Silent Call Medallion Series MC Vibra-Call 3 Receiver User Manual

Medallion Series MC VIBRA-CALL 3TM RECEIVER
INSTALLATION AND OPERATIONS MANUAL
VC4003-MC

Installation and Operations manual
Medallion Series MC 418 MHz VIBRA-CALL 3 Receiver and Docking Port
Model # VC4003-MC

General

The Vibra-Call 3 is a body-worn battery-operated alerting device that includes the Vibra-Call 3 Docking Port equipped with battery backup. It can be used with any Silent Call Medallion Series MC 418 MHz transmitter. The transmitters available are the Sound Monitor, Telephone, Doorbell, Smoke Detector, CO Detector, Fire Alarm Transmitter, Door/Window Access, Weather, and Pressure Sensitive Door or Bed Mat.

Installation

Installing the Vibra-Call 3 receiver and Docking Port consists of locating it where it can be seen most effectively for the user. If using the optional Bed Vibrator or Strobe Light then place the Docking Port on a table or nightstand near your bed.

• Plug the power supply into the DC barrel-type female jack on the back of the Docking port (See locations below) and then into any standard household 120v AC outlet.
• Turn the power switch to the on position.
• If using the optional Bed Vibrator or Strobe Light, then plug those into the corresponding locations on the back of the Docking Port.

Charging/Operation

You will need to charge your Vibra-Call 3 receiver for 8 hours prior to the first use.

• Place the receiver into the Docking port. (If using the Leather Pouch you must remove it before placing the receiver into the Docking Port. If using the optional Rubber Skin you can leave that on the receiver when placing it into the Docking Port.)
• The Receiver will vibrate to let you know that it has been placed into the Docking port properly.
• When the receiver is in the Docking port and detects a signal from a Medallion Series MC 418 MHz transmitter with a matching coding system, it activates the Docking Port’s optional bed vibrator and/or strobe light.
• The vibrator or strobe light will continue for approximately 15 seconds after the transmitted signal ceases except in the case of fire. As long as the Smoke Detector and/or Fire Alarm Transmitters continue to send an alert signal, the Vibra-Call 3 receivers alerting mechanisms will remain on.
• The Vibra-Call 3 has 6 different vibration alerts to tell you which type of transmitted signal was sent; Sound, Phone, Door, Weather, CO, and Fire.
• During the day, take the Vibra-Call 3 receiver out of the Docking Port and clip it to your belt using the provided leather pouch or place the unit into your pocket.

Vibrator Output Pulses

The Vibra-Call 3 receiver has specially defined vibrator output pulses for each type alert signal received. (See the Reference Guide below).
Alarm Vibration Reference Chart And Switch Designation:

Battery Backup Mode

In the event of a power failure, the Vibra-Call 3 Docking Port will automatically enter into battery backup mode. Note: Programmed transmitter codes are retained in memory even when the power is removed.

Last Alert Signal Recall Buttons

To recall the last sent signal, press each of the six buttons on the top side of the Vibra-Call 3 receiver, one at a time. The receiver will initiate a single vibration only when you press the button that identifies which transmitter sent the signal.

Erase memory
(Performing an erase will remove all learned transmitter codes from your Vibra-Call 3)

• With the Vibra-Call 3 receiver in the Docking Port press and hold the learn button on the Docking port. (see photo on page 2)
• Hold down the program button and the receiver will vibrate once. Continue to hold down the button.
• After 4 seconds the receiver will initiate 2 short vibrations, continue holding the program button and after another 6 seconds, the receiver will initiate 3 short vibrations.
• Release the program button and all previously learned transmitter codes will have been successfully erased.

Programming

(If you are using a smoke detector or fire transmitter with the Vibra-Call 3 you must program these transmitters first or the supervision will not operate.) On the rear of the Docking Port is a programming button used to program the Medallion Series MC 418 MHz transmitters to the Vibra-Call 3 receiver. With the Docking Port power switched on, and the Vibra-Call 3 placed in the Dock:

• Press and hold the program button located at the back of the Docking Port case. The Vibra-Call will vibrate once, pause for approximately 5 seconds and then vibrate twice. The unit is now in program mode.
• Release the program button and the unit will remain in program mode for approximately 30 seconds. While in program mode, the receiver will memorize the code of the transmitter and then exit program mode.
• While the receiver is in program mode, press the button on any Silent Call Medallion Series MC 418 MHz corresponding type transmitter. When the receiver receives the transmitted signal, it will memorize the code, and exit program mode automatically.
• Remove the Vibra-Call 3 from the Dock, activate the transmitter previously programmed and the receiver will vibrate as indicated by the Alarm Reference Chart.

Optional Accessories

Optional accessories for the Vibra-Call 3 receivers include:

• 3 pack of protective rubber skins ­Model # Skins
• Replacement leather Pouch-Model # LP-12

Product Specs
Frequency: 418 MHz
Main Power: Input AC 120v
Output 17.2VDC 0.8A, 13.7W Port
Battery Backup: 12 VDC, 350 mAh
Receiver Batteries: (2) AAA rechargeable Batteries
Current Draw: Idle 15 mA, Alert Condition ­ all alert mechanisms active 150 mA.

Technical Support

For technical support on this or any other Silent Call product, please feel free to contact us. You can reach us at our toll-free number phone at 800-572-5227 (voice or TTY) or by Email at support@silentcall.com.

Limited Warranty

Your Vibra-Call 3 is warranted to be free of defects in material and workmanship for five years from the date of initial purchase. During that time, the unit will be repaired or replaced free of charge when shipped prepaid to Silent Call Communications. This warranty is void if the defect is caused by customer abuse or neglect. Batteries are not warranted.

5095 Williams Lake Road, Waterford
MI 48329 248-673-7353 v/tty 248-673-7360 fax 800-572-5227 v/tty
Email: silentcall@silentcall.com
Website: www.silentcall.com

References

• Home And Commercial Alerting Products And Systems

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>