amazonbasics B08J4KFHMN Electronic Keypad Deadbolt Door Lock User Manual

B08J4KFHMN Electronic Keypad Deadbolt Door Lock
Safety and Use Manual ** **

Important Safeguards

Read these instructions carefully and retain them for future use. If this product is passed to a third party, then these instructions must be included.

• Prevent unauthorized entry. The electronic lock is pre-programmed with default user code and programming code. After installation and setup, change the codes.
• Store the codes in a safe place and change them from time to time.
• Make sure that no unauthorized person has the access to the codes.
• Do not use excessive force or sharp objects to push the buttons on the keypad.
• Close the door completely when going outside. The manufacturer does not assume the responsibility for any harm caused by engagement of the lock on an improperly closed door.
• No lock can provide complete security by itself. This product may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. The builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, consult a qualified locksmith or other security professionals.

Before First Use

• Remove all the packing materials.
• Remove and review all components before use.
• Check the product for transport damages.

Installation

For installation steps, refer to the provided installation manual.

Operation

4.1 Inserting batteries
NOTICE

• Always use alkaline batteries. Insert batteries correctly with regard to polarity ( + and – ) marked on the battery and the product.
• Exhausted batteries should be immediately removed from product and properly disposed. Replace all batteries a t the same time. Do not mix new and old batteries.
• Insert the batteries after the product has been installed on the door.
• The programming code and user code will be stored after replacing batteries.

1. Push the battery compartment cover (M) upwards , then pullit out.
2. Insert four AA batteries into the battery compartment.
3. Slide the battery compartment cover (M) back onto the interior assembly (K).

4.2 Indicator signals and lights

• The lock will temporarily freeze for 45 seconds.
  4,3 Programming

NOTICE   Programming and assigning new codes is only possible when the lock is unlocked and the door is open.
NOTICE   inthis chapter, PC refers to programming code; and UC refers to user code.
4.3.1 Determining Door Handing
NOTICE Before use, first retract the bolt, then follow below combination to teach the l o c k the orientation of the door. The default programming code (PC) is 0000.

The latch bolt will extend and retract. Once the operation is successful, the lock beeps twice and the indicator flashes green twice.

NOTICE
4.3.2 Changing Programming Code

• The default programming code (PC) is 0000. Change the code with 4-10 digits in length.
• The programming code and user code cannot be identical.
• The l o c k will temporarily freeze for 45 seconds i f unauthorized codes code has been entered more than 5 times.

4.3.4 Adding New User Code
NOTICE
The default user code (UC) is 1234. Change the code with 4-10 digits in length. Up to 10 sets of user codes can be saved.

• The programming code and user code cannot be identical.
• The l o c k will temporarily freeze for 45 seconds if unauthorized codes code has been entered more than 5 times.

4.3.6 Deleting an Existing User Code

4.3.7 Deleting All User Codes at Once
NOTICE
When all user codes are deleted, the lock can only be operated with the keys. Auto-lock or keypad functions are disabled until a new user code is set.

4.3.8 Activating/Deactivating Auto-Lock
NOTICE
After the auto- lock function is activated , the lock locks automatically after being unlocked for 30 seconds.

4.3.9 Setting Auto-Lock Time Delay
NOTICE
The default auto – lock time delay is set to 30 seconds. Set the time delay between 10 and 99 seconds.

4.3.10 Muting/Unmuting Signal Sounds
NOTICE
When the signal sound is muted, the indicator lights are still active.

4.3.11 Enabling/Disabling All U ser Codes
NOTICE | When all user codes are disabled , the lock can only be operated with the keys. Auto-lock or keypad functions are disabled.

4.3.12 Creating a One-Time User Code
NOTICE
The one-time user code can only be used once and will expire automatically.

4.4 Restoring Default Settings

NOTICE
Usinga pointed object, press and hold the reset button for 5 seconds. The lock emits 3 long beeps and all the settings are restored to the original factory settings. Follow  steps in chapter “Determining Door Handing” before re- programming.

Cleaning and Maintenance

• To clean the product, wipe with a soft, slightly moist cloth.
• Regularly check that all the components and fasteners are tightened.
• Never use corrosive detergents, wire brushes, abrasive scourers, metal or sharp utensils to clean the product.

Troubleshooting

The latch does not retract easily when rotating the turn piece or using the key| Ensure the position of the strike plate on the door frame is aligned with the position of the latch.
The electronic lock  does not function.| Check the connection of the cables. The colored edges of the connectors must be
aligned.
Ensure the batteries are new and installed correctly.
The indicator light flashes red 3 times when determining the door handing.| Ensure the door is open and unlocked.
Use new set of batteries.
Reset the product to default factory settings and determine the door handing again.
Ensure the door is open and unlocked.
Use new set of batteries.
Reset the product to default factory settings and determine the door handing again.| Ensure the electronic lock is programmed with a t  least one user code. See chapter “Adding new user code”.
Ensure the user codes are not disabled. See chapter “Enabling/Disabling all user codes”.
Door jammed while attempting to lock.
Upon pressing any of the keys, all keys light up blue and the lock  does not function.| Manually re-lock door. If needed, reposition the strike plate .
5 incorrect user codes entered within one minute. The lock  is temporarily locked for 45 seconds. Re-enter the user code after 45 seconds.

FCC-Shpplier’s Declaration of Conformary

Unique Identifier
BO8J4KFHMN – Traditional Electronic Keypad Deadbolt Door Lock with Passage Lever
– Satin Nickel
B08J4K74SB – Traditional Electronic Keypad Deadbolt Door Lock with Passage Lever
– Oil Rubbed Bronze
BO8J4K728S – Traditional Electronic Keypad Deadbolt Door Lock with Passage Lever
– Matte Black
BO8J4K9YMxX – Contemporary Electronic Keypad Deadbolt Door Lock with Passage
Lever – Satin Nickel
B08J4J5N4G – Contemporary Electronic Keypad Deadbolt Door Lock with Passage
Lever – Matte Black
BO7J4VHVN5, BO7J4HXTWJ, BO7J4VQCMF, BO7J4HXTWT, BO7J4VLVPF- Electronic
Keypad Deadbolt – Keyed Entry

7.1 FCC Compliance Statement

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
2. this device may not cause harmful interference, and
3. this device must accept any interference received, including interference that may cause undesired operation.
4. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

7.2 FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur ina particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.

Canada iC Notice

• This Class B digital apparatus complies with Canadian CAN ICES-003(B) / NMB-003(B) standard.

Battery Disposal

Do not dispose of used batteries with your household waste. Take them to an appropriate disposal/collection site .
To learn more about recycling batteries, visit: call2recycle.org/what- can-i-recycle

Specifications

Electronic lock

Passage lever (for BO8J4KFHMN, B08J4K74SB, BO8J4K728S, BO8J4K9YMX, BO8J4J5N4G)

Feedback and Help

We would love to hear your feedback. To ensure we are providing the best customer experience possible, please consider writing a customer review.
Scan QR Code below with your phone camera or QR reader:
If you need help with your Amazon Basics product, please use the website or number below.

**** amazon.com/gp/help/customer/_contact- us
= +1.877-485-0385 https://www.amazon.com/review/review-your- purchases/listing/?ref=445439_UM_CR

amazin.com/AmazonBasics
MADE IN CHINA

Documents / Resources

| amazonbasics B08J4KFHMN Electronic Keypad Deadbolt Door Lock [pdf] User Manual
B08J4KFHMN Electronic Keypad Deadbolt Door Lock, B08J4KFHMN, Electronic Keypad Deadbolt Door Lock, Keypad Deadbolt Door Lock, Deadbolt Door Lock, Door Lock
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>