better bathrooms BeBa 26154 Mizar Mirrored Bathroom Cabinet User Manual
- June 9, 2024
- Better Bathrooms
Table of Contents
better bathrooms BeBa 26154 Mizar Mirrored Bathroom Cabinet
CONGRATULATIONS ON YOUR PURCHASE
Our aim at Better Bathrooms is to bring you extraordinary bathroom products,
for less.
If you’re after a modern, traditional, or a totally unique style bathroom, we
have the fittings and fixtures to bring your ideas to life, so you can fall in
love with your space every day.
We hope your new product goes above and beyond your expectations. However,
should any problems occur, please:
- Log in to your account and contact our customer services team via your self-service portal – betterbathrooms.com/CustomerAccount/Login
- Contact us via betterbathrooms.com/contact/contact-us
SAFETY
- This cabinet should be installed by a qualified electrician.
- This fitting is only suitable for connection to a 220-240V earthed supply in accordance with current IEE wiring regulations, and should be installed in accordance with local Building Regulations.
- This is for domestic, indoor use only.
- The cabinet should be connected to a dedicated lighting circuit which must be protected by a 5-amp fuse (or a 6 amp miniature circuit breaker).
- The electrical connection must be an adequate distance from the rear of the cabinet to prevent the risk of shorting with the cabinet’s casing.
- Before installing the fitting ensure that the mains supply is switched off, and that the appropriate fuse is removed (or appropriate circuit breaker is switched off) before commencing installation. Ensure that measures are taken to prevent the sup ply from being inadvertently reconnected.
- If there is a “Minimum Distance” label, please do not allow flammable materials to rest within that distance from the unit.
- This product may contain delicate parts – be careful during handling and maintenance to avoid breakage.
- Ensure the cover for the shaver socket is closed when not in use to prevent moisture from entering it.
- Only connect items designed to be used with a shaver socket (Such as shavers or electric toothbrushes).
- The shaver socket is not earthed and provides 230V at a maximum current of 80mA. Do not connect devices which require a higher current, different voltage, or an earth connection.
- If any modification is made to the fitting it will invalidate the warranty and may render the product unsafe.
- A defective appliance may cause electric shock. Never switch on a defective or damaged appliance. Disconnect the appliance from the mains before seeking assistance.
- This product is IP44 rated, and no part of the installation is allowed to be within bathroom Zones O or 1. Installation is permitted within Zone 2.
- This product must be earthed. Before commencing installation, ensure that there are no pipes or wires located behind the wall that may be damaged during drilling.
- Ensure that the hanging location has been decided upon and marked clearly to avoid unwanted damage to the wall due to incorrect positioning.
- Inspect the cabinet to ensure there are no signs of damage prior to installation.
- Take care unpacking, do not use a sharp blade to open as this may damage the product and void your warranty.
- Once installed a bead of silicon can be applied between the cabinet and the wall across the top and sides of the unit. Never seal the bottom of the cabinet to the wall, as th is may allow water to accumulate behind the unit.
- Ensure that the infrared sensor will be easily accessible following installation and that at least 20cm of space is left around the sensor to ensure correct operation.
BATHROOM ZONES
- Zone 0: The interior of the bathtub or shower basin.
- Zone 1: The area around the bathtub or shower basin up to a height of 2.25m above the floor
- Zone 2: The area stretching to 0.6m outside the bath or shower and above the bath or shower if over 2.25m
PARTS SUPPLIED
PLEASE NOTE: It is the responsibility of the installer to ensure that the fittings are suitable for the type of wall. Alternative fittings may be required (Not Supplied). If unsure professional advice should be sought.
TOOLS REQUIRED
INSTALLATION
The cabinet is supplied with a hanging bar to mount the cabinet onto the wall. At the back of the cabinet there is a corresponding bar which is designed to slot onto the hanging bar.
- Choose the desired position of the cabinet, and from that determine the required position of the hanging bar.
- Hold the hanging bar in position, using a spirit level to ensure it is level.
- Use a pencil to mark the position of the 3 holes on the wall.
- Place the hanging bar to one side, and drill the holes with a suitable drill bit.
- Insert wall plugs into the holes, ensuring they are flush to the wall.
- Place the hanging bar onto the wall, lining up the 3 holes with the wall plugs.
- Secure the hanging bar to the wall using the supplied screws.
- You will now be able to hang the cabinet. Carefully lower the cabinet onto the hanging bar, ensuring that is secure and will not slide.
- Open the cabinet door and mark the wall with a pencil through the security hole on the back panel.
- Remove the cabinet, drill the hole then place a wall plug into the hole you have just drilled.
- Hang your cabinet back up onto the hanging bar and ensure that the in the cabinet is lined up with the wall plug.
- The cabinet should now be connected to a suitable fused spur following current regulations and guidance. We would advise for this to be situated directly behind the cabinet below the hanging bar. When connecting ensure that enough cable is left to allow the cabinet to be safely removed from the hanging bar.
- Secure the cabinet to the wall using a screw through the security hole and into the wall plug you previously installed.
DOOR ADJUSTMENT
If the door is not level, you can adjust it using the hinge screw. Turning the
screw clockwise will push the door right, and turning anticlockwise will pull
it right.
SHELF ADJUSTMENT
Loosen the snap screw on the shelf to adjust the shelf position. Once the
shelf is in the correct position and level the screw should then be re-
tightened.
OPERATION
Your mirror comes with an infrared sensor located on the right-hand side. To
activate the light, move your hand across the sensor once at a distance of
around 5cm.
To turn the light off, move your hand across the sensor again.
SHAVER SOCKET
Your mirror comes with an inbuilt shaver socket located on the inside of
the mirror above the top shelf. This socket is only designed for use with
shavers.
Once the mirror is connected to the mains, the shaver socket should be ready
to use. Do not leave shavers plugged in when unattended and ensure that the
socket cover is in place when not in use.
CLEANING AND MAINTENANCE
Never use products containing bleach or abrasive cleaners, as these will have
a detrimental effect on the appearance and lifespan of the product.
Use a clean micro fiber cloth to clean the mirror.
DISPOSAL
Recycling facilities are now available for all customers at which you can
deposit your old electrical products. Customers will be able to take any old
electrical equipment to participating sites run by their local councils.
Please remember that this equipment will be further handled during the
recycling process, so please be considerate when depositing your equipment.
Please contact the local council for details of your local household waste
recycling centers.At the time of printing the product contains no substances
listed within Annex XIV of the Reach Regulations (EC) 1907 /2006. In
accordance with Article 59 of the same regulation the following substances are
contained within the product at permitted levels: Cadmium.
As a responsible manufacturer the regulations are monitored to ensure
continued compliance. Further information can be provided upon request.
TECHNICAL SPECIFICATION
- Model BeBa 26154
- WxHxD (mm) 600x700x130
- Net Weight (Kg) 16
- Power Cord length (cm) 50
- Rated Power (W) 25
- IP Rating IP44
- Input 220 – 240V, 50 Hz
- Shaver Socket Output 230V, 50Hz, 80mA
Formore information
visit betterbathrooms.com
email
customerservices@buyitdirect.co.uk
call 0330 390 3062
write to Trident Business Park, Neptune Way, Huddersfield, HD2 1UA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>