DRAPER Clutch Operated FlexShade NEXD Instructions

June 4, 2024
DRAPER

DRAPER Clutch Operated FlexShade NEXD LOGO

DRAPER Clutch Operated FlexShade NEXD

Please check all appropriate selections and attach room schedule with verified dimensions.

DRAPER Clutch Operated FlexShade NEXD 01

Available Sizes

Default small slim available

Small endcaps/brackets and 1 9/16 (40mm) roller are recommended

Large endcaps/brackets and 3 (76mm) roller may be required

Child Safety Information
ANSI/WCMA A100.1-2018 standard (developed by the Window Coverings Manufacturer’s Association and the Consumer Product Safety Commission) was established on December 15, 2018, to eliminate strangulation hazards for small children from hanging cords and chain loops. When dealers specify that custom shades comply with ANSI/WCMA A100.1-2018, Draper provides a pre-installed Spring Loaded Chain Tension Device shown at right for clutch-operated units. When properly installed, tension device prevents creation of a hazardous loop by maintaining tension on bead chain. If not installed properly, shade is partially inoperable. For more information, please see ANSI/WCMA A100.1-2018 compliance www.draperinc.com/windowshades/wcmacompliance.aspx

Specifications

EQUIPMENT

NEXD CLUTCH OPERATOR Delrin POM thermoplastic with swedged 354 (9 mm) primary steel post with rotational bearing to ensure smooth and quiet operation. Overrunning design. Positive mechanical engagement of drive mechanism to tube. White (standard) or black color options. Stainless steel bead chain standard.Ivory, grey, black, white, and brown polyester chain available.

OPTIONAL SPRING ASSIST IDLER

Adjustment free system includes

spring assist components to reduce lifting forces required to raise the shade. Manufacturer shall provide estimated torque for shade unit. Spring-assist is recommended on estimated non-spring-assist torque above 6 lb-in; required on shades with an estimated torque higher than 15 lb-in.

ROLLERS

Extruded aluminum 1 9/16, 2.36, or 3.12 (40, 60, or 79mm) diameter roller tube as appropriate for shade.

COMPONENTS

ENDCAPS **

**

1018 steel stamping. Two sizes available

SMALL

3 7/8 x 3 3/8 (98 x 86 mm)

LARGE

4 5/8x 4 5/8(117 x 117 mm).

Installs to face, ceiling, or jamb. Field convertible between wall left, wall right, or ceiling mount. Idler endcaps to have leveling adjustment.

ENDCAP COVER

Plastic covers push into endcaps for positive engagement. Available in ivory, bronze, black, silver, or white to match fascia.

HEM BAR
  • CLOSED POCKET ELLIPTICAL SLAT: 1 (25mm) aluminum elliptical slat inside of a 1 5/8 (41mm) pocket with heat sealed ends.
  • OPEN POCKET ELLIPTICAL SLAT: 1 (25mm) aluminum elliptical slat with plastic ends inside of a 1 5/8 (41mm) pocket.
  • FLAT EXPOSED HEM BAR: SMALL: 7/8 x 5/16 (22mm x 8mm)
  • LARGE: 1½ x 5/16 (38mm x 8mm) aluminum rectangular hem bar with plastic endcaps.
  • Powder coated in black, bronze, ivory, white, or clear anodized.
FABRIC ATTACHMENT

Spline fabric attachment (standard) allows removal of fabric panel without removal of roller assembly. LSE adhesive fabric attachment available upon request.

FASCIA

L-shaped cover of 6063-T5 extruded aluminum. Fascia snaps into place using no exposed fasteners. Clear anodized finish (standard) or available in ivory, bronze, black, or white powder coat.

SURFACE HEADBOX

Consists of fascia, L shaped back/top cover. Endcaps slide into extrusion without exposed fasteners.

POCKET HEADBOX

For pocket installation, includes a U shaped back/top/front cover with removable bottom closure panel.

  • Small Size: 3 7/16 x 3 15/16 (87 x 100 mm)
  • Large Size: 4 11/16 x 4 11/16  (119 x 119 mm).
  • Some exposed fasteners required.
TYPE D POCKET

Type D Shade Pocket, extruded aluminum, for perimeter installation. Accepts FlexShade installed with endcaps. Finished in white paint 5 x 5 3/8 x .125 (127 x 137 x 3 mm) with 7/8 (22 mm) tile support lip & removable bottom closure.

LIGHT GAP REDUCTION HARDWARE

Extruded aluminum. Accepts edges of fabric, prevents light gaps. Interior of channel provides for use of flat head screws. Available with or without lining.

  • L ANGLE: ¾ x 1 x 12’3 (1.9×2.5x373cm) 1 x 2 ¾ x 16 (2.5x7x488cm) or cut to length.
  • U CHANNEL: 1 x 2 ½ x 16 (2.5×6.4x488cm) or cut to length.
  • H CHANNEL: 1 x 5 x 16 (2.5×12.7x488cm) or cut to length.
  • VINYL L ANGLE: 1 1/2 x 3/4 x 8 (3.81×1.9×243.84cm) stock length only. Installed using adhesive.

DOWNLOADABLE 3-PART SPECIFICATIONS available at www.draperinc.com

Mounting Hardware Selections

Please Note
Endcaps have the only attachment points for mounting a manual FlexShade . Optional fascia and headbox have a thickness of 1/16 (1.6mm).

Endcaps Only Wall Mount
Endcaps Only Ceiling Mount
Fascia Only with Ceiling or Wall Mounting Endcaps

DRAPER Clutch Operated FlexShade NEXD 6

Headbox Installation Options

Surface Headbox Consists of
  • Fascia
  • Back/Top Cover
  • Ceiling/Wall Endcaps
Pocket Style Headbox  Consists of
  • Extruded Pocket
  • Bottom Closure Panel
  • Ceiling/Wall Endcaps
  • SMALL SIZE: 3 7/16 x 3 15/16 (87 mm x 100 mm)
  • LARGE SIZE: 4 11/16 x 4 11/16 (119mm x 119 mm)
Type D Pocket Consists of
  • Extruded aluminum pocket.
  • A lip supports lay-in ceiling.
  • Pre welded corners and ends available.
  • Ends with or without tile support lip.
Typical pre welded corner section not to scale

DRAPER Clutch Operated FlexShade NEXD 9

Clutch Operated FlexShade  NEXD, Small and Large Hardware

Wall Clip and Closure Options

Closure Options

DRAPER Clutch Operated FlexShade NEXD 11

Wall Clip Options

With Tile Lip
Without Tile Lip

Mounting Hardware Selections

Spline Fabric Attachment
U Channel
L Angle
H Channel

Components Small Hardware shown

DRAPER Clutch Operated FlexShade NEXD 18

TOP DOWN VIEW

Shade Width

DRAPER Clutch Operated FlexShade NEXD 19

FRONT VIEW

DRAPER Clutch Operated FlexShade NEXD 20

FlexShade NEXD Endcaps & Fascia

| ENDCAPS
---|---
SMALL| LARGE
A| 3 7/8 98mm| 4 5/8 117mm
B| 3 3/8 86mm| 4 5/8 117mm
C| 2 3/4

70mm

| 3 15/16″ 100mm
D| 2 1/8 54mm| 3 7/16 87mm
E| 1/16 2mm| 1/16

2mm

F| 1 1/4 32mm| 1 1/4 32mm

ENDCAPS WITH FASCIA

SMALL| LARGE
3 7/8 98mm| 4 5/8 117mm
3 3/8 86mm| 4 5/8 117mm
2 3/4 70mm| 3 15/16 100mm
2 1/8 54mm| 3 7/16 87mm
1/16 2mm| 1/16 2mm
1 1/4 32mm| 1 1/4 32mm

HEADBOX WITH ENDCAPS

SMALL| LARGE
3 15/16 100mm| 4 11/16 119mm
3 7/16 87mm| 4 11/16 119mm
2 3/4 70mm| 3 15/16 100mm
2 1/8

54mm

| 3 7/16 87mm
1/16 2mm| 1/16 2mm
1 1/4 32mm| 1 1/4

32mm

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals