Proslat 8 x 4 ft PVC Panel Instructions Manual
- June 2, 2024
- Proslat
Table of Contents
- YOUR BOX CONTANINS
- STEP 1 Watch our installation video
- Step 2
- Step 3
- Step 4
- Step 5
- Step 6
- Step 7
- Step 8
- Step 9
- Step 10
- Installing wider than 8 ft (2.44 m)
- FREQUENTLY ASKED QUESTIONS
- Top panel cut
- IF YOU HAVE ANY QUESTIONs AFTER READING THESE INSTRUCTIONS.
- Proslat PVC panels warranty
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
INSTRUCTIONS
8 x 4 ft Proslat panel section 8PRO001-AUG1815
YOUR BOX CONTANINS
88 x 2 in (5 cm) screws (Dual Robertson & Phillips Pan head #8) Square driver strongly recommended
Tools Required
STEP 1 Watch our installation video
Step 2
Decide at what height and location you would like your Proslat panels section.
You must start & finish on studs. Studs should be centered 16 in (40.6 cm) apart in order to supports 75 lb (34 kg) per square foot.
In order to support 75 lbs (34 kg) per square foot, your studs must be a
maximum of 16 in apart.
Step 3
Once you have choosen your location, verify that you are starting and finishing on a stud and locate and mark all studs between starting and finishing with your stud finder as you will need to screw each panel into each stud.
Step 4
Use snips to cut one of your J trims at 96 in (2.44m) for the bottom horizontal trim.
- If you are installing only one section (4 ft high), go to step 5A.
- If you are installing more than one section high, go to step 5B.
Step 5
5A (One section) – Cut one of your J trims in two pieces of 48 ½ in (1.23 m).
5B (Two sections high) – Cut your second J trim to 96 ½ in (2.45 m). Open your second box and retrieve one of the J trims and cut it to 96 ½ in (2.45 m)
Step 6
For this step, it is best to have two (2) people. Install your bottom horizontal J trim at desired starting height (the wider side installs against the wall), level and screw into the middle 5 studs. Do not screw into the first and last studs.
Step 7
Overlap your vertical trim with your horizontal trim (the wider side installs against the wall) and screw through both. Level vertical trim and install one screw at the top. Repeat on the other side. Your panels will be screwed through the J trims holding both in place.
Step 8
To install the first panel, insert one end of your panel (left or right) into the vertical J trim and slightly curve the panel so it will insert into the other vertical J trim. Make sure your panel is seated into bottom J trim and is level. Screw through the upper cavity of the panel into each stud (16-in apart). Drive screws at either end of the panel through the J trim and into your stud. This will hold your vertical J trims to the wall.
Step 9
Insert the next Proslat panel into one of your vertical J trims, interlocking
the panel with the one below it. Curve your panel and insert into the J trim
on the other side, again interlocking the panel with the one below it. Push
down on the panel to overlap with the panel below it, making sure it is
properly seated and level. Make sure you screw into every stud before
installing the next panel.
Repeat until your section is done, verifying level every 3 panels.
Properly interlocked panels will conceal previous panel’s installation screws.
Properly overlapped
Step 10
Install your top L trims by simply clipping them into the lip above the screw cavity.
Installing wider than 8 ft (2.44 m)
Some kits contain an extra J & L to install in a 2’ x 16’ configuration.
If you are installing two 4 ft (1.2 m) panels side by side, you will need to use two J trims back to back to hide the joint. Or, you can order additional H trims from our website.
FREQUENTLY ASKED QUESTIONS
CONCRETE OR BLOCKWALL INSTALLATION
If your walls are made of concrete or blocks, you will need to fasten 2”x3” studs or furring strips vertically using a cement screw and then install your Proslat to the studs.
24’’ stud center
Our product is designed to hold 75 lbs (34 kg) per square foot when the studs are 16” (40.6 cm) apart. If your studs are wider apart please apply some adhesive to the back of the panel.
Top panel cut
If you have done a complete wall and you have had to cut your top panel to fit,
you will need to use silicone to install your top trim.
IF YOU HAVE ANY QUESTIONs AFTER READING THESE INSTRUCTIONS.
Please call our customer service
1.888.691.2944
Monday to Friday
8:00 am to 5:00 pm EDT
Proslat.com
Proslat PVC panels warranty
This document details the Solutions Murales Proslat Inc Warranty for all new
Proslat Panels purchased anywhere in North America. This Lifetime
Warranty extends only to the first retail purchaser of the wall panel.
Lifetime Warranty. Solutions Murales Proslat Inc (hereafter Proslat) warrants
its wall panels against defects in material or workmanship for a lifetime
period. Proslat will replace any defective panel as long as it was installed
and maintained according to the printed instructions. Any Proslat panel
replaced under the terms of the Lifetime Warranty inherits the remaining
warranty period from the original purchase. Exclusions. The Proslat Warranty
does not cover the following: – Damage that results from improper installation
or
misuse or abuse; – Damage due to acts of God, fire, or accident; – Damage
created by non-Proslat accessories such as hooks, baskets, cabinets and
shelving; – Damage that results from loading accessories beyond the stated
maximum weight capacity; – The cost of labor or accessory materials; and
shipping cost to return defective products. Limitations of Warranty. The above
Lifetime Warranty is the exclusive warranty for Proslat Panels. Proslat
disclaims all other warranties, express or implied, including any implied
warranties or merchantability, fitness for particular purpose or otherwise. If
you live in an area where consumer law prohibits this disclaimer, the above
Lifetime Warranty will not extend the time period of any such implied
warranty.
Obtaining Lifetime Warranty Service. For warranty service, call
1.888.691.2944. You will need your original proof of purchase and photos to
illustrate the claimed defect.
DISCLAIMER OF LIABILITY
Solutions Murales Proslat Inc. and its successors, distributors and dealers
(hereafter SELLER) shall in no way be responsible for the product’s proper use
and service. THE BUYER HEREBY WAIVES ALL LIABILITY CLAIMS. The BUYER
acknowledges that he/she is not relying on the SELLER’s skill or judgment to
select or furnish goods suitable for any particular purpose and that there are
no liabilities which extend beyond the description on the face hereof and the
BUYER hereby waives all remedies or liabilities, expressed or implied, arising
by law or otherwise, (including without any obligations of the SELLER with
respect to merchantability and consequential damages) or whether or not
occasioned by the SELLER’s negligence. The SELLER disclaims any warranty and
expressly disclaims any liability for personal injury or damages. The BUYER
acknowledges and agrees that the disclaimer of any liability for personal
injury is a material term for this agreement and the BUYER agrees to indemnify
the SELLER and to hold the SELLER harmless from any claim related to the item
of the equipment purchased. Under no circumstances will the SELLER be liable
for any damages or expenses by reason of use or sale of any such equipment.
The SELLER assumes no liability regarding the improper installation or
misapplication of its products. It is the installer’s responsibility to check
for proper installation and if in doubt, contact the manufacturer. These
assembly guidelines will direct you through the process of assembling a
section of Solutions Murales Proslat Inc product. Please keep in mind that
they may not cover every assembly or installation scenario you may encounter.
Since each installation is unique in its performance requirements, the
ultimate installation method used is the sole responsibility of the installer.
Proslat Inc. disclaims any liability or responsibility for the improper
installation of this product. The purchaser is solely responsible for
compliance with applicable local codes. Solutions Murales Proslat Inc.
recommends that all designs be reviewed by a licensed architect, engineer or
local building official before installation.
Proslat 8 x 4 ft PVC Panel Instructions Manual – Optimized
PDF
Proslat 8 x 4 ft PVC Panel Instructions Manual – Original
PDF
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>