Mimaki JV330 Series Inkjet Printer Instructions

Mimaki JV330 Series Inkjet Printer

Introduction

Thank you for purchasing the Inkjet printer 330 series. Read the safety precautions (“this document” hereinafter) thoroughly and make sure you understand its contents to ensure safe and correct use of the product. Please note that the illustrations contained in this manual are intended to show functions, procedures, or operations and may sometimes differ slightly from the actual machine. The unauthorized reproduction of any portion of this document is strictly prohibited. © 2022 MIMAKI ENGINEERING Co., Ltd.

DISCLAIMERS

• MIMAKI ENGINEERING ACCEPTS NO LIABILITY FOR DAMAGES ARISING DIRECTLY OR INDIRECTLY FROM THE USE OF THE 330 series (“THIS MACHINE” HEREINAFTER), WHETHER OR NOT THE PRODUCT IS FAULTY. MIMAKI ENGINEERING REJECTS ALL LIABILITY FOR DAMAGES, DIRECT OR INDIRECT, RESULTING FROM THE USE OF THIS MACHINE.
• MIMAKI ENGINEERING REJECTS ALL LIABILITY FOR DAMAGES, DIRECT OR INDIRECT, ATTRIBUTABLE TO MATERIALS CREATED WHILE USING THIS MACHINE.
• USING THIS MACHINE IN CONJUNCTION WITH DEVICES OTHER THAN THOSE RECOMMENDED BY MIMAKI ENGINEERING MAY RESULT IN FIRE OR ACCIDENTS. SUCH INCIDENTS ARE NOT COVERED BY THE PRODUCT WARRANTY. MIMAKI ENGINEERING REJECTS ALL LIABILITY FOR DAMAGES, DIRECT OR INDIRECT, ARISING FROM SUCH INCIDENTS.
• USE ONLY GENUINE MIMAKI ENGINEERING INK AND MAINTENANCE LIQUID. USE OF OTHER PRODUCTS MAY RESULT IN FAILURES OR REDUCE PRINT QUALITY. SUCH INCIDENTS ARE NOT COVERED BY THE PRODUCT WARRANTY. MIMAKI ENGINEERING REJECTS ALL LIABILITY FOR DAMAGES, DIRECT OR INDIRECT, ARISING FROM SUCH INCIDENTS.
• DO NOT ATTEMPT TO REFILL THE INK PACKS WITH UNAUTHORIZED INK. SUCH INCIDENTS ARE NOT COVERED BY THE PRODUCT WARRANTY. MIMAKI ENGINEERING REJECTS ALL LIABILITY FOR DAMAGES, DIRECT OR INDIRECT, ARISING FROM SUCH INCIDENTS.

TV and radio interference

• This product emits high-frequency electromagnetic radiation while operating. Under certain circumstances, this may result in TV or radio interference. We make no guarantee that this machine will not affect special radio or TV equipment.If radio or TV interference occurs, check the radio or TV reception after turning off this machine. If the interference disappears when the power is turned off, this machine is likely to be the cause of the interference. Try any of the following solutions or combinations of these solutions:
  • Change the orientation of the TV or radio antenna to find a position where interference does not occur.
  • Move the TV or radio away from this machine.
  • Plug the TV or radio into a power outlet on a power circuit other than the power circuit to which this machine is connected.

FCC (Federal Communications Commission) regulations

This product has been tested and certified to comply with restrictions applying to Class A digital devices under Part 15 of the FCC regulations. These restrictions are designed to provide suitable protection from harmful interference when the printer is used in commercial environments. This product may generate, use, or emit radio frequency energy and may cause harmful interference with radio communications if not installed or used in accordance with the operating manual. Use of this product in residential areas may cause harmful interference. If so, the user is responsible for rectifying such interference.

• Use only the cables recommended by Mimaki Engineering when connecting to this product. Use of other cables may cause the product to exceed the restrictions stipulated by FCC regulations. To maintain compliance with FCC regulations, use the cables recommended by Mimaki Engineering.

To ensure safe use

Symbols

In this manual, the symbols indicate and explain precautions. Make sure you fully understand the meaning of each symbol and use the machine safely and correctly.

Explanation

| Warning| Indicates a potential hazard that may result in death or serious injury if handled improperly or if instructions are disregarded.
| Caution| Indicates a potential hazard that may result in minor or moderate injury if handled improperly or if instructions are disregarded.
| Notice| Indicates a potential hazard that may result in property damage if handled improperly or if instructions are disregarded.
| Warning sign| Indicates something that requires attention. Warning specifics are drawn inside the symbol.
| Mandatory action sign| Indicates an action that must be carried out. The specifics of the mandatory action are drawn inside the symbol.
| Prohibition sign| Indicates a prohibited action. The specifics of the prohibited action are drawn inside the symbol.
Important        Indicates important information related to use of this machine.
| Tip| Indicates useful reference information.
| Reference information| Indicates the corresponding page for related information.

Usage Precautions

In the event of abnormal conditions

• In the event of abnormal conditions such as smoke or unusual odor, turn off the main power immediately and unplug the power cable. Continuing to use the product under these conditions may result in failure, electric shock, or fire. Once you have confirmed that smoke is no longer being emitted, contact your local dealer or our service office. Never attempt to repair the product yourself. Doing so is hazardous.
• Immediately wipe off any ink, maintenance liquid, waste ink, or other liquid used with the product that comes into contact with your skin. Then wash using soap, and rinse with plenty of water. Failure to wash off ink may result in skin inflammation. If your skin becomes irritated or painful, seek medical attention immediately.
• If ink, maintenance liquid, waste ink, or any other liquid used in the product comes into contact with your eyes, rinse immediately with plenty of clean water. Rinse for at least 15 minutes. If you wear contact lenses and they can be easily removed, remove after rinsing for at least 15 minutes with clean water. Be sure to also rinse the undersides of your eyelids. Failure to rinse off ink may result in blindness or impaired vision. If your eyes become irritated or painful, seek medical attention immediately.
• If ink, maintenance liquid, waste ink, or any other liquid used in the product enters your mouth or is swallowed, gargle with water immediately. Do not induce vomiting. Seek medical attention promptly. Inducing vomiting may cause liquid to enter the airway.
• If a large amount of vapor is inhaled, move to a well-ventilated area, keep warm, and rest in a posture that allows easy breathing. If the condition does not improve, seek medical attention promptly.
• If an ink leak occurs, turn off the main power immediately and unplug the power cable. Then, contact your local dealer or our service office.

Power supply precautions

• Use the power cable provided. Otherwise there is a risk of failure, electric shock, or fire. Do not use the power cable with other electronic devices.
• Always grasp the plug when unplugging the power cable. Pulling on the power cable itself may damage the cable and result in failure, electric shock, or fire.
• Do not use the power plug with dust on it. Otherwise there is a risk of failure, electric shock, or fire.
• Avoid touching the blade of the power plug with a metal object. Otherwise there is a risk of failure, electric shock, or fire.
• Do not attempt to modify the cable. Avoid damaging the cable. Avoid placing heavy objects on the power cable or pulling on or exposing the cable to heat. Doing so may damage the cable, resulting in electric shock or fire.
• Do not use extension cords or multi-outlet extension cords. Otherwise there is a risk of failure, electric shock, or fire.
• Do not use if the power cable appears to be damaged or the core wire has an exposed or broken core. Otherwise there is a risk of failure, electric shock, or fire.
• Do not handle the power plug with wet hands. There is a risk of electric shock.
• Plug the power cable plug into a grounded power outlet. Otherwise there is a risk of failure, electric shock, or fire.
• When installing electrical outlets, perform grounding work to prevent electric shock. All electrical work (Class C grounding work; formerly Type 3 grounding work) must be handled by a licensed electrician.
• Do not turn off the main power supply. Turning off the main power supply will disable the automatic maintenance function (including nozzle clogging prevention function and ink discharge channel cleaning function). This will increase the risk of print defects (e.g., nozzle clogging, deflection).
• Use this machine with a power supply that meets specifications.
• Be sure to plug the power cable into a power outlet close to the machine. Insert the power plug blade securely.
• When connecting the power cable, check the input voltage of the power outlet and the capacity of the breaker. Also, connect each cable to a separate power source with an independent breaker. Connecting to power outlets linked with the same breaker will cause the breaker to trip.

Caution regarding moving parts

• Keep parts of the body such as the face and hands away from moving parts. Also keep clothing (e.g., loose clothing and accessories) that may impede work away from the machine. Failure to do so may result in injury.
• Long hair should be tied back. Failure to do so may result in injury.

Do not disassemble or repair

• Do not attempt to disassemble or repair this machine. Otherwise there is a risk of failure, electric shock, or fire.

Handling the cutter

• Avoid touching the cutter blade. Failure to do so may result in injury.
• Do not shake or swing the cutter holder. Doing so may cause the blade to come off.

Heater

• Condensation may form on the print head nozzle surface depending on the ambient temperature and humidity. The formation of condensation may cause printing defects (e.g., nozzle clogging or deflection). Perform head cleaning if any printing defects (e.g., nozzle clogging or deflection) occur during printing. Head Cleaning Set the platen heater to a temperature not exceeding 35 °C, and ensure that the ambient temperature is within the permissible operating temperature range (20 to 30 °C). Precautions”(P. 12)

Other usage precautions

• Keep children away from this machine.
• Do not pull the media when the clamp lever is lowered (the media is clamped). Doing so may damage the machine.
• The underside of the media may be soiled depending on how the printed media has been stored (due to weight when laying printed media rolls horizontally, for example) and the media type. Perform a test beforehand to check that the media does not transfer ink to the underside of the adjacent media.

Disposing of the product

• Please contact your local retailer or service agent.
• When disposing of the product yourself, contact an industrial waste disposal operator or dispose of the product in accordance with local laws and regulations.

Ink or any Other Liquid Used with the Machine

Precautions regarding ink, maintenance liquid, or other liquids used with this machine are included with the containers. Thoroughly read them and make sure you understand the contents.

• Take steps to prevent leakage into natural water systems or domestic wastewater. Some constituents are toxic to aquatic life.
• Be sure to read the safety data sheet (SDS) before use. https://mimaki.com/supply/sds/
• Pay close attention to ventilation and be sure to wear safety glasses, gloves, and a mask when handling ink, maintenance liquid, waste ink, or other solutions used with this machine. Leaking ink may adhere to the skin or get into the eyes or mouth.
• Do not subject cases containing ink to strong shock or violent shaking. Do not attempt to refill the ink. Leaking ink may adhere to the skin or get into your eyes or mouth.
• Do not disassemble cases containing ink. Leaking ink may adhere to the skin or get into your eyes or mouth.
• Avoid storing this product in locations accessible to children.
• When disposing of the product, contact an industrial waste disposal operator or dispose of the product in accordance with the local laws and regulations.
• Do not use ink, maintenance liquid, or other liquids used with this machine with other printers. Doing so may damage the machine.
• Do not touch the metal parts of the ink IC chip. Static electricity may damage the ink IC chip, and dirt or damage may make the ink IC chip unreadable.
• Store in a low place no higher than 1 m above the floor. Dropping this machine may result in splashing ink.
• Store in sealed containers.
• Store in a cool and dark place.
  1. Store ink in an environment where it will not freeze. Note that using thawed ink may affect printing quality due to ink degradation.
  2. When moving ink from cold to warm locations, allow to stand for at least three hours before use in the same conditions as the machine.
  3. Open the ink before use and use up as quickly as possible. Print quality may degrade if the bottles are left open for extended periods.
• Printing is disabled if a different ink IC chip is used.
• Do not store ink, maintenance liquid, or other liquids used with the machine in locations exposed to direct sunlight.
• Do not store ink, maintenance liquid, or other liquids used with the machine in environments where cutting fluid or other volatile substances (such as amines or modified amine alcohol) are present in significant quantities. Storage in such places increases the risk of failure or printing defects (e.g., nozzle clogging, deflection).

Restrictions concerning the product

The ink expiration date is indicated on the Ink pack. Expired ink may cause printing defects or alter the color tone. Printing is possible even if the ink has passed its expiration date. Nevertheless, we recommend replacing with new ink or using up as quickly as possible. Example: When the expiration date is April 2023

• May: Replace with new ink or use up as quickly as possible. Printing is possible.
• June: Replace with new ink or use up as quickly as possible. Printing is possible.
• July: Printing is not possible.
• The message appears on the display.

Installation Precautions

• Do not install this machine in environments where flammable substances are present (e.g., gasoline, flammable spray, alcohol, thinner, lacquer, or powder). This machine is not explosion-proof. The product poses a risk of explosion.
• Do not install this machine in locations where open flames are present. The ink may ignite.
• Do not place vases, pot plants, cups, cosmetics, containers of chemicals or water, or small metal objects on top of this machine. There is a risk of failure, electric shock, or fire if liquids or items drop inside the machine.
• Do not install this machine in humid locations or locations where it may be exposed to splashing water. Otherwise there is a risk of failure, electric shock, or fire.
• Avoid installing this machine in locations accessible to children.
• A ventilation system must be provided if this machine is installed in a poorly ventilated area or sealed room.
• Be sure to observe the following points when installing an extractor outlet:
  1. The extractor outlet must be installed in accordance with applicable local EHS (environmental, health, and safety) guidelines.
  2. If the extractor outlet is fitted with a shutoff valve, the valve must be open when this machine is in use.
• Do not install this machine in locations where dust or powder is present. Failure or printing defects may result (e.g., nozzle clogging, deflection) if dust gets inside this machine.
• Do not install this machine in locations exposed to drafts (e.g., from air conditioning). Disregarding this precaution may result in dust or powder getting inside this machine.
• Do not install this machine in unstable locations or locations subject to vibration. This will increase the risk of failure or printing defects (e.g., nozzle clogging, deflection).
• Do not install this machine in locations exposed to direct sunlight.
• Do not install this machine in locations subject to sudden temperature changes. This will increase the risk of failure or printing defects (e.g., nozzle clogging, deflection).
• Do not install this machine in locations exposed to excessive noise from large machinery.
• Do not install this machine in locations where photographic fixing agents generate vapor or acid gas (e.g., acetic acid, hydrochloric acid) or locations filled with metal working fluids or highly volatile substances (e.g., amines, amine-modified alcohols). Malfunctions or printing defects may result (e.g., nozzle clogging, deflection) as print head ink is more likely to harden under such environments.
• Operating conditions: 20 °C to 30 °C (68 °F to 86 °F), 35 %RH to 65 %RH (no condensation)
• Guaranteed accuracy temperature range: 20 °C to 25 °C (68 °F to 77 °F)

Installation Space

Provide the following space around the machine to allow safe and proper replacement of ink and media:

Item| JV330- 130| CJV330- 130| JV330- 160| CJV330- 160| TS330-1600
---|---|---|---|---|---
Width1| At least 3,920 mm (2,920 mm)| At least 4,170 mm (3,170 mm)
Depth1| At least 4,050 mm (2,050 mm2)| At least 2,820 mm (820 mm)
Height 1| (1,305 mm)
Weight| 358 kg| 363 kg| 368 kg| 373 kg| 240 kg

1. The figures in parentheses indicate machine dimensions.
2. Including the media chute

When Relocating This Machine

Contact your local dealer or our service office. Attempting to handle relocation yourself may result in failure or damage.

Safety Interlocks

This machine is equipped with interlocks to ensure safety during use. Printing will abort if you open the covers while printing is underway. If so, you will need to resend the RIP data.

• Safety interlock locations

Warning Label

Make sure you fully understand the details indicated on the various warning labels. If any of the warning labels becomes dirty and illegible or peel off, contact your local dealer or our service office to request new warning labels .

become trapped.
2| M907833| | Indicates dangerous moving parts.
3| M903239| | Indicates hot parts.

•   JV/CJV: Pre-heater, post-heater

•   TS: Post-heater

4| M903330| | Wear safety glasses and gloves while working.
5| M906144| | Indicates hot parts.

•   JV/CJV only

6| M903405| | Beware of the cutter.

•   JV: Carriage, XY carriage

•   CJV: Carriage, cutter unit, XY carriage

•   TS: Carriage

7| M905811| | Indicates dangerous moving parts.
8| M906031| | Describes the power cable.
9| M907935| | Indicates dangerous live parts.
10| M917747| | Beware of the cutter.

•   JV/CJV only

11| M917991| | Indicates illuminating LED hot parts.
No.| Order code| Label| Details
---|---|---|---
12| M905935| | Avoid touching the pinch roller lever.

•   CJV only

Appendix

This chapter lists the specifications and functions of this machine.

Relay Box

• A fire may occur if another manufacturer’s external drying heater is used. Be sure to connect to the machine using either the compact relay box or relay box 2 specified as options.
• The 330 series allows only one relay box (OPT-J0370 or OPT-J0407) to be connected.
• The optional connection relay cable (OPT-J0512 drying fan connection kit) is required when using a relay box.

Overview

The relay box switches the heater’s power on and off automatically in conjunction with the machine operations.

• The heater is turned off when printing stops to prevent heating while the machine is not moving.
• The relay box cannot function to control the temperature of an external drying heater. The temperature should be set on the external heater itself.

Specifications

Small relay box (OPT-J0370)

| Power supply specificatio ns| Single-phase 100 V to 120 V AC, 12 A, single- phase 200 V to 240 V AC, 8 A, 50/60 Hz, single-circuit main power supply
---|---|---
Type| Resistance heater or electric heater using lamp
Relay box 2 (OPT-J0407)

| Power supply specificatio ns| Single-phase 100 V to 240 V AC, 30 A, 50/60 Hz, single-circuit main power supply
Type| Resistance heater or electric heater using lamp

References

• Mimaki Global
• SDS (USA) | MIMAKI

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>