SilverLit EI-8340a Bumper Drone Instruction Manual

BUMPERDRONE HD

Content Delivery (Seo picture A)

A1. Bumper Drone HD A2. Transmitter A3. Spare Propellers A4.USB Charger AS. Instruction Manual

Part Identification (See picture B)

B1. Turn screwdriver anti-clockwise to loose screw and remove old propeller
B2. Replace new correct propeller and tight screw by turning clockwise
B3. When replacing the rotor, please make sure the arrows on both Drone and propeller are in the same direction.
B4. Rotate the cover anti-clockwise to open the battery and Micro SD Card slot compartment of the Drone.
B5. Close the Cover in correct position and rotate clockwise until the engraving marks aligned.

Battery Installation and Charging (See picture C) Transmitter Battery

installation

C1. Press down the button (1) on the transmitter, and then follow the arrow (2) direction to pull out the battery cover.
C2. Insert 3 AA batteries in the battery compartment with correct polarity.
C3. Close the battery compartment.

Charging  the Drone

21. USB AC adapter (commercially available) (not included)| 22. USB charger (supplied in this pack)| 23. Charging indicator

C4. Unplug the charging plug and remove the battery from Drone.
C5. Connect the battery to a USB charger then to a USB AC Adapter.
C6. Unplug the charging plug when the LED tums off, charging is completed.
C7. Do not charge the battery through computer.
Note: 1. The Drone can operate for about 4 – 5 minutes per every 60-85 minutes charging.
2. Before recharging the battery, wait 10 – 15 minutes for it to cool down.

Flying the Drone (See picture D)

Piloting hints

• For controlling the sticks on transmitter, try not to push the sticks immediately to any extreme positions. It should be like steering a bicycle rather than pressing computer game sticks.
• For the novice pilot (after the trimming procedure is completed), it is highly recommended to focus exclusively on leaming to control the left stick first. If the Drone turns around by itself there is no need to keep it straight. For the first flight, it is important to learn to keep the Drone at a  constant left of around 1 meter with very gentle inputs on the left stick. Once the pilot masters this, he may start learning to take control with the right stick.

1. Procedure for PAIR / SYNC the Drone and Transmitter
   2.4 GHz technology allows for many Drone to fly without signal interference. A connection, PAIR /SYNC, must be made between the Drone and the transmitter to function. Follow these steps to PAIR/SYNC the Drone and the transmitter.
   • Insert the battery into battery compartment firmly and connect with the plug-on Drone, the LED will gradually fade in and out. (D1 and D2) • • • Place the Drone on the ground with the tail pointing towards you and the noise pointing away.
   • Turn the Power Switch on Transmitter to “ON” position, the LED will gradually fade in and out.
   • When the LEDs become flash, push the left stick to top then pull down to bottom(D3), LED on Drone will flash regularly, the pair procedure is completed. (D4)

2. Arming Motors (for manual take off )
   Pull the left stick to lower left comer and right stick to lower right comer simultaneously (DS) and the motors will start spinning. Push the left stick up to ascend the Drone. (D6) After descending the Drone, disarm the motors by pushing both sticks at the same time as picture shown. (D5)

3. Self Calibration
   Place the Drone on a horizontal surface.
   Pull the left and right stick to lower left comer (D7). After 8 seconds. You will hear a “beep” sound. The rotors will spin and calibration proceeds. When ‘long beep” sound present meaning that the calibration is completed. You can control the Drone now. (Only do the Self Calibration when unstable flying of Drone is happened.)

4. Flight environment

5. Before your first flight, please study this Instruction Manual and understand all the features and controls. For those who do not have any flight experience, please prior to seek instruction from an experienced person.

6. DO NOT fly in bad weather, such as rain, wind, or fog. Los

7. The environment should be open and void of buildings or other obstacles.

8. Keep the drone away from obstacles, persons and animals, power lines, trees, lakes, and rivers, etc.

9. Try to avoid interference between the transmitter and other wireless equipment.

Trimming the Drone (In Normal Mode only) (See picture E)

After arming, gently push the left stick up to raise the Drone about 0.5 to 1 meter above the ground.

E1: Keep turning right
• When your Drone keeps turning right press left, side timmer continually until it slops turning.| E4: Keep going left
• When your Drone keeps rolling sideways to left, press right side of roll button continually until it stops rolling.
---|---
E2: Keep turning left
• When your Drone keeps turning left,  press right side timmer continually until it slops turning.| ES: Keep going forward
• When your Drone keeps going forward, press backward trimmer continually until it stops going forward.
E3: Keep going right
• When your Drone keeps rolling sideways to right, press left side of roll button continually until it stops rolling.| E6: Keep going backward
• When your Drone keeps going backward, press forward trimmer continually until it stops going backward

Flight control: Take off and left stick control (See picture F )

Press “Auto Take-Off / Landing ° button (F1), Drone flies up to a standard level and hover in the air.
The Drone can take off or land on quiet water surface (F2). Caution: do not push or submerse the Drone underwater. Water-resistant (IPX4 Rated) Press again “Auto Take-Off / Landing” button, Drone will land automatically. Press the “Stop” button for emergency stop.| Push up the left stick to ascend the Drone, push down to descend (F4), release to lock the left.

Flight control (See picture G)

G1 : Ascend and descend
When the Drone hovering in the air, slowly push the left stick up to ascend the Drone, or push it down a bit to descend the Drone. To maintain the current altitude, release it to return to center.| G3: Flying sideways
Maintain the Drone at a certain height. Push the right stick toward left to fly the Drone sideways to the left, and push it toward right to fly the Drone sideways to the right.
---|---
G2 : Turn left and right
Maintain the Drone at a certain height. Push the left stick toward left to turn the Drone anticlockwise, and push it toward right to turn it clockwise.| G4: Forward and backward flight
Maintain the Drone at a certain height. Push the right stick upward to fly the Drone forward, and pull it downward to fly the Drone backward.

Fly mode setting (Normal Mode and Headless Mode) (See picture H)

• Switch to Normal Mode (H1), the directions control will be the same as the Drone’s designed directions (H2).
• Switch lo Headless Mode (H3), the directions of Drone will set and keep the same right after entering Headless mode. From now even control rotation of the Drone, the directions control will be the same as the condition right after entering Headless mode. (H4)
• Vertical press left slick gently (H5) to change between Beginner Mode (beep once) (H6) / Intermediates Mode (beep 2 times) (H7) / Advanced (beep 3 times) (H8)

Protective Bumpers

The bumpers are highly protective to keep propellers away from obstacles, to prevent crash and fall.

Download photos and videos

Step 1. Be sure the battery of Drone has been disconnected. Remove Micro SD card from Drone. Insert it into card reader and then connect with computer. A pop-up window will appear (1).
Step 2. Open the “PHOTO” or “VIDEO” folder, copy the images or videos to your computer after your found the files (J2)

Troubleshooting

off (“OFF”).
• The battery of the Drone is weak.
• Drone enter into protected status when rotors have been locked| • Set the power switch to “ON”
• Charging the battery of drone
• Push the left stick to top then pull down to bottom once.
The Drone does not react,  poorly to operation by transmitter.| • PAIRING / SYNC Procedure is not yet completed or done.| • Repeat the PAIR/SYNC procedure again.
Loss of control| • Out of the control range of distance.
• Rotor blade is deformed or distorted.| • The transmission range is up to 30 meters in open space.
• The transmission range is up to 15 meters in water surface.
• Replace the rotor blade with the spare one provided.

Silverlit SAS, 80 rue Barthelemy Danjou, 92100 Boulogne-Billancourt / France.
© 2018 Silverlit. All rights reserved.
Bumperdrone HD™

Become our fan on facebook facebook.com/SilverlitToys
Visit us atwww.Silverlit.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>