silverlit FCC84813 Bumper Drone HD Instruction Manual
- June 3, 2024
- Silverlit
Table of Contents
silverlit FCC84813 Bumper Drone HD
Content Delivery (See picture A)
- Bumper Drone HD
- Transmitter
- Spare Propellers
- USB Charger
- Charge Cable
- Instruction Manual
- B1. Turn the screwdriver anti-clockwise to the loose screw and remove od propeller
- B2. Replace the new correct propeller and tight screw by turning clockwise
- B3. hen replacing the rotor. please make sure the arrows on both Drone and propeller are in the same direction.
- B4. Rotate the cover anti-clockwise to open the battery and Micro SD Card sbt compartment of the Drone.
- B6. Cose tne cover in the correct position and rotate clockwise until the engraving marks are aligned. battery Installation and Charging (See picture C) Transmitter Battery Installation
- Ci. Press down the button (1) on the transmitter, and then follow the arrow (2) direction to pull out the battery cover.
- C2. Insert 3 AA batteries in the battery compartment with the correct polarity.
- c3. Close the battery compartment.
- C4. Open the drone’s battery compartment and disconnect the battery from the drone
- Co. Unplug the charging plug when the LED tums off, and charging is completed.
- Co.Connect the battery to 3 USE Charger and charge cable then to aUS5 AGA08pler.
- C7. Do not charge the pottery through the computer.
Note
- The Drone can operate for about 4- 5 minutes every 60-85 minutes charging.
- Before recharging the battery, wait 10-15 minutes for it to cool down.
D. Flying the Drone (See picture D)
Tip Piloting hints
- For controlling the sticks on the transmitter, try not to push the sticks immediately to any extreme positions. It should be like steering a bicycle rather than pressing computer game sticks.
- For the novice pilot (after the trimming procedure is completed), it is highly recommended to focus exclusively on learning to control the sick fist. If the Drone turns around by itself there is no need to keep it straight. or the is important to earn to keep the Drone at a constant ert of around1 meter with very gentle inputs on the left stick. Once the plot masters this, he may start learning to take control of the night sick.
Procedure ror PAlRSN Ine rone and iransmiter
2.4 GHz technology allows many Drones to fly without signal interference. A
connection, PAIR/ SYNC, must be made between the Drone and the transmitter to
function. Follow these steps to PARISYNC the Drone
-
Ihsert and use the battery into the battery compartment fimy and connect with the plug on Drone, the LED Wll gradually fade in and out. (D1 and D2)
-
When the LEDs become fash. push the let stick to ton then all do to hotom/n E
-
Arming Motors (for manual take the let stick to the top then pull down to the bottom(03), LED on Drone will fash regularly, and the pairing procedure is completed. (D4)
Pull the left stick to the lower left comer and the right stick to the lower right comer simultaneously (05) and the motors will start spinning. Push the left stick up to access the Drone. (06) After descending the Drone, disarm the motors by pushing both sticks at the same time as the picture shows. (D5) -
Self Calibrationrati Pul the left and right a horizontal to the lower surface. left comer (07). After 8 seconds. You will hear a “best sound. The rotors will spin and calibration proceeds. When the Tong beep” sound is present meaning that the calibration is completed. You can then Drone now. environment (One does the Self Calibration when the unstable lying of the Drone happens
Flight environment
DO NO1 tv in bad weather, such as rain, wind or tog. The environment should be
0pen and void of buildings or other obstacles
please study this instruction Manual and understand all the features and
controls. For those who do not have any flight experience, please prior to
seeking instruction from an experienced person. Keep the drone away from
obstacles, persons and animals, power lines, trees, lakes, and rivers, etc. to
avoid interference between the transmitter and other Wireless equipment.
Warning!
When using a commercially-available USB AC adapter, make sure to use an
adapter with a power output of 1A or more. Charging via other types of
adapters may cause damage or malfunction.
Warning!
Remove these batteries from the unit by pulling up on one end of each battery
positive by hand, DO NOT remove or install batteries using sharp or metal
tools.
E. Trimming the Drone (In Normal Mode only) (See picture E)
After arming aunty push the left stick up to raise the Drone about 0.5 to 1
meter above the ground.
F. Flight control: Take off and left stick control (See picture F
)
Auto take-off & landing :
G. Flight control (See picture G)
H. Fly mode setting (Normal Mode and Headless Mode) (See picture H)
Switch to Normal Mode (H1), the directions control will be the same as the
Drone’s designed directions (H2). Switch to Headless Mode (H3). the directions
of the Drone will set and keep the same right after entering Headless mode.
From now even with controlling of the rotation of the Drone, the directions
control will be the same as the condition right after entering Headless mode.
(H4) Vertical press left stick gently (H5) to change between Beginner Mode
(beep once) (H6) / Intermediates Mode (beep 2 times) (H7) Advanced (beep 3
times) (H8)
Protective Bumpers
The bumpers are nighly protective to keep propellers away Trom obstacles, to
prevent crashes and 1all.
J. Download photos and videos
Step 1. Be sure the gallery of the Drone has been disconnected. Remove
the Micro SD card from Drone. Insert into the card reader and then connect
with the computer. A pop-up window will appear (J1).
Step 2. Open the PHOTO’ or “VIDEO’ Holder, and copy the images or videos
to your computer after you found the files (J2).
K. Troubleshooting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>