DEFA 712800 Solid EV Charging Station Installation Guide

June 3, 2024
DEFA

DEEA Solid™
712800 Solid EV Charging Station
Installation Guidehttp://defa.com/power-get-started

Safety information

Important! Read this document before installing the device. Failure to follow any of the instructions or warnings can result in material damage or personal injury.
Important! The charging station must be installed, uninstalled or repaired by a licensed electrician and the installation must be executed in accordance with national and local regulations.
Important! Make sure there is no power in the cable during the installation of the device.
Important! Disregard of, or actions contrary to the safety information and instructions contained in the comprehensive manuals and printed on the device, may lead to  electric shock, fire and/or severe injury.

Special notes

| DANGER Sections marked with this symbol draw attention to electrical voltages that represent a danger to life and  limb. Actions contrary to these safety notices may lead to severe or fatal injury. Actions contrary to these safety  notices must not be carried out under any circumstances.
---|---
**| WARNING Sections marked with this symbol draw attention to additional hazards that may lead to damage to the  cable itself or to other electrical devices. Actions marked with this symbol must be carried out with special care.
|
NOTICE** Sections marked with this symbol draw attention to additional important information and special features  that are necessary for the reliable operation of the device. Actions marked with this symbol should be carried out as required.

Danger


Do not install if the outer shell has been damaged.| Do not install if the charging cable is defective or  appears cracked, broken or otherwise damaged.| Do not carry out physical repairs on the charging
station.

Main parts

Charging station
A. End cap
B. Charging unit
C. Display
D. Charging cable
E. Terminal block
F. Rotary switch
G. Wall bracket
H. Spirit level
Included
J. 2 x end cap
screws
K.1 x fixing screw
L. 4 x wall screws
M. 4 x wall plugs
Torx bit TX15

Installation planning

Requirements for the cable

  • Maximum size for the installation cable is 4 mm 2.
  • If a new cable is to be installed, apply only cable dimensions suitable for the entire circuit, including the fuse.
  • Note the maximum current (A) for the entire circuit. Consider possible additional electrical devices connected to the same fuse, for later current settings in the charging station.

Requirements for the installation site

  • Do not install the charging station in a spot where the maximum operating temperature is exceeded. See chapter Technical specification for maximum temperature.
  • Ideally, the installation site should be covered.
  • The installation site must not be in an area subject to flooding, close to water, or in areas used to store objects, or containers containing liquids.
  • The installation site must not be in explosive atmosphere areas.
  • The installation site must offer sufficient air circulation.
  • Make sure there is 55 mm of free space above the bracket so the charging unit can slide easily on and there is space for the top cover.

Tools needed

  • Installation tools for correct wiring, including stripping tool.
  • Cross recessed screwdriver for wall bracket screws.
  • Torx tool size Tx 15 with space for safety pin.

Installation

| DANGER Make sure there is no power in the cable during the installation.
---|---
**| WARNING** If the charger or charging cable is damaged, the installation should immediately be discontinued or, if the  charger is already installed, it should be taken out of operation. No additional use of the charger is permitted in this case.

  1. Turn the power/fuse off.

  2. Check that all parts and tools required for the installation are available.

  3. Guide and fix the installation cable to the spot where the charging station will be installed.
    – If necessary, find and reveal the cable inlet in the wall bracket. The cable can be inserted from the top, left, right, or bottom. Make sure that the cable is long enough.
    See image in step 6 below for details.

  4.  Place the wall bracket with a clearance of 55 mm to any obstacles above the installation area.

  5. Attach the wall bracket. Use the built-in spirit level to ensure that the wall bracket is installed at a level angle. Use the four screws delivered with the product. The holes  are made for screws with Ø4.2 mm.

  6. Remove the jacket (from A to B) with a length of 140 mm. Strip all single wires with 9-11 mm.

  7. Place the cable in the groove that points the conductor toward the hole in the upper left corner.

  8. Slide the charging unit from the top, so that all the conductors fit into the cable entry in the inner end piece. Make sure that the grooves at the top and bottom are firmly in place.

  9. Attach the fixing screw to secure the charging unit to the wall bracket.

  10. Set the maximum current rating for the charging station by turning the rotary switch to the correct position. Follow the table next to the rotary switch on the charging  unit or in the image below.

  11. Insert the conductors L, N and PE (earth) into the terminal block (see image below), and check that they are all firmly attached.
    NOTICE If the PE conductor is not isolated, add an insulation tube or electrical tape in the exposed area.

  12. Place the cable in the position shown in the image below.

  13. Note the settings from the rotary switch by marking the cell with an X below the relevant fields in the table found in the user manual, see chapter Set the required  charging level.

  14.  Attach a sticker with the set rating – max charging power – on the underside of the vehicle plug (over the existing rating label).

  15. Attach outer end cap with two screws on top of the charging unit to close the installation area.

  16. Coil charging cable around the charging unit.

  17. Turn the power/fuse on.

Testing and verification

Make sure the charging station is ready to use by checking which signals are displayed on the display before, during, and after charging the vehicle. See chapter Charge the  vehicle in the user manual.

Display view
A. Power Input Indication
B. Select Button
C. Charger Status Indication
D. Vehicle Connection Indication

Hand-over
Follow these instructions before handing over the device to the user:

  • Show which rating the installation has.
  • Demonstrate how to use the device.
  • Inform how to find further information about their device
  • Inform what to do if they experience issues with their device.
  • Hand over the user manual.

Technical specification

Item number| 712800|
---|---|---
Rated voltage| 230 VAC (1-phase, 50-60Hz)|
Rated current| 6A – 20A|
Charger type| Mode 3|
Connection to vehicle| Type 2|
RD| 30 mA AC & 6mA DC
GRID type| TN- and IT-power grid
Overheat protection| Internal sensor|
Operating temperature| -40 °C to +50 °C|
Storage temperature| -50 °C to +85 °C|
Size (I_ x W x T)| 312 x 85 x 70 mm|
Material charging unit| Aluminium|
IK rating| IK 10|
IP rating| IP 45|
Weight| 2.3 kg
Certification| CE, IEC61851, IEC62955
Recycling| WE-waste

Contact information

If you have any questions, contact your local vendor, visit defa.com or call DEFA support:
• Phone (Norway/International): +47 32 06 77 00
• Phone (Sweden/International): +46 10 498 38 00
• Phone (Finland): +358 (0)20 152 72 00
If you have any feedback on how the system or support can be improved, feel free to give us your input at connect@defa.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals