AERIAL ASE 200-300-400 Portable Adsorption Dehumidification Instruction Manual
- June 9, 2024
- AERIAL
Table of Contents
ASE 200-300-400 Portable Adsorption Dehumidification
Instruction Manual
ASE 200-300-400 Portable Adsorption Dehumidification
PORTABLE ADSORPTION DEHUMIDIFICATION
ASE 200-300-400
IDEAL FOR DRYING AT LOW TEMPERATURES IN CONSTRUCTION, WATER DAMAGE AND
WATERWORKS INDUSTRIES 
PORTABLE ADSORPTION
DEHUMIDIFIERS – INTRODUCTION
ENSURING DRY CONDITIONS AT LOW TEMPERATURES
Adsorption dehumidification ensures dry conditions at low temperatures. This
makes the ASE portable range the obvious choice for drying out new buildings
or water damage during the winter season and for maintaining low levels of
relative humidity at facilities with a low ambient temperature.
Humidity problems are most often associated with hot and damp environments,
and usually a condense drying dehumidifier is applied. However, at ambient
temperatures below 10°C condensation is not very easily achieved, whereas
humid air and moisture from materials, open water surfaces, and production
processes can cause serious damage at even very low temperatures.
The ASE portable range offers reliable control of the relative humidity of the
air, and drying out water damage or newly constructed buildings even at winter
temperatures. After all, accidents happen regardless of the seasons, and
construction work goes on all the year round.
Sturdy and compact design
The portable units have been designed for easy handling and transportation. The sturdy stainless steel cabinets are surprisingly compact and low weight compared to capacity. The countersunk control panel is well protected and folding handles for carrying make the units easy to stack during transportation and storage.
Key features
- Ensures dry conditions at low temperatures
- Reliable control of the relative humidity of the air
- Sturdy and compact design
- Cabinet in stainless steel/hot galvanized powder coated steel
- Designed for easy handling and transportation
- Low weight
- Easy to stack during transportation and storage
- MID approved energy counter (optional with ASE 400)
- Hour counter
- Internal hygrostat (ASE 400: connection for external hygrostat)
Easy installation and service
The portable units are fast and easy to install. Just connect one or two hoses
to the dry air and one hose to the regeneration air outlet and lead it to the
outside. The cabinet provides easy access for internal cleaning and service,
and the air filter can be changed without opening the cabinet.
High-performance operations
The built-in hour and energy counter shows the accumulated hour and energy
consumption. The energy counter of the ASE 200/ASE 300 is very precise and has
the MID approval which is highest marked standard. The portable range offers
reliable high-performance operations at low temperatures and easy installation
ensure fast results in drying out constructions and emergency situations
minimizing the long-term damage caused by flooding. The portable units can run
continuously, or they can be controlled by internal hygrostat with the ASE
200/ASE 300 or external hygrostat with the ASE 400.
How the dehumidifier works
An adsorption dehumidifier is divided into two zones. In the drying zone humid
air from the air inlet passes through a silica gel rotor that adsorbs the
moisture and the dry air is returned to the room. In the regeneration zone hot
air is blown through the rotor drying out the silica gel and carrying the
moisture through the connected hose to the outside.
How an adsorption dehumidifier works
Applications
PORTABLE ADSORPTION DEHUMIDIFIERS
ASE 200
The ASE 200 is a robust compact adsorption dehumidifier with a silica gel
rotor as standard. Process air is drawn into the dehumidifier and through the
rotor, which slowly turns between two sections in the dehumidifier. The silica
gel rotor adsorbs the moisture from the air in the drying section. This
moisture is removed again by blowing hot air through the rotor in the
regeneration section. The process air leaves the dehumidifier as dry air, and
the moisture is led out of the room through the regenerated air outlet.
- MID approved energy counter
- Hour counter
- Internal humidistat
- One common fan for process air and regeneration air
- Cabinet in stainless steel / hot galvanized powder coated steel
- Low weight
- PTC regeneration heater
- Robust and compact metal construction
- Carrying handle
- Easy internal access for service and maintenance
- Four rubber bumpers to fix the unit in place
- Flexible dry air outlet
Optional accessories
| Regeneration air outlet
Thermaflex hose 80mm
6000-0004
---|---
| Dry air outlet
Superflextract hose 50mm
6000-0003
| Spare filter
5107-0005
PORTABLE ADSORPTION DEHUMIDIFIERS
ASE 200
Dimensions
| Specifications | Units | ASE 200 |
|---|---|---|
| Capacity (20°C/60% RH) | kg/24h | 18.75 |
| Air volume – dry air/regeneration air | m3/h | 210/110 |
| Ext. pressure – dry air/regeneration air | Pa | 150/50 |
| Operating temperature range | °C | -45 |
| Operating humidity range | % RH | Oct-95 |
| Nominal power consumption | W | 694 |
| Power supply | V/Hz | 230/1ph/50 |
| Sound level | dB(A) | 48 |
| Duct sizes: | ||
| Air inlet | Ømm | 125 |
| Dry air outlet | Ømm | 1 x 80 or 2 x 50 |
| Regeneration air outlet | Ømm | 80 |
| Power cord | m | 4.5 with plug |
| Protection class | IP23 | |
| Product size (h x w x d) | mm | 285 x 289 x 395 (incl. fittings and feet) |
| Weight | kg | 14 |
PORTABLE ADSORPTION DEHUMIDIFIERS
ASE 300
The ASE 300 is a robust
compact adsorption dehumidifier with a silica gel rotor as standard. Process
air is drawn into the dehumidifier and through the rotor, which slowly turns
between two sections in the dehumidifier. The silica gel rotor adsorbs the
moisture from the air in the drying section. This moisture is removed again by
blowing hot air through the rotor in the regeneration section. The process air
leaves the dehumidifier as dry air, and the moisture is led out of the room
through the regenerated air outlet.
- MID approved energy counter
- Hour counter
- Internal humidistat
- One common fan for process air and regeneration air
- Cabinet in stainless steel / hot galvanized powder coated steel
- Low weight
- PTC regeneration heater
- Robust and compact metal construction
- Carrying handle
- Easy internal access for service and maintenance
- Four rubber bumpers to fix the unit in place
- Flexible dry air outlet
Optional accessories
| Regeneration air outlet
Thermaflex hose 80mm
6000-0004
Dry air outlet
Thermaflex hose 100mm
6000-0000
---|---
| Dry air outlet
Superflextract hose
50mm
6000-0003
| Spare filter
5107-0005
PORTABLE ADSORPTION DEHUMIDIFIERS
ASE 300
Dimensions
| Specifications | Units | ASE 300 |
|---|---|---|
| Capacity (20°C/60% RH) | kg/24h | 25.7 |
| Air volume – dry air/regeneration air | 1 | 300/110 |
| Ext. pressure – dry air/regeneration air | Pa | 150/50 |
| Operating temperature range | °C | -45 |
| Operating humidity range | % RH | Oct-95 |
| Nominal power consumption | W | 1,040 |
| Power supply | V/Hz | 230/1ph/50 |
| Sound level | dB(A) | 57 |
| Duct sizes: | ||
| Air inlet | Ømm | 125 |
| Dry air outlet | Ømm | 1 x 100 or 2 x 50 |
| Regeneration air outlet | Ømm | 80 |
| Power cord | m | 4.5 with plug |
| Protection class | IP23 | |
| Product size (h x w x d) | mm | 352 x 337 x 429 (incl. fittings and feet) |
| Weight | kg | 18 |
PORTABLE ADSORPTION DEHUMIDIFIERS
ASE 400
Despite weighing out at just 25 kilos, the ASE 400 is the right choice for
applications that require an air change of up to 480m³/h (environments of up
to 450m³). That’s 20% more than other units of comparable size that are
currently on the market. With its integrated lifting handle and stackable
design, the unit has been designed for easy handling and transportation. It
comes with a built-in hour counter with an optional MID-approved energy
counter. The portable adsorption dehumidifiers can run continuously, or they
can be controlled by an external hygrostat. 
- Ventilation only mode available – if pre-set humidity level is exceeded, normal dehumidification mode starts (only with optional external hygrostat)
- Sturdy unit made of stainless steel and powder coated sheet steel, supported by four rubber non-marking feet
- Integrated lifting handle and stackable design for easy use
- The rotor unit is easy to remove for cleaning purpose
- Dynamic, safe and self-regulating PTC heating element
- Energy-efficient radial fan
- High-performance ECODRY G3-MH rotor for maximum water absorption
- Air filter on the process air inlet
- Noise reduced via integrated silencer: 60 dB
- Connection for external hygrostat
- Non-resettable hour counter
Optional accessories
| Regeneration air outlet
Thermaflex hose 80 mm
6000-0004
---|---
| Dry air outlet
Superflextract hose 125
6000-0012
| Spare filter
5107-0073
****| External hygrostat
6109-0040
PORTABLE ADSORPTION DEHUMIDIFIERS
ASE 400
Dimensions
| Specifications | Units | ASE 400 |
|---|---|---|
| Capacity (20°C/60% RH) | kg/24h | 36 |
| Air volume – dry air/regeneration air | m3/h | 480/185 |
| Ext. pressure – dry air/regeneration air | Pa | 150/100 |
| Operating temperature range | °C | -45 |
| Operating humidity range | % RH | Oct-95 |
| Nominal power consumption | W | 2,200 |
| Power supply | V/Hz | 230/1ph/50 |
| Sound level | dB(A) | 60 |
| Duct sizes: | ||
| Dry air outlet | Ømm | 125 |
| Regeneration air outlet | Ømm | 80 |
| Power cord | m | 4.5 with plug |
| Protection class | IP23 | |
| Product size (h x w x d) | mm | 410 x 395 x 560 |
| Weight | kg | 25 |
Dantherm A/S
Marienlystvej 65
DK-7800 Skive
Denmark
t. +45 96 14 37 00| SET Energietechnik GmbH
August-Blessing-Straße 5
71282 Hemmingen
Germany
t. +49 7150 94540
---|---
Dantherm Sp. z o.o.
ul. Magazynowa 5a
62-023 Gądki
Poland
t. +48 61 65 44 000| Dantherm GmbH
Oststraße 148
22844 Norderstedt
Germany
t. +49 40 526 8790
Dantherm AB
Fridhemsvägen 3
602 13 Norrköping
Sweden
t. +46 (0)11 19 30 40| Dantherm SAS
23 rue Eugène Hénaff
69694 Vénissieux Cedex
France
t. +33 4 78 47 11 11
Heylo GmbH
Im Finigen 9
28832 Achim
Germany
t. +49 4202 97550| MCS China
Unit 2B, No. 512
Yunchuan Road
Baoshang, Shanghai, 201906
China
t. +8621 61486668
Dantherm Ltd.
Unit 12, Galliford Road
Maldon CM9 4XD
United Kingdom
t. +44 (0)1621 856611| Dantherm S.p.A.
Via Gardesana 11
37010 Pastrengo (VR)
Italy
t. +39 045 6770533
Dantherm SP S.A.
C/Calabozos 6
(Polígono Industrial)
28108 Alcobendas, Madrid
Spain
t. +34 91 661 45 00| Dantherm AS
Løkkeåsveien 26
3138 Skallestad
Norway
t. +47 33 35 16 00
Dantherm LLC
Transportnaya 22/2
142800, Stupino
Moscow
Russia
t. +7 (495) 642 444 8| AirCenter AG
Täfernstrasse 14
CH-5405 Baden Dättwil
Switzerland
t. +41 43 500 00 50
KEEP UPDATED FOLLOW US ON:danthermgroup.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>