VOLLRATH 15002 Commercial Food Processor Instruction Manual
- June 1, 2024
- VOLLRATH
Table of Contents
VOLLRATH 15002 Commercial Food Processor
Specifications
- Model: Tabletop and Wall mount models available
- Blade Type: Sharp cutting blade assembly
- Material: Stainless steel construction
- Dimension s: Varies based on model
- Weight: Varies based on model
Product Usage Instructions
Remove the Pusher Head Assembly
Follow the specific instructions based on your model:
- For Tabletop models: Slide the pusher head off the rodguides.
- For Wall mount models: Remove the locking pin, lift the handle, and slide the pusher head off the guide rods. Ensure to place the pin back into the handle assembly.
Raise Bumpers
Raise the bumpers approximately 2 inches (5.0 cm) above the
base.
Remove Blade Assembly
Loosen the thumbscrew and carefully remove the blade assembly by
pressing upwards on the side of the blade holder. Discard the old
blade assembly.
Install New Cutting Blade Assembly
Insert the tab on the blade holder into the groove in the base,
then lower the blade holder into position and tighten the
thumbscrew securely.
Reassemble Pusher Head Assembly
- Slide bumpers down guide rods to contact the base assembly.
- Position the pusher head assembly onto the guide rods, ensuring proper alignment with the blade.
Lubricate Guide Bar
After each use, lubricate the guide bar with mineral oil or petrol gel to
maintain smooth operation. Avoid using cooking oil as it may damage the
equipment.
Installation Instructions
WARNING: Sharp Blade Hazard
Blades are sharp and can cause cuts and amputation.
To avoid injury from sharp blades, handle with caution. Only trained personnel
should operate equipment or perform maintenance.
Wash new blades with warm, soapy water and rinse thoroughly to remove the thin protective oil film. Keep the sharp edge away from you when handling blades.
-
Remove the pusher head assembly:
Tabletop models: Slide the pusher head off the rod guides.
Wall mount models : Remove the locking pin (J). Lift the handle and slide the pusher head off the guide rods. Place pin back into the hole on the handle assembly to prevent loss.
- A Guide Rods. Guides and align the pusher head onto the blade set.
- B Handle. Used to lower and raise the pusher head block
- C Guides. Used for smooth and consistent operation of pusher head on the guide rods
- D Pusher Head Assembly. Made up of the pusher head block (and “T” handle for tabletop models).
- E Bumpers. Cushions the stop of the pusher head.
- G Pusher Head Bock. Pushes the food product through the blade set. Specifically sized to match the corresponding blade assembly.
- H Blade Assembly. Houses the blades. Specifically sized to match the corresponding pusher head block
- I Base Assembly. Holds the guide rods and blade assembly.
- J Locking Pin. Secures the pusher head to the handle.
-
Raise the bumpers approximately 2” (5.0 cm).
-
Loosen thumbscrew and carefully remove the blade assembly. Remove the cutting blade assembly by pressing upwards on the bottom of the side of the blade holder, where the thumbscrew is located. Discard the old blade assembly.
-
Install the new cutting blade assembly by inserting the tab on the blade holder into the groove in the base, then lowering the blade holder into the seated and flush position in the base. Tighten the thumbscrew.
-
Slide bumpers down guide rods to contact base assembly. Position the pusher head assembly onto the guide rods, slowly lower the pusher head assembly, and check the pusher head block to blade alignment.
-
Lubricate the guide bar with mineral oil or petrol gel after each use. Do not use cooking oil as it will become sticky and may permanently damage the equipment.
The Vollrath Company, L.L.C.
1236 North 18th Street
- ADDRESS: Sheboygan, WI 53081-3201 U.S.A.
- Main Tel: 800.624.2051 or 920.457.4851
- Main Fax: 800.752.5620 or 920.459.6573
- Customer Service : 800.628.0830
- Canada Customer Service: 800.695.8560
Technical Services
- techservicereps@vollrathco.com
- Induction Products: 800.825.6036
- Countertop Warming Products: 800.354.1970 All Other
- Products: 800.628.0832
© 2016 The Vollrath Company L.L.C.
Part No. 2350079-1 en 1/22/16
FAQ
- Q: How often should I replace the cutting blade assembly?
- A: It is recommended to replace the cutting blade assembly when you notice a decrease in cutting efficiency or blade sharpness. Regularly inspect the blades for any signs of wear and tear.
- Q: Can I wash the blade assembly in a dishwasher?
- A: It is not recommended to wash the blade assembly in a dishwasher as it may affect the sharpness and longevity of the blades. Hand wash with warm, soapy water and rinse thoroughly for maintenance.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>