BALTECH RFID Card Reader User Manual
- June 9, 2024
- BALTECH
Table of Contents
Operation Manual
RFID Reader
Covered Variants:M/N: 12115-1
RFID Card Reader
The “12115-100” Reader/Writer is a desktop contactless smart card USB Smart card reader and writer with the high frequency card technology. It supports Mifare, ISO 14443A/B and ISO 15693 standards transponders.Based on BALTECH’s core technology it provides support of the latest smartcard technologies, encryption and security features.
Mounting and Connection
The reader generates magnetic field at 13.56MHz which could be influenced by
any electrically conductive material close to the device.
To ensure good performances and functionalities in terms of read range and
reliability a minimum distance of 10cm from such materials is required.
Mounting the unit directly to metal would result in a severe reduction of read
range down to zero functionality. Care should be taken when testing the device
after mounting at a problematic environment: Read ranges and performance vary
from card to card and very much from card to tag or key-fob.
When mounting multiple readers, the distance between readers should be minimum
0.5 m in order to avoid degradation of performance due to interference.
To connect the device to a host system (a printer or a PC), please make sure
that the system provides an USB socket intended for connection of the reader.
Operation
Whenever the device is connected to a proper power supply, it will switch on the internal antenna and periodically scan for a card. Once a card has been detected, the card number is read, the data converted and sent to the host system through the USB Interface. To enable the device to read cards, tags and key-fobs successfully, they should be placed centred above the reader. The device is used for identification, access control.
Technical Features
| Operating Frequency | • 13.56MHz |
|---|---|
| Data transmission modulation reader to card: | ASK |
| Data transmission modulation card to reader: | AM/Load modulation |
| Interfaces | USB: Full speed 2.0 |
| Contactless Card | Supported standards: ISO14443 A & B, ISO15693, |
Communication speed ISO14443A/B: Baud rate up to 424kBaud
Operating Range| • ISO14443A/B: up to 5cm
• ISO15693: up to 8cm
Human| Red, Green, Blue LEDs & Buzzer
Supply Power [VDC]| +5V (±5%)
Power Consumption [W]| Up to 1.5 / 1 typ.
Operating Temperature [°C]| -20 to +65
Operating Humidity [%]| 20 to 80 relative humidity; non-condensing
Non-Operating Humidity [%]| 10 to 90 relative humidity; non-condensing
Antennas| • 13.56MHz integrates PCB loop antenna
Duty cycle for normal use operation [ 6 minutes timewindow]| Use 1 time within
6 minutes. An interaction with the user is 10 seconds in the vicinity to the
device.
• Duty Cycle = (1 x 10s )/ 6 min = 2,78 %
Pinning
The reader supports USB host interface.
USB Interface Molex Header (4 pins)
Molex Part Number: 53261-0471
| Pin# | Name | Type | Description |
|---|---|---|---|
| 1 | PWR | Power | 5V Power Supply |
| 2 | D- | Data | USB-Data inverted |
| 3 | D+ | Data | USB-Data |
| 4 | GND | Power | Signal and Power Ground |
**General regulatory requirements for 12115-100
**
FCC ID: OKY12115100A01A
IC : 7657A-12115100
PMN : RF1060R
NOTICE:
This device complies with Part 15 of the FCC Rules and with Industry Canada
licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Changes or modifications made to this equipment not expressly approved by
BALTECH AG may void the FCC authorization to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
BALTECH AG
Lilienthalstraße 27
85399 Hallbergmoos
Germany
Phone: +49 (811) 99 88 1- 0
FAX: +49 (811) 99 88 1- 11
e-mail: info@baltech.de
http://www.baltech.de/
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>