GYS 057678 Plastics Welding Kit Instruction Manual
- June 3, 2024
- GYS
Table of Contents
PLASTICS
WELDING KIT
DESCRIPTION OF HOT AIR GUN
- Power cord
- On/Off Switch
- Thermostat
- Ergonomic handle
- Air filter (cleaning brush provided)
- Rubber protection
- Hot air nozzle
- Protection tube
- TIP – Nozzle
- Fixing screw
INSTRUCTIONS OF USE
- Use the adapted nozzle and plug the hot air gun.
- Adjust the temperature using the thermostat, switch on the hot air gun and wait until the gun reaches the desired temperature (+/- 5 min).
- IT IS MANDATORY to let the gun cool down after use (thermostat on position 0).
- After use, let the hot air gun on, on thermostat position 0, to let it cool down before switching OFF. Failure to do so may lead to irreversible damage to the hot air gun.
- Do not touch the hot air nozzle. Regularly clean the air filter using the provided cleaning brush.
AUTOMOTIVE PLASTICS REPAIR
- Fit the TIP20MM nozzle on the hot air gun.
- Let the hot air gun heat up, on thermostat position 8.
- On the front side of the bumper, make a chamfer on the crack and glue an aluminium tape on the back side.
- Heat up the plastics brazing stick before applying it on the bumper.
- Continue heating the brazing stick, while slowly applying it on the bumper.
- Let the repair area cool down, or use a Freezer spray can to cool down faster.
- Grind using an orbital sander (low speed), then apply putty, primer and paint.
- In case of large cracks or holes, apply a stainless steel mesh on the back side.
TECHNICAL DATA
| Power : | 1600 W |
|---|---|
| Voltage : | 230 V ̴ |
| Frequency : | 50/60 Hz |
| Temperature : | 20 – 700 °C |
| Air Flow : | max.230 l/min |
| Weight : | 1.3 kg avec Cordon 3 M |
| Dimensions : | Ø 100 x 300 mm handle Ø 56 mm |
| Conformity : | CE |
OTHER APPLICATIONS :
- Welding and gluing of floor coverings, textiles and technical covers.
- Flat roofs and roofs with steep slope (EPDM, …)
- Thermoforming and retraction.
- Reconstruction of holes, cracks with the use of the plastic brazing sticks (thermostat 8).
- Drying of wet surfaces.
- Defrosting of frozen pipes.
- Removal of paint, varnish and glue…
ASSOCIATED PRODUCTS
| 048898 – set of 12 freezer spray cans –-50°C / 400ml
---|---
| 052956 – set of 10 plastics brazing sticks
| 058231 – pressure wheel for bumper repair
| 052949 – set of 2 stainless steel mesh 25×12.5Cm
SYMBOLS
| – Caution ! Read the user manual.
---|---
| – Use gloves that guarantee electrical and thermal insulation.
| – Use a noise helmet if the sanding reaches a noise level above the
authorized limit (the same applies to anyone in the work area).
| – Mandatory safety glasses.
****| – Devicecompliant with European directives. The certificate of
compliance is available on our website (www.gys-welding.com)
| CMIM : Moroccan Certificatio
| – Equipment in compliance with British requirements. The British Declaration
of Conformity is available on our website (see home page).
| – This hardware is subject to waste collection according to the European
directives 2002/96/UE. Do not throw out in a domestic bin !
| – This product should be recycled appropriately.
JBDC
1, rue de la Croix des Landes
CS 54159
53941 SAINT-BERTHEVIN Cedex
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>