SKIL HD6294B-00 20V Brushless Sub-Compact Hammer Drill Owner’s Manual

SKIL HD6294B-00 20V Brushless Sub-Compact Hammer Drill

• Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
  – Lead from lead-based paints.
  – Crystalline silica from bricks, cement, and other masonry products.
  – Arsenic and chromium from chemically-treated lumber.

• Your risk from these exposures varies, depending upon how often you do this type of work.
  To reduce your exposure to these chemicals:
  – Work in a well-ventilated area.
  – Work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.
  – Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth or eyes or to lie on the skin may promote absorption of harmful chemicals.

GENERAL POWER TOOL SAFETY WARNINGS

Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

Work area safety

Keep work area clean and well lit. Cluttered or dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.

Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

Dress properly. Do not wear loose clothing or jewelry. Keep your hair, and clothing away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.

If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce disrelated hazards.

Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally

Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean and free from oil and grease.
Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Battery tool use and care

Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.

Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 265 °F (130 °C) may cause explosion.

Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

Service

Have your power tool serviced by a qualified repair person using only identical  replacement parts. This will ensure that the safety of the power tool is maintained.

Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers

SAFETY WARNINGS FOR HAMMER DRILL

Safety instructions for all operations:

Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss. Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory or fastener may contact hidden wiring. Cutting accessory or fastener contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

Safety instructions when using long drill bits:

Never operate at higher speed than the maximum speed rating of the drill bit. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.

Always start drilling at low speed and with the bit tip in contact with the workpiece.
At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend causing breakage or loss of control, resulting in personal injury.

SYMBOLS

Safety Symbols

The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols and the explanations with them deserve your careful attention and understanding. The  symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are no substitutes for proper accident prevention measures.

Be sure to read and understand all safety instructions in this Owner’s Manual, including all safety alert symbols such as “DANGER”, “WARNING”, and “CAUTION” before using this tool. Failure to following all instructions listed below may result in electric shock, fire, and/or serious personal injury

The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols.

| This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
| DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
| WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
``| CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, will result in minor or moderate injury.

Damage Prevention and Information Messages

These inform the user of important information and/or instructions that could lead to equipment or other property damage if they are not followed. Each message is preceded by the word “NOTICE”, as in the example below:
NOTICE: Equipment and/or property damage may result if these instructions are not followed.Removable Belt Clip

The operation of any power tools can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend a Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection which is marked to comply with ANSI Z87.1.

SYMBOLS (CONTINUED)

IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and more safely.

V

| Volts| Voltage (potential)

A

| Amperes| Current

Hz

| Hertz| Frequency (cycles per second)

W

| Watt| Power

kg

| Kilograms| Weight

min

| Minutes| Time

s

| Seconds| Time

Wh

| Watt-hours| Battery capacity

Ah

| Ampere-hours| Battery capacity

ø

| Diameter| Size of drill bits, grinding wheels, etc.

n0

| No load speed| Rotational speed, at no load

n

| Rated speed| Maximum attainable speed

…/min

| Revolutions or reciprocations per minute (rpm)| Revolutions, strokes, surface speed, orbits, etc. per minute
O| Off position| Zero speed, zero torque…
1,2,3,… Ⅰ, Ⅱ, Ⅲ,| Selector settings| Speed, torque, or position settings. Higher number means greater speed
| Infinitely variable selector with off| Speed is increasing from 0 setting
| Arrow| Action in the direction of arrow
| Alternating current (AC)| Type or a characteristic of current
| Direct current (DC)| Type or a characteristic of current
| Alternating or direct current (AC / DC)| Type or a characteristic of current
| Class II tool| Designates Double Insulated Construction tools.
| Protective earth| Grounding terminal
| Li-ion RBRC seal| Designates Li-ion battery recycling program
| Read the instructions| Alerts user to read manual
| Wear eye protection symbol| Alerts user to wear eye protection
| Always operate with two hands| Alerts user to always operate with two hands
| Do not use the guard for cut-off operations| Alerts user not to use the guard for cut-off operations

SYMBOLS (CERTIFICATION INFORMATION)

IMPORTANT: Some of the following symbols for certification information may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and more safely.

Laboratories.
| This symbol designates that this component is recognized by Underwriters Laboratories.
| This symbol designates that this tool is listed by Underwriters Laboratories, to United States and Canadian Standards.
| This symbol designates that this tool is listed by the Canadian Standards Association.
| This symbol designates that this tool is listed by the Canadian Standards Association, to United States and Canadian Standards.

| This symbol designates that this tool is listed by the Intertek Testing Services, to United States and Canadian Standards.

GET TO KNOW YOUR HAMMER DRILL

20V Brushless Sub-Compact Hammer Drill

SPECIFICATIONS

OPERATING INSTRUCTIONS

To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach, or bleach-containing products, etc., can cause a short circuit

If any parts are damaged or missing, do not operate this product until the parts are replaced. Use of this product with damaged or missing parts could result in serious personal injury.

Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modifications misuse and could result in a hazardous condition leading to possible serious injury.

To prevent accidental starting that could cause serious personal injury, always remove the battery pack from the tool when assembling parts.

This cordless hammer drill must be used only with the battery packs and chargers listed
below:

Battery Pack|

Charger

---|---
2Ah| 2Ah| 2.5Ah| 4Ah| 5Ah
SKIL BY519701| SKIL BY519702| SKIL BY519703| SKIL BY519601| SKIL BY519603| SKIL SC535801| SKIL QC536001
SKIL QC5359B-02| SKIL SC5358B-02

To Attach/Detach Battery Pack

(Fig. 2)

Lock the trigger switch “OFF” on the tool by placing the direction-of-rotation (forward/centerlock/reverse) selector in the center position.

To attach the battery pack:
Align the raised rib on the battery pack with the grooves in the tool, and then slide the battery pack onto the tool.

NOTICE: When placing the battery pack on the tool, be sure that the raised rib on the battery pack aligns with the groove in the tool and that the latches snap into place properly. Improper attachment of the battery pack can cause damage to internal components.

To detach the battery pack:

Depress the battery-release button, located on the front of the battery pack, to release the battery pack. Pull the battery pack out and remove it from the tool.

Battery tools are always in operating condition. Therefore, the direction-of- rotation (forward/center-lock/reverse) selector should always be locked in the center position when the tool is not in use or when carrying it at your side.

Direction-of-Rotation (Forward/Center-Lock/Reverse) Selector (Fig. 3)

After tool use, lock the direction-of-rotation selector in the “OFF” position (center-lock) to help prevent accidental starts and possible injury

Your tool is equipped with a direction-of-rotation selector, located above the trigger switch. This selector is designed for changing the direction of rotation of the bit and for locking the trigger in the “OFF” (center-lock) position.
a. Position the direction-of-rotation selector to the far left of the tool to drill holes or drive the screws in.
b. Position the direction-of-rotation selector to the far right of the tool to remove screws.
c. Position the switch in the “OFF” (center-lock) position to help reduce the possibility of accidental starting when the tool is not in use.

NOTICE: To prevent gear damage, always allow the hammer drill to come to a complete stop before changing the direction of rotation.
NOTE: The hammer drill will not run unless the direction-of-rotation selector is engaged fully to the left or the right.

**Variable-Speed Trigger Switch

(Fig. 4)**

Your tool is equipped with a variable-speed trigger switch. The tool can be turned “ON” or “OFF” by depressing or releasing the variable speed trigger switch.
The variable-speed trigger switch delivers higher speed with increased trigger pressure and lower speed with decreased trigger pressure.

Two-Speed Gearbox Switch (Fig. 5

Your tool is equipped with a two-speed gearbox designed for operating at low or high speeds. The slide switch is located on the top of the tool to select either low (marked “1”) or high (marked “2”) speed.
The low speed (1) provides higher torque and slower speeds for heavy-duty work or for driving
screws, drilling large diameters, or tapping threads. Use the low speed for starting holes without a center punch, drilling metals or plastic, drilling ceramics, or in applications requiring a higher torque.
The high speed (2) provides lower torque and faster speeds for lighter drilling work. The high speed is better for drilling wood and wood composites and for using abrasive and polishing accessories.
NOTICE: To prevent gear damage, always allow the tool to come to a complete stop before changing between low speed (1) and high speed (2)

Function Selector and Torque-Adjustment Ring (Fig. 6)

Your tool is equipped with a function selector for various applications. Move the selector depending on your task.
The Drilling function setting will lock the clutch to permit (non-hammer) drilling or driving for heavy-duty work.
The Screw-Driving function setting optimizes the tool for driving screws.
The Hammer Drilling function setting will lock the clutch to permit hammer drilling only.
NOTICE: Do not use the hammer drilling setting for drilling in wood, metal, ceramic, and plastic to prevent the drill/screw bit from being damaged.

Do not adjust the torque or switch functions while the tool is running.

Your tool also features 17 clutch settings for the screw-driving operation . Output torque will increase as the clutch ring is rotated from 1 to 17. When driving a screw, first try torque position 1 and increase until the desired torque is reached.
The proper setting depends on the job and the type of bit, fastener, and material you will be using. In general, use greater torque for larger screws. If the torque is too high, the screws may be damaged or broken. For delicate operations, such as removing a partially stripped screw, use a low torque setting.

WORKLIGHT (Fig. 7)

Your tool is equipped with a WORKLIGHT light, located on the base of the tool. This provides additional light on the surface of the workpiece for operation in lower-light areas.
The WORKLIGHT will illuminate by default when the tool is turned on OR if the WORKLIGHT button is pressed without turning the tool on.
The WORKLIGHT could be turned off manually by pressing the WORKLIGHT button when the tool is not running.

NOTE: WORKLIGHT will turn off automatically after 10 seconds of inactivity if the WORKLIGHT is turned on by squeezing on the variable-speed trigger switch. WORKLIGHT will turn off automatically after 10 minutes of inactivity if the WORKLIGHT is turned on by pressing the WORKLIGHT button.

NOTE: For safety reasons, the WORKLIGHT button is disabled while the tool is running. The WORKLIGHT will rapidly flash when the tool and/or battery pack becomes overloaded or too hot and the internal sensors will turn the tool off. Rest the tool for a while or place the tool and battery pack separately under air flow for cooling.
The WORKLIGHT will flash more slowly to indicate that the battery pack charge is low. Recharge the battery pack.

Installing and Removing Bits (Fig. 8a & 8b)

Do not use the power of the hammer drill while grasping chuck to loosen or tighten the bit. Friction burn or hand injury is possible if attempting to grasp the spinning chuck.

Do not use bits with damaged shanks.

Your tool is equipped with a keyless chuck to tighten or release drill bits in the chuck jaws. The arrow on the chuck indicates the direction in which to rotate the chuck body in order to lock (“CLOSE”) or unlock (“OPEN”) the chuck jaws on the drill bit.
a. Lock the trigger switch “OFF” on the tool by placing the direction-of- rotation (forward/centerlock/reverse) selector in the center position.
b. Remove the battery pack and select the Drill Position “ ”

a. Rotate the chuck body counterclockwise, viewed from chuck end, to open the chuck to approximately the drill bit diameter.
b. Insert a clean bit up to the drill-bit flutes for small bits, or as far as it will go for large bits. Close the chuck by rotating the chuck body clockwise and securely tighten it by hand (Fig. 8a).

To remove the bit:

a. Rotate the chuck body counterclockwise, as viewed from the chuck end, to open the chuck.
b. Remove the bit.

Make sure to insert the drill bit straight into the chuck jaws. Do not insert the drill bit into the chuck jaws at an angle and then tighten the chuck as shown in Fig. 8b. This could cause the drill bit to be thrown from the tool, resulting in possibly serious personal injury or damage to the chuck.

The bit may be hot after prolonged use. Use protective gloves when removing the bit from the tool, or first allow the bit to cool down.

Removable Belt Clip (Fig. 9)

Your tool is shipped with a removable belt clip that can be positioned on the either side of the tool for convenient transportation.

To install the belt clip onto the tool:

a. Remove the battery pack from the tool.
b. Align the rib and the hole of the belt clip with the opening and the threaded hole on the base of the tool, respectively.
c. Insert the screw and securely tighten the screw with a screwdriver (not included).

Integrated Bit Clip (Fig. 10)

Your tool is equipped with an integrated bit clip located on the back of the tool. Use the bit clip to conveniently store hex bits.

Strap Fixing (Fig. 10)

Strap fixing is provided to attach a wrist strap (not included) in order to reduce the chances of dropping your tool. Wrap the strap around your hand when carrying the tool.

Drill Bits

Always inspect drill bits for excessive wear. Use only bits that are sharp and in good condition.
Twist Bits: Available with straight and reduced shanks for wood and light-duty metal drilling. High-speed bits cut faster and last longer when drilling hard materials.
Carbide-Tipped Bits: Used for drilling stone, concrete, plaster, cement, and other unusually hard nonmetal materials. Use continuous, heavy feed pressure when using carbide-tipped bits.

Drilling (Fig. 11)

Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If the operation is dusty, also wear a dust mask.

a. Check that the direction-of-rotation selector is at the correct setting (forward or reverse).
b. Secure the material to be drilled in a vise or with clamps to keep it from turning as the drill bit rotates.
c. Hold the drill firmly and place the bit at the point to be drilled.
d. Squeeze the variable-speed trigger switch to start the drill.
e. Move the drill bit into the workpiece, applying only enough pressure to keep the bit “biting”. Do not force the drill or apply side pressure to elongate a hole. Let the tool do the work.
f. When drilling hard, smooth surfaces, first use a center punch to mark the desired location of the hole. This will prevent the drill bit from slipping off-center as the hole is started.
g. When drilling metals, use light oil on the drill bit to keep it from overheating. The oil will prolong the life of the bit and increase the drilling action.
h. If the bit jams in the workpiece or if the drill stalls, stop the tool immediately. Remove the bit from the workpiece and determine the reason for jamming
There are two rules for drilling hard materials. First, the harder the material, the greater the pressure you need to apply to the tool. Second, the harder the material, the slower the speed should be. If the hole to be drilled is fairly large, drill a smaller hole first, then enlarge to the required size with a larger bit; it’s often faster in the long run than drilling a larger hole initially.

Wood Drilling

For maximum performance, use high-speed steel or brad-point bits for wood drilling.
a. Begin drilling at a very low speed to prevent the bit from slipping off the starting point.
b. Increase speed as the drill bit bites into the material.
c. When drilling “through” holes, place a block of wood behind the workpiece to prevent ragged or splintered edges on the back side of the workpiece (Fig. 12).

NOTICE: Bits may overheat unless they are reversed and pulled out frequently to clear chips from the flutes.

Metal Drilling

For maximum performance, use high-speed steel bits for metal or steel drilling.
a. When drilling metals, use light oil on the drill bit to keep it from overheating. The oil will prolong the life of the bit and increase the drilling efficiency.
b. Begin drilling at a very low speed to prevent the bit from slipping off the starting point.
c. Maintain a speed and a pressure that allow cutting without overheating the bit.
Applying too much pressure will:
– Overheat the drill.
– Wear the bearings.
– Bend or burn bits.
– Produce off-center or irregularly shaped holes.

Masonry Drilling

For maximum performance, use carbide-tipped masonry bits when drilling holes in brick, tile, concrete, etc.

• Maintain a speed and a pressure that allow cutting without overheating the bit or drill.
  Applying too much pressure will:
  – Overheat the drill.
  – Wear the bearings.
  – Bend or burn bits.
  – Produce off-center or irregular-shaped holes.

• Apply light pressure and medium speed for best results in brick.

• Apply additional pressure for hard materials such as concrete.

• You can make an improvised dust collector by taping a folded piece of paper (or a file folder) to a wall, to reduce the amount of dust when drilling in walls (Fig. 13).

• A tennis ball cut in half can serve as a dust collector when drilling in ceilings (Fig. 13).

• When drilling holes in tile, practice on a scrap piece to determine the best speed and
  pressure. To prevent the drill bit from skidding/sliding, first apply two pieces of masking tape to create an “X” shape over the intended drilling spot (Fig. 13). To prevent tile damage, do no trun the tool in hammer drilling setting .

• Begin drilling at a very low speed to prevent the bit from slipping off the starting point.
  

Driving Screws (Fig. 14)

Try to use standard-type screws for easy driving and improved grip Try to use standard-type screws for easy driving and improved grip.
a. Install the correct driver bit.
b. Ensure that the torque-adjustment ring is set to the most suitable setting. If in doubt, start with a low setting and gradually increase the setting as necessary. Do not change the torque setting when the tool is running.
c. Use the correct speed range for the job and initially apply minimal pressure to the variable speed trigger switch. Increase the speed only when full control can be maintained.
d. It is advisable to drill a pilot hole first. This hole should be slightly longer than the screw to be driven and just smaller than the shank diameter of the screw. The pilot hole will act as a guide for the screw and will also make tightening the screw less difficult. When screws are positioned close to an edge of the material, a pilot hole will also help to prevent splitting of the wood.
e. Use a countersinking bit (sold separately) to accommodate the screw head so that it does not protrude from the surface.
f. Keep sufficient pressure on the drill to prevent the bit from turning out of the screw head. The screw head can easily become damaged, making it difficult to drive home or remove the screw
g. To stop the drill/driver, release the trigger switch and allow the tool to come to a complete stop.

Automatic Spindle Lock

The automatic spindle lock allows you to use it as a manual screwdriver. You can give an extra twist to firmly tighten a screw, loosen a very tight screw, or continue working when the battery charge is depleted. For manual screwdriver purposes, the chuck is automatically locked when the tool is off.

MAINTENANCE

To avoid serious personal injury, always remove the battery pack from the tool when cleaning or performing any maintenance.

Service

Preventive maintenance performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard. We recommend that all tool service be performed by a SKIL Factory Service Center or Authorized SKIL Service Station.

General Maintenance

When servicing, use only identical replacement parts. Use of any other parts could create a hazard or cause product damage

Periodically inspect the entire product for damaged, missing, or loose parts such as screws, nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not operate this product until all missing or damaged parts are replaced. Please contact customer service or an authorized service center for assistance.

Chuck Removal (Fig. 15)

The keyless chuck can be removed and replaced.
a. Lock the trigger switch by placing the direction-of-rotation selector in the center position.
b. Open the chuck jaws.
c. Use a screwdriver (not included) to remove the chuck screw by turning it in a clockwise direction.
d. Insert a 5/16-in. or larger hex key (not included) into the chuck of the tool and securely tighten the chuck jaws around the hex key.
e. Tap the hex key sharply with a mallet (not included) in a counterclockwise direction. This will loosen the chuck for easy removal.
NOTICE: The chuck screw has left-handed threads. Attach a new chuck to the spindle and tighten the chuck screw.

Cleaning

The tool may be cleaned most effectively with compressed dry air

Always wear safety goggles when cleaning tools with compressed air. The guard system, ventilation openings, and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through openings.

Certain cleaning agents and solvents damage plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents that contain ammonia.

Storage

Store the tool indoors in a place that is inaccessible to children. Keep away from corrosive agents.

TROUBLESHOOTING

1. Battery pack is depleted.
2. Battery pack is not installed properly.
3. Burned out switch.

|

1. Charge the battery.
2. Confirm that the battery is locked and secured to the tool.
3. Have the switch replaced by an Authorized SKIL Service Center or Service Station.

Bit cannot be installed.|

1. Chuck is not released.
2. Bit does not fit the chuck.

|

1. Release the chuck.
2. Use an appropriate bit or use a suitable adaptor.

Motor overheating| Ventilation slots are obstructed.| Clean and clear the ventilation slots. Do not cover the slots with hand during operation.
WORKLIGHT flashes rapidly.|  The tool has stopped working to protect internal electronics.| Release the trigger switch, wait for the tool to cool down, then and start the tool again.
WORKLIGHT flashes slowly.| The battery charge is very low.| Charge the battery.

LIMITED WARRANTY FOR SKIL CONSUMER TOOLS

5 YEAR LIMITED WARRANTY

Chevron North America, Inc. (“Seller”) warrants to the original purchaser only, that all SKIL consumer TOOLS will be free from defects in material or workmanship for a period of five years from date of purchase, if original purchaser registers the product within 30 days from purchase. BATTERIES AND CHARGERS are warranted for 2 years. Product registration can be completed online at www.Registermyskil.com. Original purchasers should also retain their receipt as proof of purchase. THE FIVE-YEAR WARRANTY PERIOD FOR TOOLS IS CONDITIONED ON REGISTRATION OF THE PRODUCT WITHIN 30 DAYS OF PURCHASE.

If original purchasers do not register their product timely, the foregoing limited warranty will apply for a duration of three years for tools. All batteries and chargers will remain under the two-year limited warranty

Notwithstanding the foregoing, if a SKIL consumer tool is used for industrial, professional or commercial purposes, the foregoing warranty will apply for a duration of ninety days, regardless of registration SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall be the repair or replacement of parts, without charge, which are defective in material or workmanship and which have not been misused, carelessly handled, or repaired by persons other than Seller or Authorized Service Station. To make a claim under this Limited Warranty, you must return the complete product, transportation prepaid, to any SKIL Factory Service Center or Authorized Service Station. For Authorized SKIL Power Tool Service Stations, please visit www.Registermyskil.com or call 1-877-SKIL-999 (1-877-754-5999).
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS CIRCULAR SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW BLADES, SANDING BELTS, GRINDING WHEELS AND OTHER RELATED ITEMS.

ANY IMPLIED WARRANTIES APPLICABLE TO A PRODUCT SHALL BE LIMITED IN
DURATION EQUAL TO THE DURATION OF THE EXPRESS WARRANTIES APPLICABLE TO SUCH PRODUCT, AS SET FORTH IN THE FIRST PARAGRAPH ABOVE. SOME STATES IN THE U.S., SOME CANADIAN PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS) ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S. AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSOHAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE TO PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY.

THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS SOLD WITHIN THE UNITED STATES OF AMERICA, CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL SKIL DEALER OR IMPORTER.

References

• Log In to Your Owner Account | SKIL
• Innovative Tools with Tech You Can Use |SKIL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>