Baltech 10090-640 RFID Reader User Manual
- June 5, 2024
- BALTECH
Table of Contents
Baltech 10090-640 RFID Reader
The “10090-XYZ” Reader/Writer is a desktop contactless smart card USB & Bluetooth wireless Technology Smart card reader and writer combining the high- and low frequency card technologies. It supports Mifare, ISO 14443A/B and ISO 15693 standards as well as all major 125kHz-based transponders. Based on BALTECH’s core technology it provides support of the latest smartcard technologies, encryption and security features.
Mounting and Connection
The reader generates magnetic field at 13.56MHz, 125 KHz and 2.4 GHz which
could be influenced by any electrically conductive material close to the
device.
To ensure good performances and functionalities in terms of read range and
reliability a minimum distance of 10cm from such materials is required.
Mounting the unit directly to metal would result in a severe reduction of read
range down to zero functionality. Care should be taken when testing the device
after mounting at a problematic environment: Read ranges and performance vary
from card to card and very much from card to tag or key-fob. When mounting
multiple readers, the distance between readers should be minimum 0.5 m in
order to avoid degradation of performance due to interference. To connect the
device to a host system (a printer or a PC), please make sure that the system
provides an USB socket intended for connection of the reader.
Operation
Whenever the device is connected to a proper power supply, it will switch on the internal antenna and periodically scan for a card. Once a card has been detected, the card number is read, the data converted and sent to the host system through the USB Interface. To enable the device to read cards, tags and key-fobs successfully, they should be placed centred above the reader.
Technical Features
Operating Frequency
| · 0.125MHz
· 13.56MHz
· 2402MHz-2480MHz
---|---
Data transmission modulation
reader to card:
| ASK
Data transmission modulation
card to reader:
| AM/Load modulation
Interfaces| USB: Full speed 2.0, RS 232, Bluetooth 5.2
Contactless Card
| Supported standards: ISO14443 A & B, ISO15693, Communication speed
ISO14443A/B: Baud rate up to 424kBaud
Operating Range| · ISO14443A/B: up to 5cm
· ISO15693: up to 8cm
· 125kHz: up to 6cm
· Bluetooth wireless technology: up to 10m
Human| Red, Green LEDs & Buzzer
Supply Power [VDC]| USB bus powered: 5V (±5%)
Power Consumption [W]| Up to 1.5 / 1 typ.
Operating Temperature [°C]| -20 to +65
Operating Humidity [%]| 20 to 80 relative humidity; non-condensing
Non-Operating Humidity [%]| 10 to 90 relative humidity; non-condensing
Antennas| · 2.4GHz internal Chip antenna
· 125kHz permanently attached coil antenna
· 13.56MHz integrates PCB loop antenna
Pinning
The reader supports USB host interface
USB Interface Molex Header (4 pins) Molex Part Number: 53261-0471
Pin#| Name| Type| Description
1| PWR| Power| 5V Power Supply
2| D-| Data| USB-Data inverted
3| D+| Data| USB-Data
4| GND| Power| Signal and Power Ground
General regulatory requirements for 10090-640
- FCC ID: OKY10090640A03B
- IC : 7657A-10090640
- Contains FCC ID: QOQ-BGM220S
- Contains IC: 5123A-BGM220S
FCC Statment
This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s).Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications made to this equipment not expressly approved by BALTECH AG may void the FCC authorization to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>