A LED Q290 Ceiling LED Light Instruction Manual
- June 9, 2024
- A LED
Table of Contents
A LED Q290 Ceiling LED Light
Important: Please read the instruction manual carefully prior to installation and keep it for future reference.
Ordering Code
| Product| Power (W)| Function Description
---|---|---|---
Fitting Series
| | | Sensor DIM,
Brida Sensor CCT Skumringsrelæ| Brida| 18| color temperature selectable, power
switchable
Accessories
| No. | Pic. | Qty. | Usage |
|---|---|---|---|
| 1 | 3 | Fix light | |
| 2 | 3 | Rawl plug | |
| 3 | 1 | Vandal-proof screw tool | |
| 4 | 3 | Plastic washer | |
| 5 | 2 | Fix cable clip | |
| 6 | 1 | Cable clip | |
| 7 | 1 | Cable clip | |
| 8 | 4 | Plastic plug |
- Mounting: Wall or Ceiling
- Light features:
- Ra: >80
- Life Time: 5 years
- Light Source: LED SMD2835
- Input: 220V-240V 50/60Hz
CCT:
| Electric Current | Power |
|---|---|
| 350mA | 10W |
| 500mA | 14W |
| 550mA | 15W |
| 700mA | 18W |
Colour Temperature Code
| Code | Colour Temperature | CCT(K) | Lumen |
|---|---|---|---|
| 30K | Warm White | 3000 | 2142 |
| 35K | Natural White | 3500 | 2196 |
| 40K | Cool White | 4000 | 2232 |
Installation
-
Unscrew the diffuser anticlockwise.
Vertically remove the diffuser and PCBA.
-
a. Cut off the power. Thread the input cable through the rubber plug to the fixture. Connect the L, N wire referring to the wiring diagram.
b. Knock the rawl plugs into the pre-drilled holes on ceiling/wall. Wear plastic washers on self-tapping screws and tighten them to fix the fixture on ceiling/wall.
-
Install the cable clip.
-
Connect the DC cable.
-
Mount the diffuser onto the base with screws.
-
Install the plastic plugs to hide the screws.
Wiring
Sensor Setting Options
Sensitivity
Sensitivity can be adjusted by selecting the combination on the DIP switches for different applications.
Hold-time
Hold-time refers to the time period that the light remains 100% on if no more movement is detected.
Daylight sensor
Different daylight threshold can be preset on DIP switches.
Light will always turn on upon movement if daylight sensor is disabled.
Stand-by time
This is the time period that the light remains at a low level before it is completely turned off.
Stand-by dim level
Light can be dimmed to different levels after hold-time.
Detection Pattern
Maintenance
- Cut off the main power first.
- Don’t touch LEDs while maintaining or cleaning.
- Don’t use chemicals to clean the fixture.
Environmental protection: waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
Caution
- The product must be installed by professional technicians and power supply must be cut off before installation.
- The diameter for AC input wire is 0.75mm² (complying with 60245 IEC57), which complies with the latest IEE electrical standards or national standards.
- Do not touch the electronic circuit and its components.
- Contact an authorised technical service centre for any repairs possibly required use only original spare parts.
- Do not touch LED while installing or maintaining.
- Sealing the entrance hole with glue after install is needed.
- The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
Instruction for Light Source Disassembly
- Unscrew the diffuser anticlockwise and vertically take it out.
- Disconnect the DC power cable from the driver.
- On the reverse of diffuser, use the screwdriver to pry the clips to release the PCBA, then twist the PCBA anticlockwise.
- Take out the PCBA (light source) from the diffuser.
This product contains a light source of energy efficiency class
A LED A/S Hammeren 6, DK-6800 Varde www.aled.dk +45 71995354
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>