steering head through the tubular frame sideways towards the right side where it can be connected to the acoustic unit.
Step Six : Route the horn wiring harness down into the same channel between the right side of the compressor and the bracket where the hose is wedged. Connect the wire leads to the bottom of the compressor when ready.

Installing The Acoustic Unit

DENALI HMT.07.11001 BMW R1250GS Split - Installing The Acoustic
Unit

1.1 – Installing the Acoustic Unit

Step One : Start by removing the upper M8 mounting bolt from the right side of the upper fairing stay. Do not remove the lower bolt yet.
Step Two : Using the M8x75 Socket head (a), M8 Washer (b), and M8 Spacer (d) secure the top hole of Acoustic Bracket (c) to the upper mounting hole on the fairing stay and hand tighten with a 6mm allen.
Step Three : Rotate the bracket (c) counterclockwise until there is clearance to remove the lower factory mounting bolt. Next reposition the bracket and secure it to the lower mounting location with the remaining M8x75mm bolt (a), M8 Washer (b) , and M8 Spacer (d). Properly tighten both bolts.
Step Four : Take the remaining end of the hose and install it onto the top of the acoustic unit, firmly press down to make sure it is all the way on and secure.
Step Five: Mount the acoustic unit to the installed bracket-A using the horn’s included hardware (M6 Hex Bolt, dampener, M6 nut) and a 10mm wrench.
NOTE : The hex head should be slid all the way up to the top of the slot.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

DENALI User Manuals

Related Manuals