arte confort PATRI Ceiling Fans Instructions

Instruction Manual

PATRI Ceiling Fans

THANKS FOR TRUSTING IN ARTECONFORT
Congratulations, you have just purchased an Artconfrot ceiling tan. cutting edge technology combined with the highest energy efficiency

WARNING
Read this instruction manual carefully before beginning installation and save it for future reference. In case of transfer of the device, you must also give this instruction manual to the corresponding person.
While using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury.

CAUTION

• The product must only be installed by an authorized electrician and in compliance with local, regional and state electricity regulations
• Check if the electrical specifications of this device are compatible with your installation
• Turn of the power before installing or repairing the fan
• The fan must be properly grounded to avoid the risk of electric shock
• Use and unauthorized technical modifications could suppose a risk ot injury
• The fan must be connected to a 230/ 50Hz power supply
• Do not connect the tan motor to a current dimmer lt could give unsatisfactory performance (engine humming) and cause engine damage Be careful while working near the spinning blades Never connect the fan to a power point but to the ceiling itself
• The fan must be installed so that the blades are at least 2, meters above the ground
• The fan must be hung trom a structure capable of supporting a weight of at least 50 kg The fixture must be able to support the weight of the tan in motion and should not wobble or loosen
• Make sure that the blades do not come in contact with any object at the installation site Always leave a minimum clearance of 50cm from the tip of the blades to the wall or ceiling Keep in mind that the larger this space, the better the fans air flow will be
• This device is designed for indoor use only. Do not use in an open space or where it may be exposed to water or moisture
• Never install the appliance in a room with a high degree of humidity
• The on must not be started in a room with a gas appliance running at the same time
• This device can be used by children aged 8 years and above and of people with reduced physical, sensory or mental abilities or lack of experience and knowledge il they are supervised or instructed about the use ol the device sately and understand the risks involved As well as cleaning and maintenance ol the device
• Children should not play with the device
• To reverse the direction of the blades, do it while moving
• Do not insert any object into the fan blades while they are rotating. This can damage them and alter the balance of the fan and the device can tall down
• After the fan is fully installed make sure all fasteners are securely fastened to prevent any wobbling or falling of the machine

The instructions and safety regulations in this manual cannot prevent all conditions and situations that may occur For obvious reasons, this manual cannot include factors such as caution and care These tactors must be assumed by who installs, maintains, uses and enjoys the product

BEFORE INSTALLATION

Open the box avoiding the use of blades or cutters to avoid scratching the tan components
Unpack the parts handling them carefully so that they do not bend or scratch, and place the motor on a cloth or a soft surtace to prevent damage (you can also use the anti.shock foam on the box for this purpose). Never support the motor sideways is advisable to mount the tan on the floor or a surtace large enough so that no component falls Identity all parts before beginning assembly

TOOLS NEEDED
Not included It is recommended that the screwdriver be magnetized

MAINTENANCE

• Over time and due to the natural movement of the tan, some connections may come loose
  Check the support connections, brackets and attach the blades twice a year, and make sure they are firm

• Clean the appliance  regularly to maintain its appearance as new. To do this, use a soft, lint free cloth to avoid scratching the finish Never use water, because it could damage the motor or the wood of the blades

• It  is not necessary to grease the tan, since the motor bearings permanently contain lubricant

WARRANTY
You can check the warranty tor this product on its corresponding page at the end of this manual

ENVIRONMENT
Do not throw electrical appliances into the household waste, use selective,, collccl,011 foc,l,t,es Consult local authorities tor more information electrical appliances are deposited  in landfills, hazardous components can seep into groundwater and enter the food chain, damaging health and well-being
Thanks tor taking care of the environment

This product contains a light source of energy efficiency class D – (EU) 9019/2015

PROBLEM SOLVING

Before carrying out the checks detailed below, the fan must be without power supply

1. The fan does not start
   • Replace the remote control batteries if they are exhausted or not suitable
   • Check that there are no nearby devices thot may be causing interference with the remote or reducing signal reception
   • Resynchronize the remote control
   • Check that the electrical connections are correct (must be carried out by a licensed electrician)
   • Check fuses and switches, that the installation has voltage and it reaches the fan

2. The fan doesn’t start but the light does.
   • With the fan off, check with your hand that the blades turn freely.

3. The fan makes excessive noise while rotating
   • Allow a slight separation between the canopy and the ceiling, preventing them from touching directly
   • Check that the fixing screws of the blades, the fixing screws to the root, the stem and the fastening elements are correctly tightened
   • If you replaced the original remote control or receiver, reinstall the supplied ones along with the fan

4. The fan wobbles
   • Check that the fixing screws of the blades, the fixing screws to the roof, the stem and the fastening elements are correctly tightened
   • Check that the blades are not deformed and follow the blade balancing instructions detailed in this manual

5. The fan does not give air or the air flow is insufficient
   • Check that the blades are not mounted backwards
   • Check that the blades rotate in the correct direction (Summer / Winter)
   • Avoid nearby objects that may impede air circulation
   • Verity that the diameter of the blades ot your fan is sufficient for the area ol the room in which it is installed

6. The light does not turn on
   • Check the bulb is not blown, otherwise replaces it with a new one
   • If your fan has LED light included, check the connections are properly tixed according to the instruction manual

COLOR TEMPERATURE MEMORY
The fan has color temperature memory ol the light This function allows you to maintain the same color temperature when the fan light is turned on again
To change the color temperature of the light press. the button indicated with the color ot each color temperature
When you turn the light off and turn it on again it will keep the selected temperature

REMOTE CONTROL

WINTER/SUMMER MODE
Reverse the direction of rotation of the blades to change to summer mode or winter mode
ON/OFF LIGHT I SYNCHRONIZATION
Turns the light and synchronization on or off (see section Control synchronization)
ON/OFF FAN
Turn the fan on or off
SPEED REGULATOR
lncreases or decreases the turning intensity ot the blades
LIGHT INTENSITY REGULATOR
lncrease or decrease the intensity ol the light
LCD INDICATOR
Indicates the number ot speeds, trom the bottom of the screen to the top
LIGHT TEMPERATURE
Change the color temperature of the light
PROGRAMMING
Sets the hours of fan operation (1, 2 or 4 hours)
BREEZE MODE
Activate the breeze mode that alternates smoothly between soft and fast speeds (from speed l to 3) to create a greater sensation ot comtort

To activate the breeze mode, activate the ton using the ‘ON/OFF’ button on the fon and then press the Breeze mode button
For cancel breeze mode press the Breeze mode button again, the fan will return to the rotation speed selected betore the breeze mode. You can also press the ‘ON/OFF’button of the fan to completely stop the rotation of the blades, when you turn it on again it will not remember the breeze mode, activating at the previously selected rotation speed
The remote control is synchronized from the factory, you only need to re- synchronize it if the synchronization has been lost if you purchased a new one or want to control several tans with a single remote 

BATTERIES
The remote control batteries are included The required battery model is 2 AAA
Remove the batteries trom the controller if it is not going to be used tor a long time

REMOTE CONTROL SYNCHRONIZATION

The remote is factory synchronized, you only need to resynchronize the remote it you have lost synchronization, purchased a new one, want to control several tans with a single remote, or the fan does not respond to the remote control orders while it is running

A REMOTE CONTROL TO A NEW FAN

1. Cut the current
   Be sure to cut off the current until the tan stop and wait 30

2. Restore the current
   Past 3O re-establish the current

3. Synchronize the remote control Within 10 seconds, press the synchronization button ‘ON/OFF light ( ) during seconds until you hear the signal. Control range. 8.10m
   

A REMOTE CONTROL TO VARIOUS FANS

1. Cut the current
   Be sure to cut of the current until all fans stop and wait 30

2. Restore the current
   Pest 3O re-establish the current

3. Synchronize the remote control
   Within 10 seconds, press the synchronization button “ON/OFF light ( )” on each fan during 3 seconds until you hear the signal. If they are within a radius of less than 10m (control range: 8-10m), all will synchronize at the some time.

A REMOTE CONTROL TO A FAN
(Example for two fans, applicable to a larger number of fans)

1. Cut the fan A current”
   Be sure to cut the tan A current (the one we want to remove the synchronization) and wait 3O

2. Cut the fan B current”
   Be sure to cut off fan B (he one we want to synchronize) and wait 30
   

3. Restore fan B current
   When you restore the fan B and within 10 seconds, press the synchronization button ‘ON/OFF light ( )’ during seconds until you hear the signal to synchronize remote control B with fan B.

4. Cut the fan B current
   Be sure to cut the fan B current and wait 30.
   

5. Restore the fan A current
   When you restore the fan A and within IO seconds, press the synchronization button ‘ON/OFF light ( )’ during b seconds until you hear the signal to synchronize remote control A with fan A.

6. Repeat the steps
   Repeat steps with each fan you have and want to individualize its remote control
   

To cut the current you can press the individual fan switch IF there is not disconnect the quick connect cables from the fan.

PATRI
SYNCHRONISATION OF TWO REMOTE CONTROLS TO A FAN

GENERAL GUIDE: PARTS OF A FAN

SCREW GUIDE

SCREWS FOR THE ROOF

Screws for the roof
Ceiling screw plugs
Washer for ceiling screw

SCREWS FOR BLADES

Screw for wood blades
Screw for blades with washer
Screw for blades
Paper washer for blade screw

SPARE PARTS
You can request spare parts by going to the store where you purchased it or to any another of the brand. If the product is under warranty, present the purchase receipt or invoice

DESCRIPTION

Light cover

LED module

Remote control

Driver

WARRANTY

The fan is guaranteed for 3 years. This warranty covers the exchange or repair ot any tailure or defect of the device, provided that it is due to a manufacturing taut or a detective component

IMPORTANT
It is essential for the use of this guarantee to prove the purchase date of the product Therefore, it will be necessary to present the purchase receipt as well as this instruction manual

Keep the purchase receipt and the instruction manual.

The warranty of this product does not apply if the defects of the device have been caused by

• Damage during transport not carried out by the manufacturer (bxample: dents, components or glass pieces damages) or Incorrect
• Carrying assemblies
• Poor preservation of the product
• Damage caused by contact of the device with chemical or out installations inappropriate substances. This tan is designed tor indoor use only, so it should not be exposed to water and/ or humidity either
• The replacement or use of additional parts or accessories that are not original from the manufacturer
• When using a control through a wall dimmer other than the remote control supplied with the fan Before calling for technical assistance, it is advisable to read the troubleshooting guide included in this manual

wwwarteconfort.com
ARTECONFORT HOTELS L
Ctra Andalucia, 6
459224 Seseha Nuevo
Toledo, Espana

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>