HQ POWER HQLE10061 DJ LED Light User Manual

HQLE10061 DJ LED Light
User Manual

HQLE10061 DJ LED Light

3 CH

26 CH

Introduction

To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling. This device should be returned to your distributor or to a local recycling service. Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing HQPower! Please read the manual thoroughly before bringing this device into service. If the device was damaged in transit, do not install or use it and contact your dealer.

Safety Instructions

Read and understand this manual and all safety signs before using this appliance.
For indoor use only.
The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Do not stare at light source.
Minimum distance from lighted objects (metres).
This luminaire is not suitable for direct mounting on normally flammable surfaces (suitable only for mounting on non-combustible surfaces).

CAUTION
RISK OF ELECTRIC SHOCK. DO NOT OPEN.
Caution – To reduce the risk of electric shock, do not remove cover (or back).
No user-serviceable parts inside. Refer servicing to qualified personnel.
To avoid the risk of fire or electric shock, do not expose this product to rain or humidity.

• This device can be used by children aged from 8 years and above, and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the device in a safe way and understand the hazards involved. Children shall not play with the device. Cleaning and user maintenance shall not be made by children without supervision.
• Always connect the device to a grounded circuit to avoid risk of electrocution.
• Always disconnect mains power when the device is not in use or when servicing or maintenance activities are performed. Handle the power cord by the plug only.
• If the external flexible cable or cord of this device is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
• All cords and cables should be routed so that they will not be walked on or pinched by items placed upon or against them. Pay particular attention to the point where they exit the unit.
• Protect this device from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
• Do not remove the cover under any conditions. There are no userserviceable parts inside. Never operate this device when its cover is removed.
• Do not operate a visibly damaged device. Do not attempt to operate this device if the power cord has been frayed or broken.
• Always mount this device in a safe and stable manner. Mount this device in an area that will allow proper ventilation. Allow about 15 cm between this device and a wall.
• Do not use the luminaire with a cracked or broken protective shield. Disconnect immediately from the mains. The protective shield is not replaceable.
• Familiarise yourself with the functions of the device before actually using it.
• Always make sure to connect the device to an alternating current matching the value stated on the device.
• Always install the device in a well-ventilated location.
• Keep this device away from dust and extreme temperatures. Make sure the ventilation openings are clear at all times. For sufficient air circulation, leave at least 2.5 cm in front of the openings.
• Never carry or move the device from the power cord or any other moving part. Always use the bracket.
• In the event of an operating problem, stop using the device immediately.
• This device is not designed for permanent operation: regular operation breaks will prolong its live.

General Guidelines

• Refer to the Velleman ® Service and Quality Warranty on the last pages of this manual
• All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to the device is not covered by the warranty.
• Only use the device for its intended purpose. Using the device in an unauthorised way will void the warranty.
• Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.
• Nor Velleman nv nor its dealers can be held responsible for any damage (extraordinary, incidental or indirect) – of any nature (financial, physical…) arising from the possession, use or failure of this product.
• Keep this manual for future reference.

Installation

4.1 General Guidelines
WARNING
Minimum distance from lighted objects: 0.5 m.

• Have the device installed by a qualified person, respecting all applicable norms.
• Install the device on an even, fire-resistant, scratch-resistant, water-resistant and nonslippery surface.
• The carrying construction must be able to support 10 times the weight of the device for 1 hour without deforming.
• Make sure there is no flammable material within a 1 m radius of the device.
• Install the device in a location with few passers-by that is inaccessible to unauthorised persons.
• Install the device in a location where you can easily access the power cord.

4.2 Overhead Installation

• When hung, the device must always be secured with a secondary attachment e.g. a safety cable (not incl.).
  Secondary Attachment
  Hanger
  Where a hanger is provided, the bearing parts of the hanger shall be capable of supporting ten (10) times the weight of the luminaire without permanent deformation and shall be manufactured from non-combustible materials such as steel or its equivalent.
  Accessories
  The design of the luminaire shall be such that removable accessories, e.g. colour frames and barn doors, when properly inserted, cannot fall out of the luminaire.
  Secondary Suspension
  A secondary suspension shall be provided for the luminaire, except where the luminaire is arranged for floor mounting or if it is intended for handheld use. The secondary suspension shall be designed and mounted in such a way that in the event of a failure of the primary suspension, no part of the luminaire can fall. The secondary suspension must withstand a 30 cm vertical drop for 30 times.

• Never stand directly below the device when it is being mounted, removed or serviced. Have a qualified technician check the device once a year and once before you bring it into service.

• Overhead mounting requires extensive experience: calculating workload limits, determining the installation material to be used… Have the material and the device itself checked regularly. Do not attempt to install the device yourself if you lack these qualifications as improper installation may result in injuries.

• For truss mounting, use an appropriate clamp (not incl.) and fit an M10 bolt through the centre of the (folded) bracket.

4.3 Connection

• Have a qualified electrician carry out the electric connection.
• Connect the device to the mains with the power plug. All devices must be powered directly off a grounded switched circuit. Never connect the device to a dimmer or rheostat.
• The installation has to be approved by an expert before the device is taken into service.

Operation

The device can be used in the following modes:

• stand-alone mode
• master/slave
• with a DMX-512 controller.

5.1 Control Panel
Access the control panel functions using the four panel buttons located around the display.

| MENU| scroll through the menu options
---|---|---
ENTER| confirm a selection
UP| upwards through the menu list
DOWN| downwards through the menu list

5.2 Menu

3CH
auto| Auto| Au1-8| auto programme
sound| Soun| So1-8| sound programme
speed| SPEE| SP1-SP9| speed
sensitivity| SEns| Se1-Se9| microphone sensitivity
dimming| dIMM| dI1-dI9| master dimming
silent scene| SILE| on/oFF| closed/open light when no music in sound mode
slave| SLAV| Slave| slave mode
IR| InFr| on/oFF| IR remote signal reception enabled/disabled

5.3 Stand-Alone Mode
The device starts running in stand-alone mode after connection to the mains. This mode allows you to use the device without controller.
5.4 Master/Slave Mode

• The master/slave mode allows for connecting several devices to a single master device in a daisy chain.
• All slave devices will then work synchronously with the master device.
• Configure all slave units before connecting the master unit to the daisy chain.

5.5 DMX Mode

The DMX mode allows you to control the device with any universal DMX controller.

• All DMX-controlled devices need a digital start address so that the correct device responds to the signals. This digital start address is the channel number from which the device starts to “listen” to the DMX controller. The same starting address can be used for a whole group of devices or an individual address can be set for every device.
• When all devices have the same address, all the units will “listen” to the control signal on one particular channel. In other words: changing the settings of one channel will affect all devices simultaneously. If you set individual addresses, each device will “listen” to a separate channel number. Changing the settings of one channel will only affect the device in question.

Refer to page 3 of this manual for the DMX channel values.
5.6 Remote Control
Black Out
Press this button to black out the current active mode. Press again to return.
Auto

1. Press to enable the auto mode.
2. Press <+> or <-> to choose the different programmes.
3. Press to disable.

Sound

1. Press to enable the sound mode.
2. Press <+> or <-> to choose the different programmes.
3. Press to disable.

Strobe

1. Press to enable the strobe mode.
2. Press <+> or <-> to choose the different programmes.
3. Press to disable.

Speed

1. Press .
2. Press <+> or <-> to adjust the programme speed.

Sensitivity

1. Press .
2. Press <+> or <-> to adjust the microphone sensitivity.

DMX/%
Allows you to activate/de-activate the DMX mode.
Manual

1. Press .
2. Press , or to select your colour.
3. Press <+> or <-> to select the static colours.