LANCOM SYSTEMS WLC-30 WIFI Access Point User Guide

LANCOM SYSTEMS WLC-30 WIFI Access Point User Guide

Safety Information

• Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!
• Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.

Please observe the following when setting up the device

• The mains plug of the device must be freely accessible.
• For devices to be operated on the desktop, please attach the adhesive rubber footpads
• Do not rest any objects on top of the device and do not stack multiple devices
• Keep all ventilation slots of the device clear of obstruction

Product Overview

1. ➀ TP Ethernet interface (Uplink)
   Connect the Uplink interface to a LAN switch or a WAN modem with a suitable cable.

2. ➁ TP Ethernet interfaces
   Use one of the enclosed cables with the kiwi-colored connectors to connect the interface ETH 1 to ETH 4 to your PC or a LAN switch.

3. ➂ Serial configuration interface
   For configuration, connect the device and a PC with a configuration cable (cable sold separately).

4. ➃ USB interface
   You can use the USB interface to connect a USB printer or a USB flash drive for device configuration

5. ➄ Reset button
   Pressed up to 5 seconds: device restart
   Pressed until first flashing up of all LEDs: configuration reset and device restart

6. ➅ Power
   After connecting the cable to the device, turn the bayonet connector 90° clockwise until it clicks into place.
   Use only the supplied power adapter.

➀ Power

Green, permanently| Device operational, resp. device paired / claimed and LANCOM Management Cloud (LMC) accessible
Green/orange, blinking| Configuration password not set
Without a configuration password, the configuration data in the device is unprotected.
Red, blinking| Charge or time limit reached
1x green inverse blinking| Connection to the LMC active, pairing OK, device not claimed
2x green inverse blinking| Pairing error, resp. LMC activation code not available
3x green inverse blinking| LMC not accessible, resp. communication error

*) The additional power LED statuses are displayed in 5-seconds rotation if the device is configured to be managed by the LANCOM Management Cloud.

➁ AP Status

Green, permanently| At least one active access point is connected and authenticated; no new and no missing access point.
Green/orange, blinking| At least one new access point.
Red, permanently| The LANCOM Wi-Fi controller is not yet operational; one of the following elements is missing:

• Root certificate
• Device certificate
• Current time
• Random number for the DTLS encryption

Red, blinking| At least one of the expected access points is missing.
➂ Uplink

Off| No networking device attached
Green, permanently| Connection to network device operational, no data traffic
Green, flickering| Data transmission
➃ ETH
Off| No networking device attached
Green, permanently| Connection to network device operational, no data traffic
Green, flickering| Data transmission
➄ Online
Off| WAN connection inactive
Green, permanently| WAN connection active
Red, permanently| WAN connection error
➅ VPN
Off| No VPN connection active
Green, permanently| VPN connection active
Green, blinking| Establishing VPN connections

Hardware

Power supply| 12 V DC, external power adapter (110 or 230 V) with bayonet connector to secure  against disconnection
---|---
Power consumption| Max. 8.5 W
Environment| Temperature range 0–40 °C; humidity 0 95 %; non-condensing
Housing| Robust synthetic housing, rear connectors, ready for wall mounting, Kensington lock; measures 210 x 45 x 140 mm (W x H x D)
Number of fans| None; fanless design, no rotating parts, high MTBF

Interfaces

Ethernet port can be freely  configured (LAN, WAN, monitor port, off). LAN ports operate in switch mode or isolated. Additionally, external DSL modems or termination routers can be operated at the Uplink port together with policy- based routing.
USB| USB 2.0 Hi-Speed host port for connecting USB printers (USB print server) or USB data media (FAT file system)
Config (Com)| Serial configuration interface / COM port (8-pin Mini- DIN): 9,600 – 115,000 baud, suitable for optional connection of analog / GPRS modems. Supports the internal COM-port server.

WAN protocols

Ethernet| PPPoE, Multi-PPPoE, ML-PPP, PPTP (PAC or PNS) and plain Ethernet (with or without DHCP), RIP-1, RIP-2, VLAN, IP, GRE, L2TPv2 (LAC or LNS), IPv6 over PPP (IPv6 and IPv4/ IPv6 Dual Stack Session), IP(v6)oE (autoconfiguration, DHCPv6 or static)
---|---

Package content

2.1 / 5.5 mm bayonet,  LANCOM item no. 111303 (not for WW  devices)

Declaration of Conformity

Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in compliance with Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of the EU Declaration of Conformity is available at the following Internet address: www.lancom  systems.com/doc/

References

• DoC - LANCOM Systems GmbH

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>