SPEEDIANCE S1 Personal All-in-One Home Gym Monster User Manual
- June 5, 2024
- SPEEDIANCE
Table of Contents
Product Manual
Safety Warning
indicates “prohibitions”
- When removing the plug, do not pull the power cord, and instead, hold the plug firmly and pull it out directly from the socket. For the sake of user safety, please prevent the power cord from being damaged, and if the power cord is damaged or the plug is worn, stop using the product. If the power cord is worn or damaged, please get it replaced at the service station designated by the manufacturer.
- Neither disassemble nor modify electronic elements such as circuit boards without permission nor damage them. Please get the product maintained by professional maintenance personnel. If the power cord is damaged, please get it replaced by the manufacturer, its maintenance department, and professional maintenance personnel to avoid danger.
indicates “musts”
- Please use the standard three-pin power socket with a rated current above 10A, and do not share it with other electrical appliances. Keep the power plug in good contact with the socket, otherwise, it may lead to fire hazards. Please ensure that the grounding electrode of the socket has a reliable grounding wire.
- This product is to be supplied by 100-240V~50-60Hz AC power, and if the voltage fluctuation exceeds the specified range, it will lead to product failure or damage. Under such a circumstance, an automatic voltage regulator above 1600W should be equipped for utilization.
- When flammable gas (such as gas) leaks, close the leaking valve, open the doors and windows, and do not pull out the plugs of the product and other electrical appliances, as an electric spark may occur and cause fire at this time.
- Do not use flammables, explosives, liquid, and corrosives near the product to avoid product damage or fire accident. Do not place or use combustibles near the product to prevent a conflagration.
- When discarding the product, please send it to the designated recycling station for disposal to keep it away from children and accidents.
- Place the product in an open area without any obstacles around.
- Do not clean the product by water spraying or rinsing, and do not place the product in a damp place or a place in which it can be splashed with water, so as to guarantee the indicates “notices” that may cause minor injuries or property losses
- For the sake of safety, it is recommended not to place other items than those recommended by the supplier on the product.
- After use, make sure that the product is off or on standby, and do not stretch your hand out into the small gap to avoid finger pinching. Release the accessories as gently as possible to avoid injury.
- To avoid unexpected accidents, prevent the children from accessing the product, pulling wires, handles, and other mechanical structures, or operating the power button without the attendance of an adult.
- When folding the footboard, ensure the footboard is folded in the correct position and locked, so as to prevent personal injury or other property loss when it drops down caused by improper locking.
- In case of power failure or cleaning, remove the power plug, and if the power supply is to be connected again, wait for 5 minutes at least to prevent motor damage or other electronic component damage resulting in continuous starting-ups.
Product Overview
Diagram of product accessories
- Support arm
- Display
- Lifting slider
- Connector
- Motor compartment hatch
- Lock handle
- Footboard
Diagram of product accessories
First use
Before first use, remove all packaging materials including the outer carton,
PE foam, gummed paper bag, etc., and tear off the protective film on the
product, if any.
Place the product in an indoor well-ventilated place with flat and solid
ground
Keep the product away from heat sources and prevent it from being exposed to
direct sunlight. Do not place it in wet or watery places, so as to prevent
rust or degradation of insulation effect.
Considerations for placement
- Be sure to place the product on the ground, with an open space reserved above its top, a distance of more than 15cm reserved between its back and the wall, and no other obstructions on both sides of the product.
- Except for the rear side, reserve an open space in front, on left and right, and above the top of the product to facilitate normal use and avoid injury.
- Place the product in a dry environment, and do not use it outdoors.
Power supply connection and power-on
- After the product is turned on with power supply connections for the first time, rest it for 5-10 min to check the product for appearance defects or unusual operating noise, and if any abnormality is found, turn off the power supply, and contact the after-sales service personnel.
- After power-on, verify that the environment around the product meets the use standard, and the footboard is flat without tilting.
- After the above inspections and confirmations can the product be used.
User registration
- Check that all the required information is shown completely on the display, and the touch function of the screen is normal.
- After function confirmation can the strength training be carried out according to your needs.
Moving pulley block
Replacing accessories
- The connector is compatible with all accessories (including handle, leg shackle, double-headed rope, barbell, etc.).
- If the connector becomes loose, stop using the product immediately and contact the after-sales service personnel of SPEEDIANCE for treatment.
Unlocking pulley block
Folding/unfolding footboard
- The operation logic for unfolding and folding of the footboard is the same
- Before unfolding the footboard, always check that there are no other objects in the unfolding area, so as to avoid potential safety hazards due to an uneven footboard.
- After the footboard is folded, confirm that the indexing pin has been locked, so as to avoid accident and property damage when the footboard drops down unexpectedly.
Operation Method
Smart handle
-
Check if the two smart handles involve appearance defects, and check if they function normally after power-on.
-
Connect the two handles to the main unit through connectors. (For details of connection method, refer to P10 “Replacing accessories”)
-
Press the button at either end of the handle (as shown on the right) for Bluetooth pairing, and wait for the pairing to be completed.
-
After the configuration is completed can the course learning and training be started.
Double-headed rope
- Check the double-headed rope for damage, and if any, stop using the product, and contact the after-sales service personnel of SPEEDIANCE.
- Connect the double-headed rope to the main unit through the connector. (For details of connection method, refer to P10″Replacing accessories”)
- After the installation is completed can the course learning and training be started?
Leg shackle
- Check the two-leg shackles for damage, and if any, stop using the product, and contact the after-sales service personnel of SPEEDIANCE.
- Open the leg shackle and put it on the ankle, pass one end of the leg shackle through a D-shaped ring and fix it with a hook and loop.
- Connect the double-headed rope to the main unit through the connector. (For details of connection method, refer to P4 “Replacing accessories”)
Barbell
- Check the barbell for damage, and if any, stop using the product, and contact the after-sales service personnel of SPEEDIANCE.
- Connect the barbell to the main unit through the connector. (For details of the connection method, refer to P4 “Replacing accessories”.)
- After the installation is completed can the course learning and training be started?
Barbell controller
-
Check the barbell and its controller for damage, and if any, stop using the product and contact the after-sales service personnel of SPEEDIANCE.
-
Connect the barbell to the main unit through the connector. (For details of the connection method, refer to P4 “Replacing accessories”.)
-
Clamp the controller in the appropriate place on the barbell. (Adjust the controller to the appropriate angle through translation and rotation for the convenience of use.)
-
Press and hold “Pause ” button to activate Bluetooth for pairing, and wait for pairing to be completed.
-
After the configuration is completed can the course learning and training be started?
If there are problems still unsolved, please call the customer service hotline of SPEEDIANCE
Parameters and Maintenance
Parameters
Notice
The parameters given in this table are for reference only, and in the case of
any conflict with the data on the nameplate of the product, the data on the
nameplate shall apply.
Parameters of main unit
| Name | GYM MONSTER S1 |
|---|---|
| Overall dimensions (unfolded) | 12407101845mm |
| Overall dimensions (folded) | 3207101845mm |
| Weight | 85KG |
| Resolution | 1920*1080 |
| Rated current | 16A |
| Rated power | 1600W |
| Noise | 65dB |
| Bluetooth | BT5.0 |
| Accessories | Smart handle * 2, barbell, controller, Triceps Pull Down Rope, |
Ankle Strap * 2
Wi-Fi| WIFI 802.11b/g/n
Cleaning and maintenance
Notice
This section describes the safety precautions and their importance to prevent
personal injury or property damage to users or others. Please read the text
with a full understanding of the following (signs, pictograms), and be sure to
follow the safety precautions described below.
Notice
Before cleaning the product, please remove the power plug.
Cleaning
- Please clean up the dust on the back of the product and on the ground as scheduled to improve the heat dissipation effect and save energy.
- When cleaning the product, please use a soft towel or sponge dipped in clear water or non-corrosive neutral detergent, and finally wipe it with clean water and dry it with a dry cloth. After cleaning, do not turn on the power supply until the product is naturally dried.
- During cleaning, prevent water droplets from flowing into the gaps of the product, otherwise, short circuit or electrical element burning may occur.
- When cleaning accessories, please use a soft towel or sponge dipped in clear water or non-corrosive neutral detergent, and finally wipe it with clean water and dry it with a dry cloth. After cleaning, do not use the accessory until it is naturally dried.
Warning
Do not use hard brushes, steel wools, steel brushes, abrasive compounds (such
as toothpaste), organic solvents (such as alcohol, acetone, banana oil, etc.),
boiled water, and acid and alkaline substances to clean the product.
Otherwise, the surface of the product will be damaged.
Notice
Do not rinse the product with water, otherwise, the electrical insulation
performance will be affected.
- When the product is to be out of use for a long time: remove the power plug to avoid electric shock or fire due to the aging of the power cord.
Common Faults and Troubleshooting
Treatment of problems other than faults
Notice
If no fault is identified after inspection but the product still malfunctions,
please cut off the power supply and contact the after-sales service personnel
of SPEEDIANCE.
Troubleshooting of Common Faults
| Symptoms | Possible cause(s) | Solution(s) |
|---|---|---|
| Mainframe not working | •Power cord disconnected or power plug not fully |
inserted
•Low voltage, power outage or partial power cut.| •Firmly insert the power
plug
•Ask professional electricity maintenance personnel for help
Heavy motor noise| •Uneven ground
•The product is not placed evenly| •Race the product on even ground
•Remove objects in contact with the iv product
Uneven step board| •Uneven ground
•The product is not placed evenly| •Place the product on even ground
•Remove objects in contact with the product
Fans working after the product is turned off| •A too high 100M temperature
requires more dissipation time
•High temperature after usage| •This is a normal situation. Let it be.
WO b b le| •Uneven ground
•Unlocked or half-locked step board| •Place the product on even ground
•Push the quick release lever to the lowest level for complete lock-in
Trouble folding/unfolding the step board| •: Articles around the pivot
•, Lkedstepboard| •Remove the objects in question
•Unlock the step board according to the manual
Accessories not working| •Running out of battery| •Replace the battery
High temperature of
motor compartment| •High room temperature Long time usage| •This is a normal
situation. Place the
•product somewhere ventilated.
Trouble removing the pulley set| •Locked. in pulley set
•Still working motors| •Unlock the pulley set according to the manual
•Pause the motors by pressing the buttons on accessories or touchscreen
Warranty and Service
Warranty scope
Notice
The warranty starts on the date that the product is purchased and is valid for
24 months for the machine and 12 months for accessories. The customer must
provide valid proof of purchase for warranty. Replacement parts are available
for sale after the warranty period is over.
Warranty service will not be provided for the parts as:
- Damage caused by improper use, improper maintenance, or improper storage and force majeure.
- Normal wear and tear.
- Damage caused by unauthorized repairs of the product.
- Re-sold / second-hand items.
You can apply for our product warranty service if there is a performance
failure during the valid warranty period, please send an email to
service@speediance.com, we will get back to
you as quickly as possible.
If there is a quality issue, please contact us within 7 calendar days of
receiving your product.
- Contact email service@speediance.com with the following information.
- Order Number:
- product issue:
- Images or Videos of Products and Intact Packaging:
We will process your inquiry within two working days after receiving your email.
Return & Refund Service will not be provided where:
- It is requested beyond 7 calendar days of receiving a product.
- A product sent to Speediance for Return & Refund Service does not include all original accessories, attachments, packaging, or any item is not in new or like-new condition, i.e. with damages.
- Legal proof of purchase, receipt, or invoice is not provided or is reasonably believed to have been forged or tampered with.
- Any fault or damage of the product is caused by unauthorized use or modification of the product, including exposure to moisture, entry of foreign materials (water, soil, sand, etc.), or improper installation or operation.
- Product labels, serial numbers, waterproof marks, etc. show signs of tampering or alteration.
- Damage is caused to the product by uncontrollable external factors, including fire, floods, high winds, or lightning strikes.
- A product is not delivered to Speediance within 7 calendar days after Return & Refund Service confirmation is sent from Speediance.
- Other circumstances not stated in this policy where applicable.
Refund Time
Refunds will be processed using the same method that was used to make the
payment. The refund process will be completed in about 7-14 business days,
depending on the bank or credit card issuer.
Return Shipping
Customers need to pay for any return shipping to the designated service center
(including cross-border and international shipping costs, if applicable)
unless the return is caused by performance faults.
Replacement Fee
Speediance shall be responsible for the two-way replacement freight for any
products sent in for replacement due to performance faults. Or the customer
shall be responsible for the two-way replacement freight for any products sent
in for replacement when the warranty period has expired.
Do not return any Product without first receiving a Return Material Authorization (RMA) number provided by Speediance and instructions for how to proceed.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:(1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
For Interactive Multi-Media Digital Fitness Equipment This device complies
with RF radiation exposure limits set forth for an uncontrolled environment.
This device should be installed and operated with a minimum distance of 20 cm
between the radiator and your body.
For the Barbell controller and Smart handle The device has been evaluated to
meet general RF exposure requirements. The device can be used installed and
operated with a minimum distance of 0 mm between the radiator and your body.
IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause int reference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
service@speediance.com
Address: 8A-F, Konka R&D Building, No. 28, South 12th Road,
Science and Technology Park, Nanshan District, Shenzhen,
Guangdong province, China Zipcode: 518000
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>