VONN VCP2101 5 Inch 1-Light Integrated LED Pendant Lighting Fixture Installation Guide
- June 3, 2024
- VONN
Table of Contents
VONN VCP2101 5 Inch 1-Light Integrated LED Pendant Lighting Fixture
TOOLS YOU MAY NEED
PARTS LIST
- A. Mounting Bracket x 1
- B. Outlet Screw x 2 + 1
- C. Wire Connector x 2 + 1
- D. Ground Screw x 1
- E. Canopy Cover Screw x 2
CIRCUIT BOX
LED INFO & WARNINGS
- Please read and understand the entire manual before attempting to assemble, operate, or install the product.
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn or broken.
- Please handle the LED light with care when unpacking. Do not apply pressure to the LEDs, do not open any factory-sealed compartments, and do not touch the LEDs with your hands.
- VONN recommends installing the fixture on its own independent circuit. Do not install the fixture on the same circuit with the other appliances, or HVAC systems.
- DO NOT CUT WIRES attached to the fixture under any circumstance. Cutting wires will VOID your warranty. Excess cables should be neatly looped and tucked into the canopy.
- Place the wall switch in the “OFF” position of the room you are installing the fixture.
- Make sure that you have all the necessary parts by checking the parts list. If any part is missing or damaged please contact VONN LIGHTING CUSTOMER SERVICE at 888-604-8666 for a replacement.
- Inspect the LED fixture prior to installation to make sure that it has not been damaged during shipping.
- VONN highly recommends to use a qualified, licensed electrician to install the fixture.
- Do not remove or replace VONN manufactured parts that is provided with the fixture.
- VONN recommends ELV (Electric Low Voltage) type dimmers for this fixture.
- Shut “OFF” the electricity at main fuse box.
Fixture Diagram
Instructions
Step 1. Adjust Height
- The length of the cable is adjustable. To determine the proper length of the fixture, hold the fixture canopy up against the outlet box in the ceiling to adjust the cable.
- Depress the locking pin on the canopy, hold the pin in place, and pull down or push up on the cable. Repeat the step for each cable.
- Installer Tip (1): It is recommended that two installers are required to adjust the height of the fixture. One installer holds the fixture, and the second installer adjusts the cables.
Step 2. Install Mounting Bracket
- Secure mounting bracket
- (A) with outlet screws (B).
Step 3. Connect Wires
- Supply Wires: Connect Black (Line Wire) from the fixture to Black (Hot Wire) from the outlet box.
- Ground Wires: Connect White (Neutral Wire) from the fixture to White (Neutral Wire) from the outlet box.
- Connect Bare Copper (Ground Wire) from the fixture to Green or Bare Copper (Ground Wire) from the outlet box.
- Twist wires together clockwise and secure with wire connector (C).
- Installer Tip (2): If the ground wire is not available in the outlet box, then secure Bare Copper (Ground Wire) from the fixture to the ground screw (D) on the mounting bracket (A).
- Installer Tip (3): It is recommended that two installers are required to install the fixture. One installer to hold the fixture, and the second installer to connect the wires.
Step 4. Mount Fixture
- Secure the canopy to the mounting bracket (A) with canopy screws (E).
Step 5. Turn Power ON
- Turn the electricity “ON” at the main fuse box.
- Place the recommended ELV-type dimmer switch in the “ON” position to test the fixture.
Circuit Box
- www.vonn.com
- © VONN Lighting, 2022
Documents / Resources
| VONN
VCP2101 5 Inch 1-Light Integrated LED Pendant Lighting
Fixture
[pdf] Installation Guide
VCP2101 5 Inch 1-Light Integrated LED Pendant Lighting Fixture, VCP2101, 5
Inch 1-Light Integrated LED Pendant Lighting Fixture, Integrated LED Pendant
Lighting Fixture, LED Pendant Lighting Fixture, Pendant Lighting Fixture,
Lighting Fixture, Fixture
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>