DEFA 715000 Electric Vehicle Premium Charging Station User Guide
- October 30, 2023
- DEFA
Table of Contents
715000 Electric Vehicle Premium Charging Station
User Guide
Description
DEFA Power is a premium charging station for electric vehicles and plug-in
hybrids.
The charging station has been created with the user in mind. Smart features,
simple set-up, and powerful functionality, such as full dynamic load balancing
and active phase rotation, characterizes the device. The charging station can
be installed directly onto a wall or a pole, indoors or outdoors.
- Precise load balancing: Utilizes all available power, independent of cloud connection.
- Effective cooling: No derating ensures maximal charging power.
- Active phase rotation: It utilizes power on all phases.
- Intuitive display: Information and status sharing with the user.
- Small and compact: It fits everywhere and can easily be installed and handled.
- For everyone: It can handle all power and phase needs in European markets.
- Plug and play: Easy installation, setup and configuration via app.
- Powersmart: It minimizes charging cost by utilizing spot market energy prices and planning of charging curve.
A self-test of the built-in RDC-DD will be performed in every charging start-
up cycle and every 24h.
If the built-in RDC-DD is tripped, a clear error message will be displayed on
the screen.
To reset the built-in RDC-DD, unplug the charging cable from the vehicle and
then plug it in again.![DEFA 715000 Electric Vehicle Premium Charging Station
- fig 1](https://manuals.plus/wp-content/uploads/2023/06/DEFA-715000-Electric- Vehicle-Premium-Charging-Station-fig-1.png)
Safety information
Important! Read this document before using the device. Failure to follow
any of the instructions or warnings can result in material damage or personal
injury.
Important! If the device fails to behave according to instructions,
immediately contact an electrician, responsible vendor or DEFA, see chapter
Contact information.
Important! DEFA Power must be installed, uninstalled, or repaired by a
licensed electrician. These actions must be executed in accordance with
national and local regulations.
DANGER
Sections marked with this symbol draw attention to electrical voltages that
represent a danger to life and limb. Actions contrary to these safety notices
may lead to severe or fatal injury. Actions contrary to these safety notices
must not be carried out under any circumstances.
WARNING
Sections marked with this symbol draw attention to additional hazards that may
lead to damage to the cable itself or to other electrical devices. Actions
marked with this symbol must be carried out with special care.
NOTICE
Sections marked with this symbol draw attention to additional important
information and special features that are necessary for the reliable operation
of the device. Actions marked with this symbol should be carried out as
required.
Danger
| Do not use if the outer shell has been damaged.
---|---
| Do not use the cable if it is defective or appears cracked, broken or
otherwise damaged.
| Do not use adapters or extension cords.
| Physical repairs must be executed by a licensed electrician.
| Changes to the settings or the power connections must be executed by a
licensed electrician.
Warning
| The product is designed only for Mode 3-charging of vehicles. Do not use it
for any other purpose.
---|---
| Do not allow the cable to be under strain during charging.
| Do not allow water to enter the charging port while charging.
| Keep the plug and charging station away from water. Do not expose to a
direct jet, or splashes of water.
Handling
DANGER
Ensure that the cable is never run over by a vehicle.
Handle the cable with care and do not subject it to strong force or impact. Do
not pull, twist, tangle, drag, or step on the cable or plug.
Always hold the cable by the plug
when pulling it. Do not pull the cable itself.
Sorting
See chapter Store and protect for information about how to coil the cable correctly.
- Always store the product with the cable coiled. Do not leave the cable on the ground after usage.
- Attach the plug cap to protect the vehicle plug when the product is not in use.
- Use the cable clip to coil the cable for when the product is not in use.
Main parts
A. Charging unit
B. Display
C. RFID-reader
D. Cable clip
E. Plug
F. Plug cap
G. Cable
H. Wall bracket
J. Locking tool
K. Rating label (public key)
Symbols on the display
Initialization
Open:
Charger Ready
The charger is
unlocked and ready
to use.| Locked:
Charger Ready Charger ready. Scan
the QR-code and follow the instructions
to start charging. This can only occur at
chargers that are part of a facility.| Vehicle connected (access control
enabled):
Scan QR-code/RFID Scan the QR-code or the RFID-card to start
authorization.| Authorizing
Authorization is in
progress.| Access denied
The authorization was
denied.
Charging
Preparing charging
The charging process is initialized.| Charging
The vehicle is charging.| Done or paused
The charging process is done or paused| Done
Once the cable is disconnected, a summary of the charging process is shown.
Errors and Configuration
Error:
Scan QR Scan the QR-code on
the display and follow the instructions to
troubleshoot the issue.| Error:
Contact support phone Call the displayed
number to troubleshoot. This can only occur at
chargers that are part of a facility.| Error:
Contact CPO Contact your charge
point operator to upport you.| Configuration:
Application Running The configuration
application is running.| Configuration:
Scan QR to setup Scan the QR code on
the display to initialize the setup.
Charging procedure
NOTICE Please read the charging instructions in the vehicle’s manual
before using the charging station.
WARNING The plug locks to the vehicle inlet when charging starts. The
plug stays locked until the charging procedure is finished. Always complete or
end charging in the vehicle before unplugging (refer to the vehicle’s charging
instruction for information about this).
Plug In
-
Pick up the plug, uncoil the cable, and remove the plug cap
-
Make sure that the charger is ready to be used. The Charger Ready icon should be visible on the display.
-
Insert the plug into the vehicle inlet. The following symbol should now be visible on the display to indicate that charging is initialized.
– If authorization is enabled, that process has to finish before charging can begin. See the chapter Authorization for more information. -
Make sure that charging has started. The following symbol should now be visible on the display.
NOTICE The plug must be fully inserted into the inlet of the vehicle. Failure to connect will prevent the vehicle inlet from locking the plug in place and start charging.
Unplug
WARNING Complete or stop the charging process before unplugging. To stop
charging before the vehicle is fully charged, see the vehicle’s manual.
Unlock the plug from the vehicle, refer to the vehicle’s manual for more
information.
- Remove the plug from the vehicle inlet.
- Put on the plug cap onto the plug.
- Insert the cable into the clip.
Once the charger is disconnected, the display will show a summary of the charging session.
Authorization
If authorization is needed this icon will be shown on the display:
The authorization process can be
completed by either:
- Scanning your RFID-tag on the RFID-scanner, if the charger is registered to your account in the user application.
- Opening the user application on your phone or scanning the QR code shown on the display. Follow the instructions shown on the screen.
If the authorization fails this icon will be shown on the display:
Check your user application or contact customer support of the facility.
Troubleshooting
The following symbols indicate that there has been an issue. In order to fix
the issue, scan the QR-code on the screen and follow the instructions on the
web page, or contact support.
Store and protect
Coil the cable
Roll the cable around the charging unit. Make sure that the plug hangs with
the plug cap facing the ground. Attach the clip to the cable.
Use the plug cap
The plug strap can adjust the cap’s position. This prevents the cap from
collecting water and dirt, and keeps the cap clear of the vehicle.
Maintenance and care
WARNING Do not flush water on the charging station. Do not use harsh
chemicals when cleaning.
Checking
- Keep the plug dry and check regularly for dust, dirt, pebbles, etc.
- Check the cable regularly for cracks and other damage.
Cleaning
- Use a damp cloth to clean. Do not use water or harsh chemicals.
Contact information
If you have any questions, contact your local vendor or visit
defa.com.
If you have any feedback on how the system or support can be improved, feel
free to give us your input at defa.com
Technical specification
Item number| 715000|
---|---|---
Rated voltage| 400V / 230V (1/3 phase, 50-60Hz)|
Charger type| Mode 3|
Connection to vehicle| Type 2|
RDC-DD| 6mA DC in acc. IEC 62955|
GRID type| TN/IT/TT|
Overheat protection| Internal sensor|
Operating temperature| -40 °C to +50 °C|
Storage temperature| -50 °C to +85 °C|
Size (L x W x T)| 113 x 167 x 350 mm|
Material control box| Plastic|
IK rating| IK 10|
IP rating| IP 55 (Wallbracket IP44)|
Weight| 5.0 kg|
Certification| CE, IEC61851, IEC62955|
Recycling| EE-waste|
****defa.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>