GE 24LED-7MMb LED 750 7MM LIGHTS Instructions
- June 9, 2024
- GE
Table of Contents
LED 750 7MM LIGHTS
MODEL NO. 24LED-7MMb-750(0.17)
FOR INDOOR USE ONLY
IMPORTANT SAFETY INSTRUCTIONS
When using electrical products, basic precautions should always be followed
including the following:
a) READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b) Do not use seasonal products outdoors unless marked suitable for indoor and
outdoor use. When products are used in outdoor applications, connect the
product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not
provided, contact a qualified electrician for proper installation.
c) This seasonal use product is not intended for permanent installation or
use.
d) Do not mount or place near gas or electric heaters, fireplaces, candles or
other similar sources of heat.
e) Do not secure the wiring of the product with staples or nails, or place on
sharp hooks or nails.
f) Do not let lamps rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, when retiring for the night, or
if left unattended.
h) This is an electric product-not a toy! To avoid risk of fire, burns,
personal injury and electric shock it should not be played with or placed
where small children can reach it.
i) Do not use this product for other than its intended use.
j) Do not hang ornaments or other objects from cord, wire, or light string.
k) Do not close doors or windows on the product or extension cords as this may
damage the wire insulation.
l) Do not cover the product with cloth, paper or any material not part of the
product when in use.
m)This product is equipped with push-in type lamps. Do not twist lamps.
n) Read and follow all instructions that are on the product or provided with
the product.
o) SAVE THESE INSTRUCTIONS
USE AND CARE INSTRUCTIONS
a) When the product is placed on a live tree, the tree should be well
maintained and fresh. Do not place on live trees in which the needles are
brown or break off easily. Keep the tree holder filled with water.
b) If the product is placed on a tree, the tree should be well secured and
stable.
c) Before using or reusing, inspect product carefully. Discard any products
that have cut, damaged, or frayed wire insulation or cords, cracks in the
lampholders or enclosures, loose connections, or exposed copper wire.
d) When storing the product, carefully remove the product from wherever it is
placed, including tree, branches, or bushes, to avoid any undue strain or
stress on the product conductors, connections, and wires.
e) When not in use, store neatly in a cool, dry location protected from
sunlight.
USER SERVICING INSTRUCTIONS
Replace the lamp.
- Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling cord.
- Pull lamp and plastic base straight out of lampholder.
- Replace lamp with only 3.3 Volt, 0.066 Watt, LED type lamp (provided with product).
If the new lamp base does not fit in lampholder, follow the steps below step
3.
a) Remove the base of burned out lamp by straightening lamp leadsand gently
pull lamp out.
b) Thread leads of new lamp through holes in old base with one lead in each
hole.
c) After lamp is fully inserted into base, bend each lead up, like other lamps
in the light set so that the leads will touch the contacts inside the
lampholder.
CAUTION:
- Replace lamps only with 3.3 volt, 0.066 watt spare lamps provided with this product.
- Risk of fire. This product does not contain lamp shunts, which allow the product to operate if one lamp burns out. Do not replace lamps with other than the spare lamps provided with this product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- ncrease the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
TROUBLESHOOTING
| PROBLEM | POSSIBLE CAUSE | CORRECTIVE ACTION |
|---|---|---|
| If the product does not light | One or more of the based LEDs may have loosened |
from the socket during transporting. There is a break in the circuit between
the LED leads and the socket terminals. Male/female connectors not fully
inserted together. Non working control box. Foot pedal in off position.|
Unplug the set at the outlet. Starting with the first unlit LED, gently push
(don’t twist) each LED base firmly into the socket. If still does not light,
then remove each based LED and check for out of place lead wires. Make certain
connectors fully inserted and securing cap fully tightened. Step on foot pedal
to turn LEDs on.
If a based LED is missing| One or more of the based bulbs may have come out of
the socket when transporting.| Mark socket(s) with a piece of tape and unplug
the set. Replace the based LED or use one of the spare based LEDs included
with product.
If an LED fails to light
(shorts or opens)| Incorrect LED, premature LED failure or voltage is too
high.| The LED may be out or dimly lit. Replace bad LEDs as soon as you find
them.
LEDs fail to switch from white to multi| If applicable, then a defective
control box or color change foot pedal.| Contact Customer Support.
For questions and /or assistance, call customer service at
1-877-398-7337 or visit us on the web
at www.geholidaylighting.com
©2022 Nicolas Holiday Limited FP-22 PRINTED IN CHINA
246 Spring Hill Road, Unit B, Trumbull CT 06611
9F., No. 37, Guangfu North Rd. Taipei, Taiwan 10560
All rights reserved.
GE is a trademark of General Electric Company and is under license by
Nicolas Holiday Limited
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>