Silverlit 84820 Bumper Drone Mini Instruction Manual

Silverlit 84820 Bumper Drone Mini

Content Delivery

Part Identification

Battery Installation and Charging

Flying the Drone

Trimming the Drone

Flight control: Take off and landing

Flight control

Fly mode setting (Beginner / Intermediates Advanced Mode)

Protective Bumper

A. Content Delivery (See picture A)

• A1. Bumper Drone Mini
• A2. Transmitter
• A3. Spare Propellers
• A4. USB Recharge Cable
• A5. Instruction Manual

B. Part dentification (See picture B)

• B1. Using a fork or tool, gently pry the blade from the motor shaft.
• B2. Replace new correct propeller
• B3. When replacing the rotor, please make sure the arrows on both Drone and propeller are in the same direction,

C. Battery Installation and Charging (See picture C) Transmitter Battery Installation

• C1. Press down the button (1) on the transmitter, and then follow the arrow (2) direction to push out the battery compartment cover.
• C2. Insert 2 AAA batteries in the battery compartment with correct polarity.
• C3. Close the battery Compartment, Charging the Drone
• C4. Connect the USB cable to a USB socket
• C5. Switch off the drone. Insert DC plug into the charging socket on the drone. The charging process will begin automatically and the green LED on drone will light up.
• C6. Unplug the charging plug when the LED turns off, charging is completed.

Warning
Remove these batteries from the unit by pulling up on one and each Battery positive by hand.
Do Not remove or install batteries using sharp or metal tools.

Note:

1. The Drone can operate for about 4-5 minutes per every 30-45 minutes charging.
2. Before recharging the battery, wait 10 -15 minutes for it to cool down.

D. Flying the Drone (See picture D)

Tip Piloting hints

• For controlling the sticks on transmitter, try not to push the sticks immediately to any extreme positions. It should be like steering a biked For the novice pilot (after the trimming procedure is completed), It Is highly recommended to focus exclusively on learning to control the there is no need to keep it straight.
• For the first flight, it is important to learn to keep the Drone at a constant left of around 1 meter with pilot masters this, he may start learning to take control With the right stick.

1. Procedure for PAIR /SYNC the Drone and Transmitter
   2.4 GHz technology allows for many Drone to fly without signal interference, A connection, PAIR /SYNC, must be made between the these steps to PAIRISYNC the Drone and the transmitter. Turn the Power Switch button to “ON” position on the Drone, the LED will gradually fade in and out. (D1) Place the Drone on the ground with the tail pointing towards you and the noise pointing away – Turn the Power Switch on Transmitter to “ON” position, the LED will gradually fade in and out. (D2) -When the LED on Transmitter become solid and LEDS on Drone flash regularly, the pair procedure is completed. (D3)

2. Self Calibration
   Place the Drone on a horizontal surface. Pull the direction stick to lower left corner and press and hold “Descend” button (D4) for 8 seconds. You will hear a “beep” sound. The When “beep beep beep sound presents meaning that the calibration is completed. You can control the Drone now. (Only do the Self ( happened.)

3. Flight environment
   Indoor environment with calm air, Beware of the air circulation from the air- conditioner Caution: There must not be any dangerous objects (electric fan, air-conditioner, reading lamp, etc) on the flight path.

E. Trimming the Drone (See picture E)
Press the Ascend button to take-off the Drone about 0.5 to1 meter above the ground.

F. Flight control: Take off and landing (See picture F)
Auto take-off & landing:

G. Flight control (See picture G)

H. Fly mode setting (See picture H)

• Vertical press the stick gently (H1) to change between Beginner Mode (beep once) (H2) / Intermediates Mode (beep 2 times) (H3) /Advanced (beep 3 times) (H4) .

I. Protective Bumpers
The bumpers are highly protective to keep propellers away from obstacles, to prevent crash and fall.

Troubleshooting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>