CLEAR DESIGN BLADE Stand-Alone Workstation Instructions
- June 8, 2024
- CLEAR DESIGN
Table of Contents
CLEAR DESIGN BLADE Stand-Alone Workstation
WORKSTATION
OVERVIEW
BLADE Stand-Alone
All parts listed are for a single workstation; additional parts will be needed for additional workstations
PARTS LIST
| CODE | QTY | DESCRIPTION |
|---|---|---|
| GB3072 | 1 | Surface |
| BB3 | 1 | Extra Long Beam |
| 2 | Lock Plate | |
| 2 | Cap Screw | |
| 1 | Locking Screw and Lever | |
| BL30 | 2 | BLADE 30” End Leg |
| 12 | Wood Screws | |
| BASB72 | 1 | 42” Support Bar* |
| 10 | Wood Screws |
*Part will be added to surfaces 72” and longer
JOIN END LEGS WITH BEAM
Insert beam tabs into leg brackets. Guide beam tabs into bracket holes,
ensuring that there is not a gap between the beam and legs.
Using a rubber mallet, hammer the beam to lock in place.
BOLT DOWN BEAM-TO-LEG LOCK PLATE
Note: The beam lock plates will not fit if there is a gap between the beam and the leg.
MEASURE AND ADJUST BEAM WIDTH
Measure from end leg to end leg until you find the approximate width of the work surface. Insert the screw through the overlapping beam slots and into the locking screw and lever. Slightly tighten the screw. DO NOT fully tighten. Insert beam grommet covers.
SECURE THE SURFACE
Position the surface on the desk frame. Align the outer sides of the surface flush and parallel with the outer sides of the end legs, adjust if not flushed. Insert wood screws into the leg brackets and secure to the underside of the surface.
SECURE BEAM
Tighten beam locks
OPTIONAL | INSTALL SUPPORT BAR
If working with a surface 72” or longer, use 10 wood screws to install support bar under the surface.
A1: SURFACE-MOUNT CABLE MANAGEMENT TRAY
OVERVIEW
BLADE Stand-Alone
If workstations have power, refer to BL-8 BLADE power guid
PARTS LIST
| CODE | QTY | DESCRIPTION |
|---|---|---|
| BHCT | 1 | Surface-Mount Cable |
| Management Tray | ||
| 10 | Wood Screws |
EXTEND CABLE TRAY TO DESIRED LENGTH
Extension range: 25″–45″.
TTACH CABLE TRAY TO SURFACE
Attach cable tray using wood screws.
A2: MODESTY PANEL
OVERVIEW
BLADE Stand-Alone
All parts listed are for a single modesty panel; additional parts will be needed for additional modesty panels.
PARTS LIST
| CODE | QTY | DESCRIPTION |
|---|---|---|
| **** GLMP## | 1 | Laminate Modesty Panel* |
| 4 | Machine Screws | **** |
| BMPBFB | 2 | L-Brackets |
| 4 | Wood Screws | **** |
*For Steel Modesty Panel: components may vary, but process is similar.
SECURE BRACKETS TO MODESTY PANEL
Connect the BMPBFB bracket to the modesty panel using screws. Secure tightly.
ATTACH MODESTY PANEL TO SURFACE
A3: LAMINATE INSET END PANELS
OVERVIEW
BLADE Stand-Alone
All parts listed are for a single panel; additional parts will be needed for
additional panels.
PARTS LIST5
| CODE | QTY | DESCRIPTION |
|---|---|---|
| GBEP## | 1 | Laminate Inset End Panel |
| LEPBL1 | 4 | End Panel T-Bracket |
| 8 | Self-Tapping Screws | **** |
| 8 | Wood Screws | **** |
SECURE BRACKET TO END LEGS
Attach 4 brackets to each BLADE end leg using the self-tapping screws.
- Inset–The back of the bracket will align flush with edge of leg.
- Flush–Back of bracket will be 9/16” from edge back edge of leg.
ATTACH END PANEL
Slide end panels into place and adjust until flush with bracket. Use 2 wood screws to secure panel to each bracket.
A4: STEEL INSET END PANELS
OVERVIEW
BLADE Stand-Alone
All parts listed are for a steel inset end panel; additional parts will be
needed for additional steel inset end panels.
PARTS LIST
| CODE | QTY | DESCRIPTION |
|---|---|---|
| BEP## | 1 | Steel Inset End Panel |
| 6 | Self-Tapping Screws |
SECURE PANELS TO END LEGS
Slide the end panel into place and adjust until either flush with outside of leg or slightly recessed.
ATTACH END PANEL
Use 4-6 self-tapping screws to secure panel to each leg.
1-866-304-7197
| inspire@mycleardesign.com
| mycleardesign.com
© 2022 Clear Design
| Version 22.1.4
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>