CANNON Pedestal Mounts Owner’s Manual
- June 3, 2024
- CANNON
Table of Contents
CANNON Pedestal Mounts
Pedestal Mount Models & Features
1904030 Fixed Base Downrigger Pedestal 4”
1904031 Fixed Base Downrigger Pedestal 6”
Cannon’s fixed base downrigger pedestals can be surface mounted or track
mounted for a variety of mounting
positions and easy removal. The 3/4” thick aluminum top plate is pre-drilled
and tapped for mounting Cannon down-riggers as well as most Scotty®, Big Jon®,
Penn®, Vector, Proos, Fishlander and Walker downriggers. Components are made
from clear anodized aluminum and stainless steel for strength and corrosion
resistance. The fixed base
downrigger pedestals are compatible with Cannon, Bert’s, and Traxstech track
systems. Available in 4” and 6” heights.
1904032 Swivel Base Downrigger Pedestal 4”
1904033 Swivel Base Downrigger Pedestal 6”
Cannon’s swivel base downrigger pedestals can be surface mounted or track- mounted for a variety of mounting positions and easy removal. With 16 locking points, these downrigger pedestals allow for 360° downrigger rotation with locking points every 22.5°. The 3/4” thick aluminum top plate is pre-drilled and tapped for mounting Cannon downriggers as well as most Scotty®, Big Jon®, Penn®, Vector, Proos, Fishlander, and Walker downriggers. The bearing system ensures smooth swivel action even while a downrigger weight is attached. Components are made from clear anodized aluminum and stainless steel for strength and corrosion resistance. The swivel base downrigger pedestals are compatible with Cannon, Bert’s, and Traxstech track systems. Available in 4” and 6” heights.
How to use the Swivel Pedestal
Cannon’s swivel base downrigger pedestals allow you to rotate the mounting
plate for optimal positioning. To rotate the mounting plate, disengage the
lock pin by pulling the lock pin handle down. Turn the plate to the desired
angle and release the spring-loaded lock pin making sure that it reengages.
Check to make sure the swivel is in a
fixed position.
Swivel Base Break Away Reset
The Cannon Swivel bases feature a unique breakaway system which allows the top
plate to rotate while in the locked position. The breakaway feature will help
prevent damage to the downrigger and boat in the event that the downrigger
boom or ball would strike an object. If this should occur, the mounting plate
of the swivel pedestal will turn, giving way to the unexpected load. The
mounting plate can be reset back to any position by following these steps:
- Locate the 3/8” bolts on the bottom of the top plate (See Figure 1).
- With the pedestal locked in any position, loosen the bolts
- Rotate the mounting plate back to the desired position.
- Tighten the 3/8” bolts to 25 ft-lb.
Note: The downrigger weight must be stowed before resetting the swivel pedestal mount.
Mounting the Pedestal to Your Boat
Mounting Directly to the Deck or Gunnel
Carefully choose an ideal position where you may best utilize your pedestal mount. Use the base of the pedestal as a template to mark hole locations and drill four 9/32” diameter through holes. Fix the pedestal to the deck or gunnel using four 1/4”-20 flat head screws with four flat washers, lock washers, and nuts (not included). To deter-mine the length of screw needed, measure the thickness of deck that you are mounting to and add at least 3/4”.
Mounting to Cannon Track Mount
For versatility and lightening quick mounting, the Cannon Mounting Track
system is ideal for utilizing your pedestal mount on your boat. Slide the base
of the pedestal into the track and tighten the thumb screws to fix the
pedestal in
position. You may use a 3/16” Allen wrench for additional tightening.
Note: For the Swivel Pedestal Mount, rotate the release handle to access
the top of the thumb screw with the Allen wrench.
1904025 Aluminum Mounting Track 6”
1904026 Aluminum Mounting Track 12”
1904027 Aluminum Mounting Track 18”
1904028 Aluminum Mounting Track 24”
1904029 Aluminum Mounting Track 36”
Cannon tracks allow for flexible mounting positions and easy removal of
Cannon’s track system accessories. Locking grooves allow thumb screws to index
with the track and prevent accessories from twisting. The system is compatible
with Cannon, Bert’s, and Traxtech track system products. Components are made
from clear anodized aluminum
and stainless steel for strength and corrosion resistance. All mounting
hardware is included. Available in 6, 12, 18, 24, and 36-inch lengths.
Mounting to Cannon Deck Mount
The Cannon Deck Mount works great for adding stability and easy removal of your pedestal mount. With your Cannon Deck Mount installed on your boat, attach your pedestal mount by removing the thumb screws and fastening the pedestal base to the plate with four 1/4”-20 x 3/8” long flat head screws.
1904000 Deck Mount
The Cannon Deck Mount plate is a four-inch by three-inch clear anodized
aluminum plate which allows the hard mounting of Cannon Dual Axis Rod Holders.
The plate comes with a black protective mounting boot and all mounting
hardware.
Mounting Your Downrigger to the Pedestal Mount
The Cannon Pedestal Mount provides 1/4”-20 tapped mounting holes for attaching most downrigger mounting bases. To attach a mounting base you will need four 1/4”-20 screws (not included). To determine the length of screws needed, measure the thickness of the downrigger mounting base and add 1/2”. See below for screw lengths for the Cannon Downrigger mounting bases.
Magnum / Digi-Troll Tall Mounting Base — 2” Long Truss Head screw
Uni-Troll Low-profile Mounting Base — 1” Long Truss Head screw
Easy-Troll / Lake-Troll Tab-Lock Base — 3/4” Long Truss Head screw
Pedestal Mount \ Accessory Compatibility
Troubleshooting – Swivel Pedestal
Problem: Pedestal will not rotate when the lock pin is disengaged.
Make sure the downrigger line is all the way up. Any load on the downrigger or
pedestal may prevent the pin from disengaging. Spray a lubricant into the slot
which the lock pin slides. Make sure the lock pin moves freely up / down.
Problem: Pedestal rotates while in a locked position under normal use.
The breakaway bolts are not tight enough. Re-torque bolts to 25 ft-lb.
NOTE : Bolts may have to be tightened higher than 25 ft. lbs under some
conditions. Do not exceed 35 ft-lb as this may damage the top plate.
Problem: Pedestal did not break away while locked when the boom struck an
object.
The breakaway bolts are over-tightened. Loosen bolts and re-torque to 25 ft.
lbs.
Replacement Parts
Part | Part Number | Description | USED ON |
---|---|---|---|
**** | 3393413 | THUMB SCREW | 1904030, 1904031, 1904032, 1904033 |
CANNON® LIMITED WARRANTY
Johnson Outdoors Inc. warrants to the original purchaser that the accompanying product (see exclusions below) is free from defects in material or workmanship for a period of one (1) year from the date of purchase. Within the warranty period, Johnson Outdoors Inc. will, at its option, either repair or replace the same without charge (but no cash refunds will be made). The unit must be returned, prepaid, and with proof of the date of purchase to the following:
- Johnson Outdoors, Inc Cannon Division, 121 Power Drive, Mankato, MN 56001
This limited warranty may be enforced only by the original purchaser; all
subsequent purchasers acquire the product “as is” without
any benefit of this limited warranty. Repair or replacement of the product as
set forth in this limited warranty shall be the original
purchaser’s sole and exclusive remedy and Johnson Outdoors Inc.’s sole and
exclusive liability for breach of this warranty.
EXCLUSIONS
This warranty does not apply in the following circumstances:
- When the product has been connected, installed, combined, altered, adjusted, serviced, repaired, or handled in a manner other than according to the instructions furnished with the product
- When a serial number has been defaced, altered, or removed
- When any defect, problem, loss, or damage has resulted from any accident, misuse, negligence, carelessness, or abnormal use, or from any failure to provide reasonable and necessary maintenance in accordance with the instructions of the owner’s manual
LIMITATION AND EXCLUSION OF IMPLIED WARRANTIES AND CERTAIN DAMAGES
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THESE LIMITED WARRANTIES. JOHNSON OUTDOORS INC. DISCLAIMS LIABILITY FOR INCIDENTAL AND CONSEQUENTIAL DAMAGES, AND IN NO EVENT SHALL ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, EXTEND BEYOND ONE YEAR FROM THE DATE OF PURCHASE. THIS WRITING CONSTITUTES THE ENTIRE AGREEMENT OF THE PARTIES WITH RESPECT TO THE SUBJECT MATTER HEREOF; NO WAIVER OR AMENDMENT SHALL BE VALID UNLESS IN WRITING SIGNED BY JOHNSON OUTDOORS INC.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
To download product manuals or purchase Cannon products from an authorized dealer, please visit our web page at www.cannondownriggers.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>