better bathrooms Freestanding Double Ended Roll Top Bath User Manual

better bathrooms Freestanding Double Ended Roll Top Bath

Product Information

The freestanding bath is a bathroom product that is designed to provide an extraordinary bathing experience. It comes in both modern and traditional styles and is accompanied by  fixtures, fittings, and furniture to match. The product is manufactured by one of the UK’s largest independent bathroom stores and has received numerous awards, including the National Business Awards UK, the Digital Entrepreneur Awards, and being placed on The Sunday Times Fast Track 100. The product is not designed to take weight on the rim and should not be sat or stood on.

General Instructions

The freestanding bath requires two-person assembly and should be installed by professional tradespeople. The product comes with feet set at 3mm above the floor. The installation process requires tools such as a spirit level, wrench, tape, marking pencil, and silicone gun. Before drilling, always check for pipes and cables. Flexible connector and waste trap are not supplied with the product.

Receiving and Protecting Your Bath

After receiving your bath, please unpack and remove all covering, checking whether there is any damage. Repack the bath if it is not being immediately installed. It will be rejected any
claim for damage if not notified in a timely manner. Before commencing installation, ensure the bath is completely protected, leave covering in place until the bathroom is complete. Scratches and damage incurred during installation are not covered by the warranty.

Installation

Apply silicone around the base surrounding of the bath before installing. Do not use the bath within 24 hours to let the silicone fully cure. Water test your bath prior to enclosing to ensure it drains correctly as no claims for non-draining baths will be valid after enclosing or tiling has been done; Water test overflow pipe and waste to ensure they are not leaking. The pre- fitted waste has NOT yet been fully installed. Please use a qualified installer to secure it to the bath to avoid any water leaking. Before use please test the bath to ensure the waste has been properly installed.

Troubleshooting

Marks found on the surface could be wiped off with a wet cloth and toothpaste.

Maintenance and Cleaning

Regular maintenance and cleaning of the freestanding bath are required. Water testing should be done periodically to ensure it drains correctly. Scratches and damage incurred during cleaning are not covered by the warranty.

Product Information  Bath with Metal Feet

The bath with metal feet is a bathroom product that requires two-person assembly and should be installed by professional tradespeople. Always check for pipes and cables before drilling.
The product is not designed to take weight on the rim and should not be sat or stood on.

General Instructions

Please read these instructions thoroughly and retain for future reference.

Contact Information

If you encounter any problems, please contact us via betterbathrooms.com/content/contact-us.

Important information

• Please read these instructions thoroughly and retain for future reference
• Pressures should meet minimum stated on the website
• Pressures must be balanced for optimum performance
• Always check for pipes and cables before drilling
• Freestanding bath is not designed to take weight on the rim, Do not sit or stand on the bath rim.

Receive Your Bath

Unpack and check for damage.
After receiving your bath, please unpack and remove all covering, checking whether there is any damage. Repack the bath if it is not being immediately installed. It will be rejected any claim for damage if not notified in a timely manner.

Protect your bath.
Before commencing and installation, ensure the bath is completely protected, leave covering in place until the bathroom is complete. Scratches and damage incurred during installation are not covered by the warranty.

Tools required

Installation Instructions

• Step 1: Adjust the bath feet until the bath base is 3mm above the floor; This can be done by turning the feet bars accordingly; Then use wrench to tighten the nuts on the bars. See figure 1
• Step 2: Mark the floor with the outline of the bath, at the final installation position with the marking pencil.
• Step 3: Carefully tilt the bath on its side and use flexible connector to connect the waste outlet to the trap as illustrated on figure2.
• Step 4: Position the bath on the floor marking as marked on step 2, make sure that flexible connector is not kinked upward on installation as this will result in drainage issue

Figure 1
Flexible connector installation
Figure 2
Flexible connector and waste trap are not supplied Feet set at 3mm above the floor

• Step 5
  Apply silicone around the base surrounding of the bath, see figure 3.

Do not use the bath within 24 hours to let the silicone fully cure

Troubleshooting
Marks found on the surface could be wiped off with wet cloth and toothpaste.

Maintenance & Cleaning

1. To preserve the polished surface, after using your bath, clean with soft cloth and warm soapy water to wash away any body oils or soap residue that forms a ring tide mark.
2. Do not use powders, pastes, crème cleaners, thinners, window cleaning sprays or dry cleaning liquid, etc.
3. When coloured essentials oils are used, first test that the colour won’t stain your bath. Always add oils into a bath full of water. Never pour them into an empty bath.

Water testing
Water test your bath prior to enclosing to ensure it drains correctly as no claims for nondraining baths will be valid after enclosing or tiling has been done; Water test overflow pipe and waste to ensure they are not leaking.
! Warning (apply to bath pre fitted with waste)
The pre-fitted waste has NOT yet been fully installed. Please use a qualified installer to secure it to the bath to avoid any water leaking. Before use please test the bath to ensure the waste has been properly installed.

Parts

Tools required

Installation

• Step 1
  1. Ensure the bath is on a soft surface to protect against scratches.
  2. Place the bars onto the bath, along with the washers and nuts as shown below, do not tighten at this stage to allow for adjustment, taking care not to damage the newly painted surface.

• Step 2
  1. Position the feet onto the bars and secure using the nuts and bolts provided.
  2. Adjust the position of the feet to align with the bath.
  3. Tighten all of the nuts so that the feet are secured to the bar and the bars are secured to the bath.

Troubleshooting
Movement in the feet after assembly Please check the feet are assembled properly, make sure fastener washers and washers are placed correctly.

Maintenance & Cleaning

• Marks on the painted surface should be wiped clean with a soft damp cloth and dried.
• Marks on the inside of the bath, should be cleaned using a soft damp cloth, for more stubborn marks, toothpaste can be applied and then rinsed thoroughly.
• No harsh cleaning chemicals or abrasive materials can be used on any surface.
• If using coloured oils/creams, carry out a test on small area prior to use to ensure that these will not cause staining.
• Never pour coloured oils/creams directly into an empty bath, always apply them into the bath water.

! Warning
Pay attention to below points if the bath is designed with tap deck.

1. The tap holes are not pre-drilled on the deck, drill holes according to your need.
2. Check and silicone the tap holes to make sure they are solid after drilling.
3. Check and make sure that there is no water leakage at the faucet.

Congratulations on your purchase
And welcome to our growing gang of savvy shoppers We’re on a mission to bring you extraordinary bathroom products, for less. From modern to traditional style ceramics, plus the gorgeous fixtures, fittings and furniture to match. So, you can fall in love with your space every single day. As one of the UK’s largest independent bathroom stores, we’ve received countless awards; including the National Business Awards UK, the Digital Entrepreneur Awards and being placed on The Sunday Times Fast Track 100. We hope your new product goes above and beyond your expectations. However, should any problems occur, please:

• log in to your account and contact our customer services team via your self-serve portal – betterbathrooms.com/CustomerAccount/Login
• contact us via betterbathrooms.com/content/contact-us

For more information

• visit betterbathrooms.com
• email customerservices@buyitdirect.co.uk
• call 0330 390 3062
• write to Trident Business Park, Neptune Way, Huddersfield, HD2 1UA

References

• Contact Us | Better Bathrooms
• Better Bathrooms - Login

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>