ELBA ESF-K1672 16 Inch Stand Fan Owner’s Manual
- June 4, 2024
- ELBA
Table of Contents
Owner’s Manual
STAND FAN
MODEL: ESF-K1672(GR)
ESF-K1672 16-Inch Stand Fan
Please read this manual carefully before operating your set. Retain it for
future reference. Record the model number and the serial number of the set.
See the label attached on the set and quote this information to your dealer
when you require service.
For The Warranty Terms & Conditions, Please Refer To Warranty Certificate.
REMOVE ALL PACKING MATERIALS FROM THIS PRODUCT BEFORE USING IT.
THIS APPLIANCE MUST BE INSTALLED ON A FLAT SURFACE. PLEASE ENSURE THE ELECTRIC
SUPPLY TO THIS APPLIANCE IS DISCONNECTED
Please read this instruction carefully. It is advisable to keep this
instruction manual in a safe place for future reference.
SAFETY PRECAUTIONS
- Keep electrical appliances out of reach from children. Do not let them operate the appliances without supervision.
- To protect against the risk of electrical shock, do not immerse the product, cord, or plug into water or any other liquid.
- This product is for household and indoor use only.
- This product is not intended for use by people (including children) with reduced physical, sensory or mental capabilities unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
- If the power cord or plug is damaged, it must be replaced by the service center or a qualified service technician to avoid hazards.
WARNING – to reduce the risk of fire, electrical shock, or injury to persons or property, please read and follow the below instructions carefully.
- Always operate the product from a power source of the same voltage, frequency, and rating as indicated on the product identification marking.
- Do not operate this product if it has malfunctioned, damaged cord or plug, or appears damaged in any way. Return the complete product to the place of purchase for inspection, repair, or replacement.
- This product should not be used in the immediate vicinity of water, such as bathtubs, washbowls, swimming pools, etc, where the likelihood of immersion or splashing could occur.
- Always switch off and unplug the plug from the outlet when not in use, before assembling or disassembling parts, and before cleaning. Fully assemble the fan before operating.
- Avoid contacting moving parts. Do not insert any object through the guard when the fan is operating.
- Do not cover the guard or operate in close proximity to curtains, etc.
- Always disconnect the fan when moving it from one location to another.
PRODUCT DESCRIPTIONS
1. Centre ring | 9. OSC knob |
---|---|
2. Front guard | 10. Speed button |
3. Guard ring | 11. Internal pole |
4. Spinner | 12. Height adjustment ring |
5. Fan blade | 13. Standing pole |
6. Guard nut | 14. Round base |
7. Rear guard | 15. Base screw |
8. Motor |
ASSEMBLY INSTRUCTIONS
- Open the gift box and check the parts by referring to the product description drawing.
- Insert the standing pole into the base and fasten the base screw. (Fig 1)
- Loosen the height adjustment ring and adjust the internal pole to the desired height. (Note: If you can’t see the internal pole, it may slide inside the standing pole. You can pull it out. Fig 2)
- Loosen the thumb screw on the back of the fan body and attach it to the internal pole.
- Fasten the thumb screw in alignment with the groove on the internal pole. (Fig 3)
FAN BLADE AND GUARDS ASSEMBLY
- Remove the spinner & guard nut from the motor shaft. Fix the rear guard to the front motor cover, then fasten the guard nut again. (Fig 4)
- Fix the fan blade to the motor shaft and make sure the stopper pin is fit into the groove of the blade. Turn the spinner counter-clockwise to fasten the blade. (Fig 5)
- Fix both fan guards with the guard ring and use a screwdriver to lock the screw. (Fig 6)
OPERATING INSTRUCTION
- Press buttons for speed control: “0″ for OFF; “1″ for Low speed; “2″ for Medium speed; “3″ for High speed.
- Press or pull up the OSC knob to control the fan oscillation. (Fig 7)
- The height of the fan can be changed by adjusting the internal standing pole.
CLEANING AND MAINTENANCE
Clean the appliance with a damp cloth with a mild cleaner. Do not use chemicals, steel, wooden or abrasive cleaners to clean the appliance.
WARNING: DO NOT IMMERSE THE APPLIANCE IN WATER. ENSURE THAT THE FAN IS UNPLUGGED FROM THE POWER SUPPLY BEFORE REMOVING THE GUARD.
MAIN SPECIFICATION
Voltage
Rated Power
Fan Size
Motor| : 220-240V/50Hz
: 50W
: 16-inch
: 3-Speed
---|---
NOTICE
This product must not be disposed of together with domestic waste. it has to
be disposed of at an authorized place for recycling of electrical and
electronic appliances. By collecting and recycling waste, you help to save
natural resources and make sure the product is disposed of in an
environmentally friendly and healthy way.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>