AKOYU M5371+F22 Wireless Doorbell User Manual
- June 9, 2024
- AKOYU
Table of Contents
Wireless Doorbell
User Manual
M5371+F22
Safety
Before proceeding with the installation, please note the following safety
warnings:
Always follow the manufacturer’s advice when using power tools and wear
suitable protective equipment when drilling holes, etc.
Before drilling holes in walls, check and hidden electricity cables and water
pipes. The use of a cable/pipe locator is advisable if in doub.
What You Should Know Before Installation
- Test the operating range you desire. Choosean electric outlet at the height of 3.3 feet atleast and plug in the receive and take the button outside the door to test if it can work well within the range you have chosen.
- Set a desired music (different or same one) for transmitters before installation. Doorbells have been paired and set to a default chime (Ding Dong) before leaving factory.
- Please do not install transmitter on metal doors since it is hard for the signal to transmit.
- Please take out the battery insulating strip before using if have. ((As picture①
- Ensure all surfaces are clean by wiping the installation area with a clean cloth. Please note that the sticker will have poor adhesion if you attach it to a dirty or uneven surface. Sunlight or rain will also affect the adhesion over a longer period of time.
Product Structure Diagram
- LED Light
- Music Control
- Volumn Control
- Plug
- Speaker
① Led Indicator
② Push Button
Set up and Operation
Press the push button to test whether it is paired with the doorbell. The doorbell will lightup and ring. If it does not, see “Connect a PushButton” on page?
-
Adjust the Volume
• Press the【 】to adjust the volume. {when the power is cut off, and power is restored again, the volume will be.iutomatically adjusted to m.iximum)
• At the maximum and minimum volume, the door bell will sound “didi” twice
• There are total 5 levels including the mute mode. -
Change the Tune
Press the【 】【 】to loop tones
3. Connect a Push Button
You can connect up to 20 accessories to your doorbell, including other push buttons, windowor door opening sensors, and motion sensors.
(1) VARIABLE- Tone Pairing
- Plug-in the receiver, pressing and holding the【 】 on the receiver for 5s, the receiver will beeps once, which means receiver get into pairing mode.
Long Press【 】Ss
- Pess push button, the receiver will beeps twice with LED indicator flashes ls.
- Press push button again, the receiver will beeps once with LED indicator flashes ls, which means the pairing is successful.
- Short press【 】or leave it 20s without any operation, the doorbell will exit the pairing mode.
Notice: Adding the additional push buttons or receivers please according to the above steps.
(2)Fixed- Tone Pairing (Only play your saved tone)
- Select a tone that you like
- Pressing and holding【▽】&【△】button together for about 5s until the receiver beeps once, which means receiver get into pairing mode.
- Press push button once, the receiver will beep twice with LED indicator flashes ls.
- Press push button once again, the receiver will beeps once with LED indicator flashes 1s,which means the pairing is successful
- Short press 【 】or leave it 20s without anyoperation, the doorbell will exit the pairing mode.
Notice: Pair and set only one transmitter at a time to avoid interference
and ensure successful operation.
4. Delete a Push Button
Plug-in the receiver, pressing and holding the【 】on the receiver for 5s,
the receiver will beeps once, which means receiver get into pairing mode.
Long Press【 】Ss
- Pressing and holding the 【 】AGAIN for Ss, the receiver will beeps 4 times, LED flashes 4 times, which means all push button deleted.
5. Reset (Clearing out Settings)
To return all settings to their default settings. Hold down【 】and plug it into
an outlet. After playing the beep 9 times slowly and beep 6 times fast , all
settings will return to factory defaults.
Installation
Choose a location that is not near a heat source or on something that moves (like a door). For non-mounting locations, choose a place where the doorbell will be easy to see and hear.
-
For Receiver:
Plug-in receiver: Just plug receiver into standard outlet in room. -
For Push button: IMPORTANT:
• Before installation, please test if the operating range you choose is working and set music if needed.
• Before you drill any hole in the wall, please make sure there are not cables or pipes
• To install you will require a drill and cross-head-ed screwdriver.
A. Open the Transmitter with screw driver and separate the front cover from
the back cover. Penetrate the two standby holes at the back cover with two
screws.
Then fix the screws on the wall at sultable height.
B. Or you can stick the Transmitter with the double-sided adhesive tape.
C. If you are not mounting the push button to the wall, place it where you
want it
Battery Replacement of Push Button
Open the battery cover and install the CR2032 battery
Specifications
| Doorbell| Push Button
---|---|---
Push Button Temperature| -4°F to 140°F| -4°F to 140°F
Radio Frequency| 433.92 MHz| 433.92 MHz
Range (open field)| 1,000 ft| 1,000 ft
Sound Level (typical)| 0-120 dB| –
Battery Type| Plug in| CR2032
Battery Life(5 activations/day)| Up to 5 years| Up to 3 years
Rain Proof| N/A| Ip55
Trouble shootings
| if | Then |
|---|---|
| The doorbell does not work | 1. The doorbell might be out of range; try the |
doorbellin a different location
2. Reconnect the doorbell. See “Connect a Push Button on page 5.
3.Check all the batteries and replace if needed
4.Check if the LED on the transmitters is working when activated.
5.Check if the doorbell is muted. Check that the transmitter is linked with
the chime
Range is reduced| 1. Metal structures including uPVC door frames can reduce
the range
Don’t mount the the doorbell or doorbell I push on or near metal structures
2. Move the doorbell closer to the doorbell push button.
Weak batteries will reduce range.
In cold conditions (below 5ºC), batteries may need to be replaced more often.
1 Year Limited Warranty
This product is warrnnted to the original purchaser only for a period of 1
year from the date of purchase for products damaged due to defect in
workmanship and materials. Proof of purchase is required to obtain warranty
service. Warranty is for replacement only. No service parts are available for
these products. No other warranties are expressed or implied. Batteries are
not covered under this warranty.
FCC Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly
approved by the party.
Responsible for compliance could void the user’s authority to operate this
equipment. (Example- use only shielded interface cables when connecting to
computer or peripheral devices).
This equipment complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
The equipment complies with FCC Radiation exposure limits set forth for
uncontrolled enviroment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
For warranty and after sales service, please contact
AKOYU Customer Service by
email: akoyuteam@l63.com
Documents / Resources
|
AKOYU M5371+F22 Wireless
Doorbell
[pdf] User Manual
F22, 2AZI3-F22, 2AZI3F22, M5371 F22 Wireless Doorbell, Wireless Doorbell,
M5371 F22 Doorbell, Doorbell
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>