iSMACONTROLLI SFAR-1M-2DI1AO 2 Digital Inputs and 1 Analog Output Modbus I-O Module Instruction Manual

: June 3, 2024
: iSMACONTROLLI

Table of Contents

iSMACONTROLLI SFAR-1M-2DI1AO 2 Digital Inputs and 1 Analog Output Modbus
TOP PANEL
CONNECTION OF OUTPUTS
CONNECTION OF INPUTS
WARNING
TERMINALS OF THE DEVICE
Register access
INSTALLATION GUIDELINE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

iSMACONTROLLI SFAR-1M-2DI1AO 2 Digital Inputs and 1 Analog Output Modbus

I-O Module

SPECIFICATION

Power supply| Voltage| 10-38 V DC; 10-28 V AC
Power consumption| 2 W @ 24 V DC; 4 V A @ 24 V AC

Analog outputs

| 1x Voltage output| 0 V÷10 V (resolution 1,5 mV)
1x Current output| 0 mA÷20 mA (resolution 5 uA)
4 mA÷20 mA (resolution 16 uA)
Digital inputs| 2x, logical “0”: 0-3 V, logical “1”: 6-38 V
Counters| 2x, Resolution 32-bits Frequency max 1 kHz
Baudrate| From 2400 to 115200 bps
Ingress protection| IP40 – for indoor installation
Temperature| Operating -10°C – +50°C; Storage – 40°C – +85°C
Relative humidity| 5 to 95% RH (without condensation)
Connectors| Max 2.5 mm2
Dimension| 90 mm x 56,4 mm x 17,5 mm
Mounting| DIN rail mounting (DIN EN 50022)
Housing material| Plastic, self-extinguishing PC/ABS

TOP PANEL

iSMACONTROLLI-SFAR-1M-2DI1AO-2-Digital-Inputs-and-1-Analog-Output-Modbus-I-O
-Module-fig-1

CONNECTION OF OUTPUTS

Voltage output

iSMACONTROLLI-SFAR-1M-2DI1AO-2-Digital-Inputs-and-1-Analog-Output-Modbus-I-O
-Module-fig-2

Current output

iSMACONTROLLI-SFAR-1M-2DI1AO-2-Digital-Inputs-and-1-Analog-Output-Modbus-I-O
-Module-fig-3

CONNECTION OF INPUTS

Digital inputs

iSMACONTROLLI-SFAR-1M-2DI1AO-2-Digital-Inputs-and-1-Analog-Output-Modbus-I-O
-Module-fig-4

WARNING

Note, an incorrect wiring of this product can damage it and lead to other hazards. Make sure the product has been correctly wired before turning the power ON.
Before wiring, or removing/mounting the product, be sure to turn the power OFF. Failure to do so might cause electric shock.
Do not touch electrically charged parts such as the power terminals. Doing so might cause electric shock.
Do not disassemble the product. Doing so might cause electric shock or faulty operation.
Use the product within the operating ranges recommended in the specification (temperature, humidity, voltage, shock, mounting direction, atmosphere etc.). Failure to do so might cause fire or faulty operation.
Firmly tighten the wires to the terminal. Insufficient tightening of the wires to the terminal might cause fire.

TERMINALS OF THE DEVICE

Register access

Modbus	Dec	Hex	Register Name	Access	Description
30001	0	0x00	Version/Type	Read	Version and Type of the device
30002	1	0x01	Address	Read	Module Address
40003	2	0x02	Baud rate	Read & Write	RS485 baud rate
40004	3	0x03	Stop Bits & Data Bits	Read & Write	No of Stop bits & Data

No of received packets

40034| 33| 0x21| Received packets MSR (Most Significant Reg.)| Read & Write
40035| 34| 0x22| Incorrect packets LSR| Read & Write| No of received packets with error
40036| 35| 0x23| Incorrect packets MSR| Read & Write
40037| 36| 0x24| Sent packets LSR| Read & Write| No of sent packets
40038| 37| 0x25| Sent packets MSR| Read & Write
30051| 50| 0x32| Inputs| Read| Inputs state
40052| 51| 0x33| Outputs| Read & Write| Output state
40053| 52| 0x34| Counter 1 LSR| Read & Write| 32-bit counter 1
40054| 53| 0x35| Counter 1 MSR| Read & Write
40055| 54| 0x36| Counter 2 LSR| Read & Write| 32-bit counter 2
40056| 55| 0x37| Counter 2 MSR| Read & Write
40061| 60| 0x3C| CCounter 1 LSR| Read & Write| 32-bit value of captured counter 1
40062| 61| 0x3D| CCounter 1 MSR| Read & Write
40063| 62| 0x3E| CCounter 2 LSR| Read & Write| 32-bit value of captured counter 2
40064| 63| 0x3F| CCounter 2 MSR| Read & Write

40069

| ****

68

| ****

0x44

| ****

Counter Config 1

| ****

Read & Write

| Counter Configuration

+1 – time measurement (if 0 counting impulses)

+2 – autocatch counter every 1 sec

+4 – catch value when input low

+8 – reset counter after catch

+16 – reset counter if input low

+32 – encoder

40070

| ****

69

| ****

0x45

| ****

Counter Config 2

| ****

Read & Write

40073| 72| 0x48| Catch| Read & Write| Catch counter
40074| 73| 0x49| Status| Read & Write| Captured counter

INSTALLATION GUIDELINE

Please read the instruction before use or operating the device. In case of any questions after reading this document, please contact the iSMA CONTROLLI Support Team (support@ismacontrolli.com).

Before wiring or removing/mounting the product, make sure to turn the power off. Failure to do so might cause an electric shock.
Improper wiring of the product can damage it and lead to other hazards. Make sure that the product has been correctly wired before turning the power on.
Do not touch electrically charged parts such as power terminals. Doing so might cause an electric shock.
Do not disassemble the product. Doing so might cause an electric shock or faulty operation.
Use the product only within the operating ranges recommended in the specification (temperature, humidity, voltage, shock, mounting direction, atmosphere, etc.). Failure to do so might cause a fire or faulty operation.
Firmly tighten the wires to the terminal. Failure to do so might cause a fire.
Avoid installing the product in close proximity to high-power electrical devices and cables, inductive loads, and switching devices. Proximity of such objects may cause an uncontrolled interference, resulting in an instable operation of the product.
Proper arrangement of the power and signal cabling affects the operation of the entire control system. Avoid laying the power and signal wiring in parallel cable trays. It can cause interferences in monitored and control signals.
It is recommended to power controllers/modules with AC/DC power suppliers. They provide better and more stable insulation for devices compared to AC/AC transformer systems, which transmit disturbances and transient phenomena like surges and bursts to devices. They also isolate products from inductive phenomena from other transformers and loads.
Power supply systems for the product should be protected by external devices limiting overvoltage and effects of lightning discharges.
Avoid powering the product and its controlled/monitored devices, especially high power and inductive loads, from a single power source. Powering devices from a single power source causes a risk of introducing disturbances from the loads to the control devices.
If an AC/AC transformer is used to supply control devices, it is strongly recommended to use a maximum 100 VA Class 2 transformer to avoid unwanted inductive effects, which are dangerous for devices.
Long monitoring and control lines may cause loops in connection with the shared power supply, causing disturbances in the operation of devices, including external communication. It is recommended to use galvanic separators.
To protect signal and communication lines against external electromagnetic interferences, use properly grounded shielded cables and ferrite beads.
Switching the digital output relays of large (exceeding specification) inductive loads can cause interference pulses to the electronics installed inside the product. Therefore, it is recommended to use external relays/contactors, etc. to switch such loads. The use of controllers with triac outputs also limits similar overvoltage phenomena.
Many cases of disturbances and overvoltage in control systems are generated by switched, inductive loads supplied by alternating mains voltage (AC 120/230 V). If they do not have appropriate built-in noise reduction circuits, it is recommended to use external circuits such as snubbers, varistors, or protection diodes to limit these effects.