Kurdene N06-A Wireless Electronic Earbuds User Manual

Kurdene N06-A Wireless Electronic Earbuds

Introduction

Thanks for using our wireless electronic products. For a good user experience, please read the manual carefully before using the products. Notice: To avoid unnecessary troubles, please do not disassemble these products by yourself, and please use the standard charger to charge.

Product Overview

❶ Choose the ear cap that suits you.

❷ Make sure that the ear caps face down and put the earbuds into the ear in the angle shown as the picture on the right.

❸ After putting on the earbuds, gently rotating the earbuds to a comfortable and secure position shown as picture 3 on the right. Now the earbuds are put on correctly!

❹ Error demonstration Do not wear the earbuds like the way shown as the picture on the right.

First time using

1. Take out the two earbuds from the charging case and peel off the insulating film.

2. Put the earbuds into the charging case and close the lid to charge(the earbuds are in charging state).

3. Open the cover of the charging case and take out the two ear buds, they will turn on and pair automatically and will be prepared for pairing to the phone.
   Warm notice : If the earbuds are not turned on or there is no sound come out, please put them back in the charging case again to make sure that they are in the charging state before taking them out for use (red/white light flash alternately)

4. The indicator of one earbud will go off and another will flash red and white light alternately.(ln pairing mode)

5. Turn on the Bluetooth function on your phone and search for IN06-A) and connect it.

Warm notice
i6. If indicators of both earbuds keep flashing red and white, Click either earbud’s power switch twice. Then the indicator of one earbud will flash red and white alternately, another will go off. (in pairing mode)
If you want to switch the Bluetooth connection to another device, please disable the Bluetooth function in the previously connected device OR delete the pairing name of “N06-A” from the original device. Then the pairing name of “N06-A”can be searched in new device and connected successfully.

Button Control

• The earbuds will automatically turn on after opening the top lid of the charging case.
  OR

• Press and hold the touch button for 5 seconds, then leave hold, the earbuds will turn on.(Not in the charging case and is in the off state)

• Put the earbuds into the charging case and close the lid, they will automatically shut down.
  OR

• While in the non-working state, press and hold the touch button for 6s, the two earbuds will be turned off at the same time.
  OR

• Automatically shut down after not connected for more than 5 minutes

Warm notice
For any single earbud, when it is in standalone mode, you can’t use it to play the previous song or decrease the volume.

Siri and other Voice Assistant

• iOS and part of the Android users can triple touch the left or right haptic button to tum on the voice assistant.

• The voice assistant will be automatically activated depends in different OS in mobile system.

Restore Factory Setting

1. Please turn off the Bluetooth of the mobile phone. When the red and white lights of the two earbuds are blinking, press the earbud 4 times quickly. The earbud will shut down after the reset is successful.

2. Delete the old pairing name on the Bluetooth terminal of the mobile phone and connect the earbud after ii is turned on.

Earbuds Indicator

Steps of charging for earbuds:

The earbuds will be charged when put into the charging case, and they will automatically tum off and disconnect when the charging case lid is closed.

earphone goes out
Re-Connection state| The red white light of the main earphone flashes, The light of the vice earphone goes out
Low battery| Red light of earbud flashes once every 6s
Charging| Red light on
Full battery| Red light off

Charging Case Indicator

off for 3s when in low battery state)
Two earbuds in charging state| White light flashes 4 times, then the white light stay on for 10s
One earbud in charging state| White light flashes twice, then the white light stay on for 10s

Specification

Voice Prompt

Charging the charging case

When the battery level is less than 10%, the orange light flashes frequently; Please use a charger with an output voltage of DC5V/1A to charge the charging compartment, and you can use a computer USB or other USB interface charger (Must choose a charger certified by a regular manufacturer)

Notice :

1. If the charging case is out of power, it may cause the earbuds to fail to shut down and remain connected to the phone even when they are placed in the charging case. So please remember to charge the charging case in time.

2. If moisture remains at the audio output hole, the sound may become fuzzy or completely inaudible. This is completely normal. In this case, please remove the earplugs and shake the audio output hole down several times to allow water to flow out or let it air dry for 1-2 hours, then the sound quality will become normal.

3. If there is noise, broken sound, or low sound, please take off the silicone ear cap and wipe it with a cotton swab.

4. If the earbud is not charged properly, wipe the charging column with a cotton swab, and then charge it again.

• The Charging cable is not waterproof

• The Charging cable is not waterproof

• Do not use hot water to disinfect the product

• If there is water droplet on the surface, please wipe it with a dry cloth before putting them back into the charging case to avoid damaging the device.

Tip:

1. If the product is dirty, please do not rinse it directly with water or use boiling water to soak and disinfect it. It is recommended to wipe the earbuds with an alcohol cloth or a wet paper towel.
2. If the product falls into the water accidentally, please pick ii up in time and dry it with natural wind or dry it in the sun for two hours before using ii. (otherwise it will affect the sound quality, thus fail to give you a better using experience)

Attentions

1. Do not use corrosive liquid to clean this product.
2. If comes into contact with chemicals, please rub ii with a damp cloth wet with clean water.
3. Do not use this product under extreme circumstances for temperature below -10 degree Celsius or above 60 degree Celsius .
4. To avoid explosion, please do not throw this product into fire.
5. To avoid scratches, please do not touch the earbuds with sharp objects.
6. Do not insert objects into the earbuds, otherwise ii would cause damage to the internal components.
7. Do not disassemble the earbud.
8. Please keep regular charge to earbuds, don’t leave them become empty battery status to keep their lifetime.
9. Please do not charge products with power adapter over 2A current. Excessive current may cause the damage to battery.

Battery Warning !
There is a built-in lithium battery in this product. To avoid explosion, do NOT expose the product to strong sunlight, fire or throw it into fire.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>