robustel R3000 Industrial LTE Cellular Dual SIM Router Owner’s Manual

robustel R3000 Industrial LTE Cellular Dual SIM Router

Regulatory and Type Approval Information

Table 1: Directives

2011/65/EU| The European RoHS2.0 2011/65/EU Directive was issued by the European parliament and the European Council on 1 July 2011 on the restriction of the use of certain Hazardous substances in electrical and electronic equipment.
---|---
On June 4, 2015, the Official Journal of the European Union published the RoHS2.0 Amendment Directive (EU)

In 2015/863, four phthalates (DEHP, BBP, DBP, DIBP) were officially included in the list of restricted substances in Appendix II of RoHS 2.0 (2011/65/EU).

From July 22, 2019, all electronic and electrical products exported to Europe (except medical and monitoring equipment) must meet this restriction; from July 22, 2021, medical equipment and

monitoring equipment will also be included in the scope of control.

2012/19/EU| The European WEEE 2012/19/EU Directive was issued by the European parliament

and the European Council on 24 July 2012 on waste electrical and electronic equipment.

2013/56/EU| The European 2013/56/EU Directive is a battery Directive which published in the EU official gazette on 10 December 2013. The button battery used in this product conforms to the standard of 2013/56/EU directive.

Table 2: Toxic or Hazardous Substances or Elements with Defined Concentration Limits

Metal

parts

| o| o| o| o| –| –| –| –| –| –
Circuit

modules

| o| o| o| o| o| o| o| o| o| o
Cables and cable assemblie

s

|

o

|

o

|

o

|

o

|

o

|

o

|

o

|

o

|

o

|

o

Plastic and polymeric

parts

|

o

|

o

|

o

|

o

|

o

|

o

|

o

|

o

|

o

|

o

o:

Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in RoHS2.0.

X:

Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials for this part might exceed the limit requirement in RoHS2.0.

-:

Indicates that it does not contain the toxic or hazardous substance.

Radio Specifications

Cellular Frequency*

| 4G: LTE FDD: B1/B2/B3/B4/B5/B7/B8/B28 LTE TDD: B40

3G: WCDMA: B1/B2/B5/B8

2G: GSM: B2/B3/B5/B8

| ****

Oceania, South America

4G: LTE FDD: B1/B3/B5/B7/B8/B20 LTE TDD: B38/B40/B41

3G: WCDMA: B1/B5/B8

2G: GSM: B3/B8

| ****

EMEA

Wi-Fi Frequency| 2.4 GHz: 2.412 ~ 2.484 GHz

5 GHz: 4.910 ~ 5.825 GHz

Max RF power| 35 dBm@GSM, 25 dBm@WCDMA, 25.7 dBm@LTE, 18dBm@Wi-Fi

• May vary on difference models.

Simplified EU Declaration of Conformity
We, Guangzhou Robustel Co., Ltd. are located at 501, Building #2, 63 Yongan Road, Huangpu District, Guangzhou, China, declare that this radio equipment complies with all applicable EU directives. The full text of the EU DoC is available at the following internet address:
www.robustel.com/certifications/

FCC Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

IC Declaration of Conformity
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Radio Frequency Exposure Statement for IC
This device complies with IC exposure limits set forth for an uncontrolled environment. This device shall be installed and operated with minimum distance 20cm between the radiator & body.

Find more product documents or tools at:
www.robustel.com/en/documentations/

Technical Support

• Tel: +86-20-82321505
• Email: support@robustel.com
• Web: www.robustel.com

Document History
Updates between document versions are cumulative. Therefore, the latest document version contains all updates made to previous versions.

Date| Firmware Version| Document Version| Change Description
---|---|---|---
Aug. 03, 2022| 5.0.0| 1.0.0| Initial release.
 |  |  |
 |  |  |
 |  |  |
 |  |  |
 |  |  |
 |  |  |
 |  |  |
 |  |  |
 |  |  |
 |  |  |

Overview

The Robustel Industrial Cellular VPN Router with 4 Ethernet Ports (R3000 Quad) is a rugged cellular router offering state-of-the-art mobile connectivity for machine-to-machine (M2M) applications.

Package Checklist

Before commencing installation ensure your package has the following components:

Panel Layout (May Vary on Different Models)

Interface Descriptions

PIN Assignment

LED Indicator

(250ms blink time)

| Router is powered on (System is initializing)
On, blinking

(500ms blink time)

| Router starts operating
Off| Router is powered off
PPP| Green| On, solid| Link connection is working
Off| Link connection is not working
USR-OpenVPN| Green| On, solid| OpenVPN connection is established
Off| OpenVPN connection is not established
USR-IPsec| Green| On, solid| IPsec connection is established
Off| IPsec connection is not established
USR-Wi-Fi| Green| On, solid| Wi-Fi is enabled and working properly
Off| Wi-Fi is disabled or not working properly
| Green| On, solid| High Signal strength (21-31) is available
Yellow| On, solid| Medium Signal strength (11-20) is available
Red| On, solid| Low Signal strength (1-10) is available
/| Off| No signal
NET| Green| On, solid| Connection to 4G network is established
---|---|---|---
Yellow| On, solid| Connection to 3G network is established
Red| On, solid| Connection to 2G network is established
/| Off| Connection to network is not established or establishing
SIM|

Green

| On, solid| Main card is being used
On, blinking| Backup card is being used
Off| NO SIM card

Note: You can choose the display type of USR LED. For more details, please refer to RT123_SM_RobustOS Software Manual Service > Advanced > System

System Settings > User LED Type.

Reset Button

status.
Restore to default

configuration

| Press and hold the RST button for 5~10 seconds, the RUN LED starts blinking quickly, the router will restore to default

configuration.

Restore to factory

default settings

| Once the operation of restoring default configuration is performed twice within one minute, the router will restore to factory

default settings.

Note: The more details please refer to _RT123_SMRobustOS Software Manual, 2.3 Factory Reset.

Ethernet Ports. R3000 Quad Router has 4 Ethernet port with two LED indicators. The yellow one is link indicator and the green one is speed indicator. For details about status, see the table below.

USB Interface

cannot be used for sending or receiving data from slave devices which connected to it. You can insert a USB storage device into the router’s USB interface, such as a U disk or a hard disk. If there have a supported configuration file or a router firmware in this USB storage device, the router will automatically update the

configuration file or the firmware. For more details, see _RT123_SMRobustOS Software Manual.

Hardware Installation

1. SIM Card Installation. Loosen the screws associated with the cover by using a screwdriver and then find the SIM card slot/Micro SD card slot. Press the card with finger until you hear a click and then tighten the screws associated with the cover by using a screwdriver. Put back the cover and tighten the screws associated with the cover by using a screwdriver.
2. Antenna Installation. Rotate the antenna into the antenna connector accordingly.
3. Mounting Kit installation. (Optional)
4. Terminal Block Installation. Insert the terminal blocks into the interfaces connector, then can connect the devices or sensors to the gateway via corresponding interfaces e.g. RS232/RS485, DIDO…
5. Power Supply installation. Following to the color of the head, connect the cable marked red to the positive pole through a terminal block, and connect the yellow one to the negative in the same way.
6. Grounding the Device. Grounding will help to prevent the noise effect due to electromagnetic interference (EMI). Connect the device to the site ground wire by the grounding screw before powering on.
7. Connect the Router to a Computer. Connect an Ethernet cable to any port marked ETH0~ETH3 at the bottom of the router, and connect the other end of the cable to your computer.

Login to the Device

1. Connect the router’s Ethernet port to a PC with a standard Ethernet cable.
2. Before logging in, manually configure the PC with a static IP address on the same subnet as the gateway address, click and configure “Use the following IP address”.
3. To enter the gateway’s web interface, type http://192.168.0.1 into the URL field of your Internet browser.
4. Use login information shown in the product label when prompted for authentication.
5. After logging in, the home page of the web interface is displayed, then you can view system information and perform configuration on the device.
6. The automatic APN selection is ON by default, if need to specify your own APN, please go to the menu Interface->Link Manager->Link Setting->WWAN Settings to finish the specific setting.
7. The more configuration details please refer to RT123_SM_RobustOS Software Manual. (END)

• Support: support@robustel.com
• Website: www.robustel.com
• ©2022 Guangzhou Robustel Co., Ltd. All rights reserved. Subject to change without notice.

References

• 4G/LTE/5G/Cellular Routers, Gateways and Modems for Industrial IoT - Robustel
• Documentation, User Guides, Product Documents | Robustel

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>