VONN VAC3315 5-Light Integrated LED Black Chandelier Lighting Fixture Installation Guide
- June 3, 2024
- VONN
Table of Contents
VAC3315 5-Light Integrated LED Black Chandelier Lighting Fixture
Installation Guide
http://tinyurl.com/y7zv4kfk
INSTALLATION GUIDE
VONN LIGHTING MODEL#
VAC3315
VAC3315 5-Light Integrated LED Black Chandelier Lighting Fixture
TOOLS YOU MAY NEED
PARTS LIST
A. Mounting Bracket x 1
B. Rubber Plug x 4 + 1
C. Tapping Screw x 4 + 1
D. Outlet Screw x 2 + 1
E. Wire Connector x 2 + 1
F. Ground Screw x 1
G. Canopy Cover Screw x 4
H. Glass Shade x 5
I. Fixed Ring x 5
J. Acrylic Cover x 5
K. Fixed Part x 5
CIRCUIT BOX
LED INFO & WARNINGS
Please read and understand the entire manual before attempting to assemble,
operate, or install the product.
All parts must be used as indicated in these instructions. Do not substitute
any parts, leave parts out, or use any parts that are worn or broken.
Please handle the LED light with care when unpacking. Do not apply pressure to
the LED’s, do not open any factory sealed compartments, and do not touch the
LEDs with your hands.
VONN recommends to install the fixture on its own independent circuit. Do not
install the fixture on the same circuit with the other appliances, or HVAC
systems.
DO NOT CUT WIRES attached to the fixture under any circumstance. Cutting
wires will VOID your warranty. Excess cable should be neatly looped and tucked
into the canopy.
Place the wall switch in the “OFF” position of the room you are installing the
fixture.
Make sure that you have all necessary parts by checking the parts list. If any
part is missing or damaged please contact VONN LIGHITNG CUSTOMER SERVICE at
888-604-8666 for a replacement.
Inspect the LED fixture prior to installation to make sure that it has not been
damaged during shipping.
VONN highly recommends to use a qualified, licensed electrician to install the
fixture.
Do not remove or replace VONN manufactured parts that is provided with the
fixture.
VONN recommends ELV (Electric Low Voltage) type dimmers for this fixture.
Shut “OFF” the electricity at main fuse box.
Fixture Diagram
Instructions
Step 1. Adjust Height
The length of the cable is adjustable. To determine the proper length of the
fixture, hold the fixture canopy up against the outlet box in the ceiling to
adjust the cable.
Depress locking pin on the canopy, hold pin in place, and pull down or push up
on the cable. Repeat step for each cable.
Installer Tip (1): It is recommended that two installers are required to
adjust the height of the fixture. One installer to hold the fixture, and the
second installer to adjust the cables.
Step 2. Install Mounting Bracket Secure mounting bracket (A)with outlet
screws (D), (B), (C).
Step 3. Connect Wires
Supply Wires:
Connect Black (Line Wire) from fixture to Black (Hot Wire) from outlet box.
Connect White (Neutral Wire) from fixture to White (Neutral Wire) from outlet
box.
Ground Wires:
Connect Bare Copper (Ground Wire) from fixture to Green or Bare Copper (Ground
Wire) from outlet box.
Twist wires together clockwise and secure with wire connector (E).
Installer Tip (2): If ground wire is not available in outlet box, then
secure Bare Copper (Ground Wire) from fixture to ground screw (F) on mounting
bracket (A).
Installer Tip (3): It is recommended that two installers are required to
install the fixture. One installer to hold the fixture, and the second installer
to connect the wires.
Step 4. Mount Fixture
Secure canopy to mounting bracket (A) with canopy screws (G).
Tip: Please remove the Glass Shade and Acrylic Cover when checking the
electric connection.
Step 5. Turn Power ON
Turn electricity “ON” at main fuse box.
Place the recommended ELV type dimmer switch in the “ON” position to test the
fixture.
Circuit Box
www.vonn.com
© VONN Lighting, 2022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>