BALTECH 12117810A01A RFID Reader User Manual
- June 3, 2024
- BALTECH
Table of Contents
BALTECH 12117810A01A RFID Reader
INTRODUCTION
The “12117-XYZ” Reader/Writer is a desktop contactless smart card USB & Bluetooth wireless Technology Smart card reader and writer combining the high- and low frequency card technologies. It supports Mifare, ISO 14443A/B and ISO 15693 standards as well as all major 125kHz-based transponders. Optional it has also RS232 interface. Based on BALTECH’s core technology it provides support of the latest smartcard technologies, encryption and security features.
Mounting and Connection
The reader generates magnetic field at 13.56MHz, 125 KHz and 2.4 GHz which could be influenced by any electrically conductive material close to the device. To ensure good performances and functionalities in terms of read range and reliability a minimum distance of 10cm from such materials is required. Mounting the unit directly to metal would result in a severe reduction of read range down to zero functionality. Care should be taken when testing the device after mounting at a problematic environment: Read ranges and performance vary from card to card and very much from card to tag or key-fob. When mounting multiple readers, the distance between readers should be minimum 0.5 m in order to avoid degradation of performance due to interference. To connect the device to a host system (a printer or a PC), please make sure that the system provides an USB socket intended for connection of the reader.
Operation
Whenever the device is connected to a proper power supply, it will switch on the internal antenna and periodically scan for a card. Once a card has been detected, the card number is read, the data converted and sent to the host system through the USB/RS232(model-dependent) Interface. To enable the device to read cards, tags and key-fobs successfully, they should be placed centred above the reader. The device is used for identification, access control.
Technical Features
Operating Frequency| · 0.125MHz
· 13.56MHz
· 2402MHz-2480MHz
---|---
Data transmission modulation reader to card:| ASK
Data transmission modulation card to reader:| AM/Load modulation
Interfaces| USB: Full speed 2.0, RS 232, Bluetooth 5.2
Contactless Card| Supported standards: LEGIC, ISO14443 A & B, ISO15693,
Communication speed ISO14443A/B: Baud rate up to 424kBaud
Operating Range| · ISO14443A/B: up to 5cm
· ISO15693: up to 8cm
· 125kHz: up to 6cm
· Bluetooth wireless technology: up to 10m
Human| Red, Green, Blue LEDs & Buzzer
Supply Power [VDC]| +5V (±5%)
Power Consumption [W]| Up to 1.5 / 1 typ.
Operating Temperature [°C]| -20 to +65
Operating Humidity [%]| 20 to 80 relative humidity; non-condensing
Non-Operating Humidity [%]| 10 to 90 relative humidity; non-condensing
Antennas| · 2.4GHz internal Chip antenna
· 125kHz permanently attached coil antenna
· 13.56MHz integrates PCB loop antenna
Duty cycle for normal use operation [ 6 minutes time window]| Use 1 time
within 6 minutes.
An interaction with the user is 10 seconds in the vicinity to the device.
**** ·Duty Cycle = (1 x 10s )/ 6 min = 2,78 %
Pinning
The reader supports USB host interface.
USB Interface Molex Header (4 pins) Molex Part Number: 53261-0471
Pin#| Name| Type| Description
1| PWR| Power| 5V Power Supply
2| D-| Data| USB-Data inverted
3| D+| Data| USB-Data
4| GND| Power| Signal and Power Ground
General regulatory requirements for 12117-810
FCC ID: OKY12117810A01A
IC: 7657A-12117810
Contains FCC ID: QOQ-BGM220S
Contains IC: 5123A-BGM220S
NOTICE:
This device complies with Part 15 of the FCC Rules and with Industry Canada
licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications made to this equipment not expressly approved by
BALTECH AG may void the FCC authorization to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
BALTECH AG
Lilienthalstraße 27
85399 Hallbergmoos
Germany
Phone: +49 (811) 99 88 1- 0
FAX: +49 (811) 99 88 1- 11
e-mail: info@baltech.de
http://www.baltech.de/
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>