COSTWAY NP10261CF 32 in.x 20 in Propane Rattan Fire Pit Table User Manual

COSTWAY NP10261CF 32 in.x 20 in Propane Rattan Fire Pit Table

Contact Us!
Do NOT return this item.
Contact our friendly customer service department for help first.

Before You Startefore You Start

• Please read all instructions carefully. Retain instructions for future reference. Seperate and count all parts and hardware. Read through each step carefully and follow the proper order.
• We recommend that, where possible, all items are assembled near to the area in which they will be placed in use, to avoid moving the product unnecessarily once assembled.
• Always place the product on a flat, steady and stable surface.
• Keep all small parts and packaging materials for this product away from babies and children as they potentially pose a serious choking hazard.

WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage,personal injury,or loss of life.

DANGER: FIRE OR EXPLOSION HAZARD If you smell gas:

• Shut off the gas to the appliance.
• Extinguish any open flame.
• If the odor continues, leave the area immediately.
• After leaving the area, call a professional or fire department.

Failure to follow these instructions could result in fire or explosion, which could cause property damage, personal injury, or death.

WARNING For outdoor use only.
Installation and service must be performed by a qualified installer and qualified technician.

WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information consult a qualified installer and qualified technician.

Before you assemble or operate this unit, please carefully read this entire manual. Failure to do so may result in a fire, explosion, injury or death.

WARNING

• The installation of this unit must adhere to local codes or Propane Storage and Handling Code, CSA B149.2.
• THIS UNIT IS INTENDED FOR OUTDOOR USE ONLY! This product shall be used outdoors, in a ventilated space and shall not be used in any enclosed area.
• This unit is to be used with propane gas only! (sold separately)
• Do not attach a remote gas supply to this unit.
• Only use propane gas for this unit.
• Solid fuels shall not be burned in this appliance.
• When igniting this unit, stay away from the burner as the flame will light up and may cause injury.
• LP GAS WARNING: Do not use any more than 1/4in（0.635 cm） depth lava rocks/pumice stones/L avaGlass® above the burner holes. Doing so will suffocate the flame.
• If the propane gas tank is leaking gas, you may hear, see, or smell a hiss. Do the following:
  1. Disconnect the propane gas tank.
  2. Do not attempt to fix the problem yourself.
  3. Contact a professional or fire department for help.
• Applying too much propane may result in gas pooling and will not burn. Allow fresh air into the unit so that the remaining gas may escape.
• Do not use a flame to check for gas leaks.
• Manifold pressure: 11 inch w.c. (2.74kPa).
• Use LP propane tanks with the following dimensions: diameter 12 in/ 30 cm, height 18 in/ 46 cm – capacity 20 lbs/ 9 kg.
• You must use a propane tank that has a collar to protect the gas valve.
• DO NOT fill tank over 80 percent full.
• The tank system must be set up for vapor withdrawal.
• Discontinue use if any part of the propane tank is damaged. Rust and dents may be hazardous and should be inspected by a gas supplier.
• Do not burn anything other than the provided materials for this fire table.
• Keep away from the unit for the first 20 minutes after igniting your unit for the first time, as lava rocks/pumice stones/L avaGlass@ could pop out and cause injury.
• Should any rocks pop out, discard them.
• Always ensure that lava rocks/pumice stones/L _avaGlass are completely dry before use. Failure to do so will cause them to crack or pop.
• Do not operate unit until all parts are fully assembled.
• Do not paint or color any part of this heating unit.
• Unit may be hot while in use, do not attempt to move it while in use.
• Never leave this heating unit unattended while in use.
• This unit is not intended for cooking.
• Keep any flammable items away and do not use any other fireplace cover for this unit.
• Keep a safe distance to avoid burning skin or clothing.
• Do not sit or rest hands or feet on this heating unit.
• Never place hands or fingers on upper portion of this unit while in use.
• Keep all electrical cords and fuel supply hose away from heated surfaces.
• Combustible material should not be within 60 inches/ 152.4 cm of the top of the unit, or within 48 inches/ 121.9 cm around the entire unit.
• Keep the appliance area clear and free from combustible material, gasoline and other flammable vapors and liquids.
• If the flame goes out while burning, turn the gas valve off. Wait 5 minutes before repeating the initial lighting procedure. Once you have a flame started, hold down the control knob for 1 minute.
• Do not add water into the unit.
• Do not operate unit if any part has been underwater. Immediately call a qualified service technician to inspect the appliance and replace any part of the control system and any gas control that has been under water.
• Do not disconnect any part while unit is in use.
• Do not store a spare propane tank on or near this unit.
• If the heating unit is indoors, detach the propane tank and leave outdoors.
• Do not operate on a boat or vehicle. This unit must be used on a flat surface and outdoors ONLY.
• Always remove protective cover before operating (f applicable).
• Do not set the protective cover over the unit until it is turned off and completely cooled down.
• Check for leaks after not using the unit for long periods of time.
• Children should never operate this unit. Children must be supervised while near this unit.
• Keep gas tank at least 5 feet/ 152.4 cm away from unit when lit.(if external tank)
• Maximum gas supply: 250 psi; Min. gas supply: 10 psi.
• All installation and repair should be done by a qualified professional. This unit should be inspected annually and cleaned regularly.
• Inspect all elements of this heating unit before each use. If there is damage, the burner must be replaced.
• Keep the hose out from any pathways to eliminate any accidental damage. (f external tank)
• Be aware of the hazards of high temperatures and stay away from the unit to avoid any burns or injury.
• The gas supply tank should be constructed and marked with the specifications for the LP gas tanks of the U.S. Department of Transportation or the National Standard of Canada CAN/CSA- B339, LP gas tanks, spheres and tubes for Transportation of Dangerous Goods; and Commission.
• The LP gas tank must have a listed overilling prevention device and a QCCI or Type , (CGA791) LP gas tank connection.
• This heating appliance should not be used on plastic or artificial wood decks.
• Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition.
• Young children should be carefully supervised when they are in the area of the appliance.
• Clothing or other flammable materials should not be hung from the appliance or placed on or near the appliance.
• Any guard or other protective device removed for servicing the appliance shall be replaced prior to operating the appliance.
• Installation and repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required as necessary. It is imperative that the control compartment, burners and circulating airways of the appliance are kept clean.

Only use the regulator and hose assembly provided with this unit.
Inspect the bumer before use of this unit. If the burmer shows any kind of damage, do not operate the appliance.

NOTE: You must follow all steps to properly assemble this heating item. Make sure the gas valve is turned“OFF”before assembling. Do NOT attempt to assemble without proper tools.

Combustible materials should not be within 60 inches of the top of the unit, or within 48 inches around the entire unit.

Do not tighten the screws until the assembly is complete.

Installation Instruction

1. Attach panel (D) and the panel (E) to the table top (F) using 4pcs of Bolts (1) and 4pcs M6 washer (4) with Allen Wrench (5). Do no fully tighten.

2. Attach panel (C) with Panel (D) and Panel (E) together using 8pcs Bolts (2) and 8pcs M6 washer (4) with Allen Wrench (5). Do not fully tighten.

3. Attach advjustable foot (G) to the bottom of fire pit using 8pcs of Bolts (3) with Allen Wrench (5). Tighten the bolts.

4. Put the metal lid (A) on the table top of the fire pit. Then tighten all the bolts with the allen wrench.

5. Pour the box of lava rocks into the body of the fire place.
   DANGER: To ensure proper function, the guard on this burner should be free of lava rocks at all times.

6. Remove the rubber cap on the electronic igniter by unscrewing and slide battery (B) into the battery slot. Make sure the positive side of the battery faces outwards. Screw the electronic igniter cap over the battery tightly.

7. Turn the cylinder valve on the tank clockwise to close the propane tank.

8. Attach the pre-assembled regulator from the body to cylinder valve by turning the regulator coupling nut clockwise. Make sure it is fastened securely and tighten connections by hand only.

Before performing a leak test, be sure that no sparks can occur and you are in a spacious outdoor area. Connect the propane gas tank to the regulator and turn the valve on the unit to the “off” position. Brush a soap and water mixture on all connections. Turn the gas supply on; if bubbles occur on any connection there may be a leak. If you smell gas or a leak is discovered turn the gas valve off, disconnect propane gas tank and do not use the appliance until the leak is repaired.
Do not use the heating unit without inspecting the gas hose. If there are signs of wear or abrasion you must replace the hose (if applicable). Pumice stones/lava rocks/LavaGlass® could pop up and strike somebody’s face during the process of lighting this unit; stand away from the unit for the first 20 minutes after igniting. Flame height should be a yellow/blue color between 2 – 10 inches(5.08 – 25.4 cm) in height.
Wait 50 minutes after extinguishing flame prior to placing a lid (if applicable) or protective cover on heating item.

To Light

1. Make sure the control knob is in the “OFF” position.
2. slowly open the valve on the propane gas tank by turning the knob counterclockwise.
3. Push and hold the electronic igniter to create sparks within the electrode, continue to hold.
4. Push in the control knob and turn to the “low” position. Keep holding the control knob to allow gags to flow for 45 seconds.
5. If ignition doesn’t occur within a few seconds, release the control knob and rotate to the “OFF” position. Wait for 5 minutes for gas to clear and then repeat the above lighting instructions.
6. To adjust the flame, turn the control knob either clockwise or counterclockwise depending on whether you want to lower or raise the flame.

To Extinguish

1. Turn the control knob clockwise to the “HIGH” position; push and continue turning the control knob to the “OFF” position.
2. Close the cylinder valve on the propane gas tank if you don’t intend to use it for a long time.

• Before performing any maintenance always disconnect the propane gas tank.
• Store your product indoors during winter months. Avoiding extreme cold temperatures will prevent exposure damage.
• Keep the heating item free and clear from combustible materials.
• Visually inspect the burner for obstructions and keep tank enclosure free and clear from debris.
• Use a soft brush to get rid of the mild stains, loose dirt and soil after the burner and pumice stones/lava rocks/LavaGlass® are completely cooled down. Wipe down with a soft cloth.
• Harsh weather conditions may cause stubborn stains, discoloration and possibly rust pitting.
• Permanent damage may occur if powder or solvent comes in contact with painted or plastic components on this heating unit.
• Keep the heating unit stored away from direct sunlight.
• If storing this unit inside, disconnect the propane gas tank from the gas valve.
• Always place lid (if applicable) or protective cover on heating item when not in use.

1. Attach panel (A) and panel (B) to panel (C) using 4pcs of Bolts (2) and 4pcs M6 washer (3) with Allen Wrench
   (4). Do not fully tighten.

2. Attach panel (D) to panel (A) and panel (B) using 4pcs of Bolts (2) and 4pcs M6 washer (3) with Allen wrench (4). Fully tighten.

3. Attach metal stand (E) to bottom of gas tank cover using 4pcs of Bolts (2) and 4pcs M6 washer (3) with Allen wrench (4). Fully tighten.

4. Attach panel (F) to panel (C) using 4pcs of Bolts (1) with Allen Wrench (4). Fully tighten.

5. After all bolts are tightened, you can use it!

6. Place the 20 lb/ 9 kg. propane gas tank (not included) into the tank holder. Turn the wing screw on the outside of the tank holder clockwise to tighten the tank into the tank holder.

Heating unit won’t light

|

The heating unit won’t light

|

Dry off with a soft cloth

The igniter battery is incorrectly inserted

|

Check in which direction the battery is inserted

Igniter pin is broken

|

Ask qualified technician for help

Electrode wire is loose or disconnected

|

Reconnect wire to the igniter box located inside the fire pit behind the igniter box

Electrode wire is shorting between valve and igniter pin

|

Ask qualified technician for help

Burner won’t light while using a match

| No gas flow| Check that the gas tank isn’t empty

Regulator isn’t connected securely to the tank

|

Tighten regulator connection to the gas tank

Gas flow is obstructed

|

Check all hoses for kinks and bends

Burner ports are clogged

|

Turn all gas flow connections off. Insert an opened paperclip (or similar item) into each of the burner ports to clear them out.

Check that all burner ports are free of any small lava rocks/pumice stones/LavaG lass® pieces|

Flame is obstructed at burner ports

|

Check that all burner ports are free of any small lava rocks/pumice stones/LavaGlass® pieces

Regulator hose is kinked

|

Straighten hose of all bends or kinks

 |

No gas flow

|

Check that the gas tank isn’t empty

Sudden drop in gas flow

|

Excess flow safety valve has been activated

|

Turn the control knob to the ‘off’ posi-tion. Close the tank valve and disconnect propane gas tank. Turn the control knob to ‘high’; wait 1 minute. Turn the control knob back to the ‘off’ position. Recon-nect propane gas tank. Light the fire unit as indicated in the ‘To Light’ section of this manual.

---|---|---
 |

High or gusting winds

|

Increase flame to ‘high’

Flame blows out easily

|

No gas flow

|

Check that the gas tank isn’t empty

Excess flow safety valve has been activated

|

See ‘sudden drop in gas flow’ above

With your inspiring rating, COSTWAY will be more consistent to offer you EASY SHOPPING EXPERIENCE, GOOD PRODUCTS and EFFICIENT SERVICE!

Documents / Resources

| COSTWAY NP10261CF 32 in.x 20 in Propane Rattan Fire Pit Table [pdf] User Manual
NP10261CF 32 in.x 20 in Propane Rattan Fire Pit Table, NP10261CF, 32 in.x 20 in Propane Rattan Fire Pit Table, Propane Rattan Fire Pit Table, Rattan Fire Pit Table, Fire Pit Table, Pit Table
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>