VONN VMC33223 23 Inch Integrated LED Black Chandelier Lighting Fixture Installation Guide

: June 3, 2024
: VONN

Table of Contents

VONN VMC33223 23 Inch Integrated LED Black Chandelier Lighting Fixture
TOOLS YOU MAY NEED
PARTS LIST
LED INFO & WARNINGS
Fixture Diagram
Instructions
Install Mounting Bracket
Connect Wires
Mount Fixture
Turn Power ON
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VONN VMC33223 23 Inch Integrated LED Black Chandelier Lighting Fixture

TOOLS YOU MAY NEED

PARTS LIST

A. Mounting bracket x 1
B. Rubber plug x 4+1
C. Tapping screw x 4+ 1
D. Outlet screw x 2 + 1
E. Wire connector x 2 + 1
F. Ground screw x 1
G. Canopy cover screw x 4

CIRCUIT BOX

LED INFO & WARNINGS

Please read and understand the entire manual before attempting to assemble, operate, or install the product.
All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn or broken.
Please handle the LED light with care when unpacking. Do not apply pressure to the LED’s, do not open any factory sealed compartments, and do not touch the LEDs with your hands.
VONN recommends to install the ﬁxture on its own independent circuit. Do not install the ﬁxture on the same circuit with the other appliances, or HVAC systems.
DO NOT CUT WIRES attached to the ﬁxture under any circumstance. Cutting wires will VOID your warranty. Excess cable should be neatly looped and tucked into the canopy.
Place the wall switch in the “OFF” position of the room you are installing the ﬁxture.
Make sure that you have all necessary parts by checking the parts list. If any part is missing or damaged please contact VONN LIGHITNG CUSTOMER SERVICE at 888-604-8666 for
a replacement.
Inspect the LED ﬁxture prior to installation to make sure that it has not been damaged during shipping.
VONN highly recommends to use a qualiﬁed, licensed electrician to install the ﬁxture.
Do not remove or replace VONN manufactured parts that is provided with the ﬁxture.
VONN recommends ELV (Electric Low Voltage) type dimmers for this ﬁxture.
Shut “OFF” the electricity at main fuse box.

Fixture Diagram

Instructions

Adjust Height

The length of the cable is adjustable. To determine the proper length of the ﬁxture, hold the ﬁxture canopy up against the outlet box in the ceiling to adjust the cable.
Depress locking pin on the canopy, hold pin in place, and pull down or push up on the cable. Repeat step for each cable.
Installer Tip (1): It is recommended that two install-ers are required to adjust the height of the ﬁxture. One installer to hold the ﬁxture, and the second installer to adjust the cables.

Install Mounting Bracket

Connect Wires

Supply Wires:
Connect Black (Line Wire) from ﬁxture to Black (Hot Wire) from outlet box. Connect White (Neutral Wire) from ﬁxture to White (Neutral Wire) from outlet box.

Ground Wires:
Connect Bare Copper (Ground Wire) from ﬁxture to Green or Bare Copper (Ground Wire) from outlet box. Twist wires together clockwise and secure with wire connector (E).

Installer Tip (2): If ground wire is not available in outlet box, then secure Bare Copper (Ground Wire) from ﬁxture to ground screw (F) on mounting bracket (A).

Installer Tip (3): It is recommended that two installers are required to install the ﬁxture. One installer to hold the ﬁxture, and the second installer to connect the wires.