PROSLAT Heavy Duty Hoist Installation Guide
- June 3, 2024
- Proslat
Table of Contents
PROSLAT Heavy Duty Hoist
TOOLS REQUIRED
BOX CONTAINS
WARNING
Please read the installation carefully prior to installation. Before using
the product thoroughly test the fully-weighted product (with equipment in
place) to ensure the product has been installed properly. Do not allow
children to play with products. Proslat is not responsible for any damage
resulting from improper installation, overloading, or product failure.
STEP 1
WARNING
It is important that your hoist is attached to a solid wood ceiling joist. The
joist must be 2” x 4” or larger.
STEP 2
Verify which way your ceiling joists are. Hoist brackets can be mounted
parallel or perpendicular. Use two wood screws each to mount the back pulley
and the front pulley to the ceiling, ensuring the distance between the two
matches the measurement made in step 1. Pre-drilling 1/8” pilot holes in the
ceiling will make mounting the pulleys easier.
STEP 3
Attach pulley brackets to ceiling mounts.
STEP 4
Untangle your rope. Each end of the rope will be tied to a ceiling bracket on
the hoist. The left side will be used for one set of pulleys, the right side
for the other. Start by threading the left side rope through the brake device
as shown in the picture below. The left side rope will go through the first
pulley, then to the second pulley, down around the second hook and up to the
ceiling bracket. 
Once through the hole in the
ceiling mount, tie a figure eight knots right after the hole and then a double
knot around the bolt. Thread the other end of the rope through the right side,
down around the first hook and up to the ceiling bracket. Once through the hole
in the ceiling mount, tie a figure eight knot right after the hole and then a
double knot around the bolt.
STEP 5
Use two wood screws to mount the rope cleat to the wall. When the bike is up
to the ceiling, the excess rope should be stored in the cleat.
OVERHEAD WARNING
Make sure that there are no obstructions to restrict the operation of the bike lift.
USING THE BIKE LIFT
Hook the bike handlebar and seat with the hooks and be sure the ropes are
not twisted (for bulky items, attach nylon straps to hooks). The bike can now
be raised to the ceiling by the pulling rope. The rope will lock in place with
each pull, preventing the bike from falling. For safety, tie the rope on the
cleat and wind the excess rope around it. DO NOT CUT THE ROPE.
LOWERING THE BIKE
Pull the rope down at 90° from the ceiling bracket maintaining tension on
rope. The tension will keep the locking mechanism open and the bike will be
able to lower. Slowly let one rope out at a time as the bike lowers. Once the
bike is low enough, remove it from the hooks and tie the rope back to the
cleat.
KAYAK OR SIMILAR APPLICATION
For use with nylon straps, hang each end of the strap on one of the hooks. You
can adjust the length of the strap at the buckle.
PROSLAT HOIST WARRANTY
We guarantee our hoist against material and workmanship defects for 5 years. This warranty does not include any cost related to the installation or return of the hoist. This warranty is valid provided that the maximum weight supported by the hoist does not exceed 100 pounds. The customer, installer or dealer, releases the SLATE of all claims if the hoist has been loaded with more than mentioned above. The hoist MUST BE installed as described in the
INSTALLATION INSTRUCTIONS
This warranty does not cover corrosion, rust or discoloration of paint, or product failure due to misuse, abuse, faulty installation, alteration or any other failure not related to defects in materials or workmanship.
DISCLAIMER OF LIABILITY
Proslat Inc. and its successors, distributors and dealers (hereafter SELLER)
shall in no way be responsible for the product’s proper use and service. THE
BUYER HEREBY WAIVES ALL LIABILITY CLAIMS. The BUYER acknowledges that he/she
is not relying on the SELLER’s skill or judgment to select or furnish goods
suitable for any particular purpose and that there are no liabilities that
extend beyond the description on the face hereof and the BUYER hereby waives
all remedies or liabilities, expressed or implied, arising by law or
otherwise, (including without any obligations of the SELLER with respect to
merchantability and consequential damages) or whether or not occasioned by the
SELLER’s negligence.
The SELLER disclaims any warranty and expressly disclaims any liability for personal injury or damages. The BUYER acknowledges and agrees that the disclaimer of any liability for personal injury is a material term for this agreement and the BUYER agrees to indemnify the SELLER and to hold the SELLER harmless from any claim related to the item of the equipment purchased. Under no circumstances will the SELLER be liable for any damages or expenses by reason of the use or sale of any such equipment. The SELLER assumes no liability regarding the improper installation or misapplication of its products. It is the installer’s responsibility to check for proper installation and if in doubt, contact the manufacturer.
These assembly guidelines will direct you through the process of assembling a section of Proslat Inc product. Please keep in mind that they may not cover every assembly or installation scenario you may encounter. Since each installation is unique in its performance requirements, the ultimate installation method used is the sole responsibility of the installer. Proslat Inc. disclaims any liability or responsibility for the improper installation of this product. The purchaser is solely responsible for compliance with applicable local codes. Proslat Inc. recommends that all designs be reviewed by a licensed architect, engineer or local building official before installation.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>