CLEAR DESIGN BLLBFV2 36 Inch Laminate Low Box Installation Guide
- June 9, 2024
- CLEAR DESIGN
Table of Contents
CLEAR DESIGN BLLBFV2 36 Inch Laminate Low Box
General Installation Guide
OPEN SHELF
OVERVIEW
Laminate Low Lateral
All parts listed are for a single open-shelf lateral; additional parts will be
needed for additional open-shelf lateral.
| CODE | QTY | DESCRIPTION |
|---|---|---|
| BLLOSV2 | 1 | Top Panel* |
1| Bottom Panel| **
1| Fixed Shelf Panel|
2| End Panels|
1| Back Panel|
4| Corner Feet|
-
SCREW CAM PINS INTO BOTTOM PANEL
Requires 6 cam pins.
-
INSERT HARDWARE INTO END PANELS
Requires 4 wooden dowels, 4 cam locks, and 4 cam pins.
-
INSERT HARDWARE INTO BACK PANEL
Requires 2 cam pins and 8 cam locks.
-
INSERT CAM LOCKS INTO FIXED SHELF
Requires 6 cam locks.
-
SECURE FIXED SHELF TO BACK PANEL
Align the cam pins so they sit inside of open cam locks. Use a screwdriver to turn cam locks clockwise and lock into place.
-
SECURE END PANELS
If working with a surface 72” or longer, use 10 wood screws to install support bar under the surface.
-
SECURE BOTTOM PANEL
Align the cam pins so they sit inside of open cam locks. Use a screwdriver to turn cam locks clockwise and lock into place.
-
SECURE TOP PANEL
Note: DO NOT Install top panel if you are merging storage.
Align the cam pins so that they sit inside of open cam locks. Use a screwdriver to turn cam locks clockwise and lock into place.
-
SECURE FEET TO BOTTOM PANEL
Attach corner feet to the bottom panel with 4 wood screws per foot.
END OF OPEN SHELF SECTION
BOX/FILE
OVERVIEW
Laminate Low Lateral
All parts listed are for a single low box/file lateral; additional parts will
be needed for additional low box/file laterals.
| CODE | QTY | DESCRIPTION |
|---|---|---|
| BLLBFV2 | 1 | **** Low Box/File Lateral |
| 2 | Handles | **** |
| 4 | Corner Feet | ** |
**
-
SECURE FEET TO STORAGE AND FLIP
Flip storage piece so it is laying on its back; secure foot to each corner using 4 wood screws.
-
ATTACH HANDLES
Using 2 bolts each, attach handles to front of drawers.
END OF OPEN SHELF SECTION 
MERGING TOP
OVERVIEW
Laminate Low Lateral
All parts listed are for a single merging top; additional parts will be needed
for additional merging tops.
PARTS LIST
| CODE | **** QTY | **** DESCRIPTION |
|---|
BLLBFV2
| ****
1
| ****
Low Box/File Lateral
| ****
BLLOSV2
| ****
1
| ****
Low Open-Shelf Lateral
| ****
GBLLT2
| ****
1
| ****
Laminate Merging Top
| ****
PLB.1
| ****
12
| ****
Laminate Storage L-Bracket
| ****
WD.2
| ****
24
| ****
Wood Screws
| ****
-
REMOVE DRAWERS FROM LOW BOX/FILE LATERAL
-
REMOVE STORAGE TOP
Locate the 6 cam locks across top edge on the inside of the storage piece. Then, use a screwdriver to turn cam locks counterclockwise to unlock. Carefully lift top from storage.
-
CONNECT BRACKETS TO TOP PANEL
Attach 12 laminate storage L-brackets to inside of storage using wood screws in the places shown below.
-
ATTACH TOP TO STORAGE
Set storage side-by-side then align top panel so it is flush with sides, back, and front of storage. Secure the 12 laminate storage L-brackets to top panel using wood screws.
-
INSERT DRAWERS
END OF OPEN SHELF SECTION
1-866-304-7197 |
[email protected] |
mycleardesign.com
© 2022 Clear Design | Version 22.1.4