AKOYU ZD51+RC531 Bike Alarm Instruction Manual

Bike Alarm
Instruction Manual
ZD51+RC531

Product Description

Features

• 7 Levels of Adjustable Vibration Sensitivity
• Wireless Remote Control
• 2 Kinds of Light Flashing
• 3-level Adjustable Volume
• Tilt Alarm Function
• Low Battery Warning

How to Switch On/Off:

To load 3*AAA batteries (Included), the device switches on automatically, at the same time the red-light quick flashing with a “di” sound. Unload the batteries, it switches off automatically.

How to Set Arm/Disarm Mode:

There are 2 ways:

1. Short press settings key on the back:
   Loosen the screw at the bottom, take out the back cover, short press the Settings key to switch the armed or disarmed status.
   First: Loosen the screw at the bottom
   Second: Pry the back cover from the pry hole and take the cover down
   Short press the Settings key to switch the armed or disarmed status
   Arming:
   With a “di” sound and a flash, after 5 seconds delay, there is another “di” sound and a flash, shows that it is arming now. When the vibration is triggered, the LED light will flash quickly and an alarm sound will be heard at the same time.
   Disarming: with two “di” sounds and two flashes, it is called disarming.

2. Remote Control to set arm/disarm mode: Short press the “arming key” on the remote to set arm/disarm mode as below:
   Also, to set the volume, mute mode & emergency call with another 2 buttons as below:
   

How to Set LED Mode & Standby Mode:

1. Set to DISARMED mode first.
First: Short press the Settings key to switch into the disarmed state
2. Short press Mode Button on the front to switch LED mode and standby mode
Second: Short press Mode Button on the front to switch LED mode and standby mode
Flashing Mode: LED light keeps flashing, no alerts even when a vibration is triggered
LED Always on Mode: LED light is always on, no alerts even when a vibration is triggered
Standby Mode: t he light is off during the standby mode with a “di” sound. Then set arm mode with remote, the light will flash quickly when a vibration is triggered, and alarm sound will be released at the same moment.

Notice:

• Under ARMED status, this button doesn’t work, cannot set LED mode neither.

How to Match/Delete Remote Control:

How to Match:

1. Set to STANDBY mode first
   First: Short press the Mode key to switch into the Standby mode

2. Long press the Settings key on the back with “di” sound and LED light always—on, it means the device is ready to match;
   Second: Long press the Settings key to get into matching status

3. Then press any key on remote, it comes “di” sounds twice, the matching is successful. when it comes three times “di” sounds, the device can’t match any more remotes Third: A matching signal will be delivered when any key on the remote control is pressed

4. While matching, short press any key or no operation for a long time will exit the matching status.

How to Delete:

1. Under the matching status.
2. Long press the Settings key on the back and heard “di” sounds five times, it means it has deleted all the remotes.

Notice:

• One device can match up to 20 remotes.
• If the device is under LED Always on mode or Flashing mode, any press on the remotes will switch it into standby mode

How to Set 1-7 vibration sensitivity:

1. Set the device to DISARM mode
   First: Short press the Settings key to switch into the disarmed state

2. Long press the Settings key and the Front Mode key at the same time. The red light is on and with seven times “di” sounds, it shows that the device is currently at the top sensitivity level 7.
   Second: Long press the Mode key and the Settings key simultaneously to adjust vibration sensitivity

3. Then short press the Front Mode key, one “di” sound indicates it is in level 1 sensitivity. Continue to short press the Mode key, and two “di” sounds indicate it goes on level 2 sensitivity there are a total of 7 levels of sensitivity which can be adjusted.
   Third: Short press the Mode key to adjust 7 levels of vibration

4. After finish setting the sensitivity, short press the Setting key on the back or no operation for a long time will exit the sensitivity adjusting status.

How to Turn on/off Tilt Alarm:

How to turn on tilt alarm:

1. Set the device to DISARM mode and choose an installation angle. (Take horizontal placement as an example)
   First: Short press the Settings key to switch into the disarmed state

2. Short press the Front Mode key, switch to LED Always on mode.
   Second: Short press Front Mode key to LED Always on mode

3. Long press the Mode key and heard a “di” sound, which implies the tilt alarm function turns on.
   Third: Long press the Mode key and a “di” sound implies the tilt alarm function is on

4. Set back to STANDBY mode, when the device is tilted more than 45 degrees from the current angle, it will begin to make “didididi” alerts; if the tilt angle continues to be greater than 45 degrees, it will alarm every 30 seconds until the tilt angle is less than 45 degrees.
   When the device is tilted more than 45 degrees from the original angle, it will begin to alert

How to turn off tilt alarm:

1. Set the device to DISARM mode.
   First: Short press the Settings key to switch into the disarmed state

2. Short press the Front Mode key, switch to LED Always on mode.
   Second: Short press the Front Mode key, switch to LED Always on mode.

3. Long press the Front Mode key and heard “di” sounds twice, means the tilt alarm function is turned off.
   Third: Long press the Front Mode key and heard “di” sounds twice, means the tilt alarm function is turned off

How to Reset Device:

1. Unload the batteries.
2. Keep long pressing the Front Mode key until finishing load the batteries with red light always on and ten slow “di” sounds, final four quick “di” sounds ending.
3. The device is reset successfully, which means all accessories and settings are deleted and the alarm is back to disarmed state
   Keep long pressing the Front Mode key until finishing load the batteries with red light always on and ten slow “di” sounds, final four quick “di” sounds ending

Low Battery Warning:

The device will alarm once in every 30-35 seconds with “dididi” sounds, when the voltage is lower than 3.3V.

Installation Methods

Bracket Installation
Tie Installation

Technical parameters

Operating voltage: 3 AAA batteries
Standby consumption: <1 ma
Alarming consumption: <50ma
Wireless distance: >100m
Radio frequency: 433.92 MHz
Alarm decibel: 120 dB

Contact Information

Please feel free to contact us by below email, if you have any questions:
AKOYUTEAM@163.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>