LANCOM SYSTEMS LX-6200 Fast Wi-Fi 6 for Small and Medium User Densities User Guide

LANCOM SYSTEMS LX-6200 Fast Wi-Fi 6 for Small and Medium User Densities User Guide

Product Overview

• Reset button
  Pressed up to 5 seconds:
  device restart

Pressed until first flashing up of all LEDs:
configuration reset and device restart RESET

• Power supply socket
  After connecting the cable to the device, turn the connector 90° clockwise to prevent it from accidental unplugging. Use only the supplied power adapter.

• Ethernet interface
  Use the cable with the Ethernet connectors to connect interface ETH1 (PoE) to your PC or a LAN switch.

• USB interface
  Connect compatible USB devices either directly to the USB interface, or use a suitable USB cable.

Power

Off| Device switched off
Green, permanently| Device operational, resp. device paired / claimed and LANCOM Management Cloud (LMC) accessible.
Orange / green, blinking alternately with the WLAN link LED| The accesspoint is in managed mode and has not found a WLAN controller yet. The corresponding Wi-Fi module(s) is/are switched off until a WLAN controller has been found to supply a configuration, or until being switched manually into another operating mode.
1x green inverse blinking| Connection to the LMC active, pairing OK, claiming error
2x green inverse blinking| Pairing error, resp. LMC activation code / PSK not available.
3x green inverse blinking*| LMC not accessible, resp. communication error.
WLAN link

Off| No Wi-Fi network defined or Wi-Fi module deactivated. The Wi-Fi module is not transmitting beacons.
Green, permanently*| At least one Wi-Fi network defined and Wi-Fi module activated. The Wi-Fi module is transmitting beacons.
Green, inverse flashing| Number of flashes = number of connected Wi-Fi stations, followed by a pause.
Green, blinking| DFS scanning or other scan procedure

Hardware

Hardware

Power supply| 12 V DC, external power adapter (110 V or 230 V) w
Power consumption max.| 17.3 W
Environment| Temperature range 0–40 °C for wall mount with LANCOM Wall Mount (LN). Access point overheating is avoided by automatic throttling of the Wi-Fi modules. Humidity 0-95 %, non-condensing
Housing| Robust housing made of polycarbonate and aluminum, rear connectors, ready for wall and ceiling mounting; dimensions 205 x 42 x 205 mm (W x H x D)
Number of fans| None; finless design, no rotating parts, high MTBF
Wi-Fi
Frequency range| 2400–2483.5 MHz (ISM) or 5180–5700 MHz (country-specific restrictions possible)
Radio channels 2.4 GHz| Up to 13 channels, max. 3 non-overlapping (2.4 GHz band)
Radio channels 5 GHz| Up to 19 non-overlapping channels (available channels depending on country-specific regulation and connected with automatic, dynamic DFS channel selection.)
Interfaces
ETH1 (PoE)| 10 / 100 / 1000 Base-TX, PoE adapter compliant to IEEE 802.3at required
USB| USB 2.0 Hi-Speed Host-Port
BLE| The device is equipped with a BLE module and thus can transmit a configurable iBeacon.
Package content
Cable| Ethernet cable, 3 m
Power adapter| External power adapter, 12 V / 2.5 A DC/S, barrel connector 2.1 / 5.5 mm bayonet, LANCOM item no. 111884 (EU, 230 V) (not for WW devices)

Please observe the following when setting up the device

• The power plug of the device must be freely accessible.
• For devices to be operated on the desktop, please attach the adhesive rubber footpads
• Do not rest any objects on top of the device
• Keep all ventilation slots on the side of the device clear of obstruction
• Lockable wall and ceiling mounting with the LANCOM Wall Mount (LN) (available as an accessory)
• lease note that support service for third-party accessories is excluded.

Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!
Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.

The additional power LED statuses are displayed in 5-seconds rotation if the device is configured to be managed by the LANCOM Management Cloud.

This product contains separate open-source software components which are subject to their own licenses, in particular the General Public License (GPL). The license information for the device firmware (LCOS) is available on the device‘s WEB config interface under “Extras > License information“. If the respective license demands, the source files for the corresponding software components will be made available on a download server upon request.

Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in compliance
with Directives 2014/30/EU, 2014/53/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of the EU
Declaration of Conformity is available at the following Internet address: www .lancom-systems.com/doc

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>