arte confort Novelties Ceiling fans Instruction Manual

: June 2, 2024
: arte confort

arte confort Novelties Ceiling fans Instruction Manual

THANKS FOR TRUSTING IN ARTECONFORT

Congratulations, you love just purchased on Arteconfort ceiling fan: cutting edge technology combined with the Fig test energy efficiency.

WARNING

Read this instruction manual carefully before beginning installation and save it for future reference. In case of transfer of the device, you must also give this instruction manual to the corresponding person.
While using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury.

CAUTION

The product must only be installed by an authorized electrician and in compliance with local, regional and state electricity regulations.
Check if the electrical specifications of this device are compatible with your installation.
Turn off the power before installing or repairing the fan.
The fan must be properly grounded to avoid the risk of electric shock.
Use and unauthorized technical modifications could suppose a risk of injury.
The fan must be connected to a 230V 50Hz power supply.
Do not connect the fan motor to a current dimmer. It could give unsatisfactory performance (engine humming) and cause engine damage.
Be careful while working near the spinning blades.
Do not connect the fan motor to a current dimmer. It could give unsatisfactory performance (engine humming) and cause engine damage.
Be careful while working near the spinning blades.
Never connect the fan to o power point but to the ceiling itself.
The fan must be installed so that the blades are at least 2,3 meters above the ground.
The fan must be hung from a structure capable of supporting a weight of at least 50 kg. The fixture must be able to support the weight of the fan in motion and should not wobble or loosen.
Make sure that the blades do not come in contact with any object at the installation site. Always leave a minimum clearance of 50cm from the tip of the blades to the wall or ceiling.
Keep in mind that the larger this space, the better the fan’s air flow will be.
This device is designed for indoor use only. Do not use in an open space or where it may be exposed to water or moisture.
Never install the appliance in a room with a high degree of humidity.
The fan must not be started in a room with a gas appliance running at the same time. This device can be used by children aged 8 years and above and of people with reduced physical, sensory or mental abilities or lack of experience and knowledge if they are supervised or instructed about the use of the device safely and understand the risks involved. As well as cleaning and maintenance of the device.
Children should not play with the device.
Before reversing the direction of rotation of the blades stop the fan completely. This will prevent any damage to the fan motor or controller (if installed).
Do not insert any object into the fan blades while they are rotating. This can damage them and alter the balance of the fan and the device can fall down. After the fan is fully installed make sure all fasteners are securely fastened to prevent any wobbling or falling of the machine.

The instructions and safety regulations in in is manual cannot prevent all conditions and situations that may occur. For obvious reasons, this manual cannot include factors such as caution and care. These factors must be assumed by who installs, maintains, uses and enjoys the product.

BEFORE INSTALLATION

Open the box avoiding the use of blades or cutters” to avoid scratching the fan components.

Unpack the parts handling them carefully so that they do not bend or scratch, and place the motor on a cloth or a soft surface to prevent damage (you can also use the anti-shock foam on the box for this purpose). Never support the motor sideways.

It is advisable to mount the fan on the floor or a surface large enough so that no component falls.

Identify all parts before beginning assembly.

TOOLS NEEDED

Not included. it is recommended that the screwdriver be magnetized.

MAINTENANCE

Over time and due to the natural movement of the fan, some connections may come loose. Check the support connections, brackets and attach the blades twice a year, and make sure they are firm.
Clean the appliance regularly to maintain its appearance as new. To do this, use a soft, lint-free cloth to avoid scratching the finish. Never use water, because it could damage the motor or the wood of the blades.
It is not necessary to grease the fan, since the motor bearings permanently contain lubricant.

WARRANTY

You can check the warranty for this product on its corresponding page at the end of this manual.

ENVIRONMENT

Do not throw electrical appliances into the household waste, use selective collection facilities. Consult local authorities for more information.

PROBLEM SOLVING

Before carrying out the checks detailed below, the fan must be without power supply.

The fan does not start
- Replace the remote control batteries if they are exhausted or not suitoble.
- Check that there are no nearby devices that may be causing interference with the remote or reducing signal reception.
- Resynchronize the remote control.
- Check that the electrical connections are correct (must be carried out by a licensed electrician).
- Check fuses and switches, that the installation has voltage and it reaches the fan.
The fan makes excessive noise while rotating
- Allow a slight separation between the canopy and the ceiling, preventing them from touching directly.
- Check that the fixing screws of the blades, the fixing screws to the roof, the stem and the fastening elements are correctly tightened.
- If you replaced the original remote control or receiver, reinstall the supplied ones along with the fan.
The fan wobbles
- Check that the fixing screws of the blades, the fixing screws to the roof, the stem and the fastening elements are correctly tightened.
- Check that the blades are not deformed and follow the blade balancing instructions detailed in this manual.
The air flow is insufficient
- Check that the blades rotate in the correct direction (Summer / Winter).
- Avoid nearby objects that may impede air circulation.
- Verify that the diameter of the blades of your fan is sufficient for the area of the room in which it is installed.
The light does not turn on
- Check the bulb is not blown, otherwise replaces it with a new one.
- If your fan has LED light included, check the connections are properly fixed according to the instruction manual.

BALANCING OF BLADES

The balancing of the fan is not a sign of malfunction. Before balancing, and always with the fan off, check the fastening of the blades and that they do not show deformations. Once checked, if everything is correct, proceed to the balancing of the blades:

Select the blade to balance
Put the clip included in the center of a blade. Next, turn on the fan and, if the balancing persists, put the clip on another blade until the swing decreases. In this way, the selected blade will be the one that needs the counterweight.
Find the equilibrium point
Place the clip on the blade you have previously selected and try the best place to place it (from the center to the tip of the blade) until the wobble disappears.
Check the correct balance
Glue the counterweight to the height of the clip on the surface of the blade. Remove the clip, and turn on the fan. Check if it continues to wobble, if so, place another counterweight. If it gets worse, you should try another better area to place it.

REMOTE CONTROL

FAN ON/OFF
Turn the fan on or off.

LIGHT ON/OFF
Turn the light on or off.

TIMER
Set the hours of operation of the fan (1, 4 or 8 hours).

SPEED
Select the rotation speed of the fan blades.

WINTER/SUMMER MODE (F/R)
Reverse the direction of blades rotation to change to summer/winter mode.

The remote control is synchronized from the factory, you only need to re- synchronize it if the synchronization has been lost, if you purchased a new one or want to control several fans with a single remote.

BATTERIES

The remote control batteries are included. The required battery model is LRV08, 23A, MN21 12V.

*Remove the batteries from the controller if it is not going to be used fora long time.

COLOR TEMPERATURE MEMORY

The fan has color temperature memory of the light. This function allows you to maintain the some color temperature when the fan light is turned on again.

To change the color temperature, turn off the light by pressing the “Lamp ON/OFF button once and turn it on again by pressing the button again within 2 seconds. Turn the light off again by pressing “ON/OFF” and after 15 seconds turn it on again, it will keep the last selected temperature.

REMOTE CONTROL SYNCHRONIZATION

The remote control is synchronized from the factory, you only need to re- synchronize it if the synchronization has been lost, if you purchased a new one or want to control several fans with a single remote.

A REMOTE CONTROL TO A NEW FAN

Cut the current: Be sure to cut off the current until the fan stop.
Restore the current: Re-establish the current.
Synchronize the remote control: Within 5 seconds, press the “FAN ON/OFF” button for a few seconds until you hear the signal. Control range: 8-10m.

A REMOTE CONTROL TO VARIOUS FANS

Cut the current: Be sure to cut off the current until all fans stop.
Restore the current: Re-establish the current.
Synchronize the remote control: Within 5 seconds, press the “FAN ON/OFF” button on each fan for a few seconds until you hear the signal. If they are within a radius of less than 10m (control range: 8-10m), all will synchronize at the same time.

A REMOTE CONTROL TO A FAN

(Example for two fans, applicable to a larger number of fans)

*Cut the fan A current:** Be sure to cut the fan A current (the one we want to remove the synchronization).
*Cut the fan B current:** Be sure to cut off fan B (the one we want to synchronize).
Restore fan B current: When you restore the fan B, press the “FAN ON/ OFF” button within 5 seconds until you hear the signal to synchronize remote control B with fan B.
*Cut the fan B current:** Be sure to cut the fan B current.
Restore the fan A current: When you restore the fan A press the “FAN ON/ OFF” button within 5 seconds until you hear the signal to synchronize remote control A with fan A.
Repeat the steps: Repeat steps with each fan you have and want to individualize its remote control.

*To cut the current you can press the individual fan switch. If there is not, disconnect the quick connect cables from the fan.

Installation Instruction

SPARE PARTS

You can request spare parts by going to the store where you purchased it or to any another of the brand. If the product is under warranty, present the purchase receipt or invoice.

DESCRIPTION	REFERENCE
Light cover	PLAPARIS
LED module	LEDPARIS
Remote control	MANPARISONLY
Driver Controller	CONPARISONLY

WARRANTY

This fan is guaranteed for 3 years. This warranty covers the exchange or repair of any failure or defect of the device, provided that it is due to a manufacturing fault or a defective component.

IMPORTANT: It is essential for the use of this guarantee to prove the purchase date of the product. Therefore, it will be necessary to present the purchase receipt as well as this instruction manual.

Keep the purchase receipt and the instruction manual.

The warranty of this product does not apply if the defects of the device have been caused by:

Damage during transport not carried out by the manufacturer. (Example: dents, components or glass pieces damages …)
Carrying out incorrect installations or assemblies.
Poor preservation of the product.
Damage caused by contact of the device with chemical or inappropriate substances. This fan is designed for indoor use only, so it should not be exposed to water and / or humidity either.
The replacement or use of additional parts or accessories that are not original from the manufacturer.
When using a control through a wall dimmer other than the remote control supplied with the fan.

Before calling for technical assistance, it is advisable to read the troubleshooting guide included in this manual.

Support

If you have any questions, problems or missing components, consult your dealer. You can also contact us through the email [email protected] or through the contact form available on our website.