COMMAND ACCESS TECHNOLOGIES PD10-M-RIM PTS Instruction Manual

June 3, 2024
COMMAND ACCESS TECHNOLOGIES

COMMAND ACCESS TECHNOLOGIES PD10-M-RIM PTS

COMMAND-ACCESS-TECHNOLOGIES-PD10-M-RI-product-image

INSERT Instructions

The PD10-M-RIM is a storefront grade 1 exit device equipped with motor
drive latch retraction. Retrofits Doromatic 1790 & First Choice 3790 .COMMAND-ACCESS-TECHNOLOGIES-PD10-M-RI-1

KIT INCLUDES

  • A. Head Cover pack
  • B. RIM Exit Device
  • C. Hinge Stile End Cap pack
  • D. Lock Stile End Cap pack
  • E. Rim Strike pack
  • F. MOTOR KIT – Installed in exit device
  • G. 1- 50944 Molex Pigtail
  • H. 1- 50030 8’ Lead w/ VD Connector

TOOLS REQUIRED

  • Cordless Drill
  • Needle nose Pliers
  • Measuring Tape
  • 1/2 Drill bit

Technical Information

COMMAND-ACCESS-TECHNOLOGIES-PD10-M-RI-2

Setting PUSH TO SET (PTS)

Important Info
Make sure to set PTS before finishing installation

  • Step 1 – To enter PTS mode: Depress MM5 button & apply power. The device will emit 1 SHORT beep. The device is now in PTS mode.
  • Step 2 – While depressing the push pad, apply power. (i.e. presenting the credential to the reader).
  • Step 3 – Continue to keep pad depressed, the device will emit 1 LONG Beep. After the beep has stopped, release the pad and now the adjustment is complete. test the new location, If not to your liking repeat the 3 steps.

Troubleshooting & Diagnostics

Beeps Explanation Solution
2 Beeps Over Voltage > 30V unit will shut down. Check voltage &

adjust to 24 V.
3 Beeps| Under Voltage| < 20V unit will shut down. Check voltage & adjust to 24 V.
4 Beeps| Failed Sensor| Verify all 3 sensor wires are installed correctly. Replace sensor if problem persists by contacting office.
5 Beeps| Retraction or dogging failure| After 1st fail: 5 beeps then immediately attempts to retract again.
After 2nd fail: 5 beeps with pause in-between for 30 seconds then device attempts to retract again.
After 3rd fail: 5 beeps every 7 minutes, device will not attempt to retract.
To Reset: Depress bar for 5 seconds at any time.

Electrified Exit Device

INSTALLATION EXAMPLE

COMMAND-ACCESS-TECHNOLOGIES-PD10-M-RI-4

RIM PANIC

Installation Template
All prep is shown on interior side of the door, except where noted. Right hand door shown. (LHR)COMMAND-ACCESS-TECHNOLOGIES-
PD10-M-RI-5

STEP 1 – Mount Exit Device

  • Install the stile mounting bracket with 2 ea. 1/4-20 x 1/2 pan head screws. Leave space to capture the base of the device. (See next slide)

  • Slide the end of baserail underneath the mounting bracket.

Optional STEP – Installing Cylinder
  • A. Install trim cylinder tail piece so that it is slightly below the face after mounting. Install key cylinder using mounting screws supplied with cylinder. (Screws may need to be shortened.)

  • For Night Latch, leave set screw in place.

  • Hold Back function is desired, remove the set screw to allow additional rotation of cylinder tailpiece.

STEP 1B – Continued

  • Attach head of device to stile with 2 ea. 1/4-20 x 3/4 “ screws. Tighten screws on the head and base of the device.

STEP 2 – Drill Wire Chase

  • Remove lock stile end cap.

  • Slide push pad off of baserail.

  • Drill the hole for our 2 pin power lead in-between the 2 mounting screws.

  • Feed the 2 pin power lead into the hole and connect to our MM4 module. Also, make sure to clean out any debris left.
    Note: Depending on where your power transfer is; next you would fish the other side of the power lead we connected to the MM4 and hook up to your incoming power. If you have a portable tester this would be a good time to test fire the motor.

  • Replace push pad, making sure the activating brackets and pins slide through the 3rd channel.

  • F. Reinstall the lock stile end cap.

STEP 3 – Install Head & End Cap

  • A. Install head cover with 2 ea. 10-32 x 3/8 screws.

  • Install hinge stile push pad cover with 2 ea. 8-32 x 1 1/2” screws. Now you set you latch retraction adjustment with our “PTS” technology.
    See page #2

STEP 4 – Install Door Frame Stop

  • Install the roller strike with 2ea. #10-32 x 1 “ screws so the roller is flush with the frame stop. (Use strike shim for 5/16” stops.)

  • Using the roller strike as a template, drill and tap rear mounting holes. Install remaining 10-32 x 1” mounting screws and tighten all screws.

STEP 5 – Install Wear Strip

  • Cut wear strip to desired length.
  • Clean surface of the frame before. apply wear strip in indicated area.
  • Peel backer paper from wear strip.
  • Apply wear strip flush to front of frame jamb in indicated area.

COMMAND-ACCESS-TECHNOLOGIES-PD10-M-RI-21

PD10 Parts Breakdown

COMMAND-ACCESS-TECHNOLOGIES-PD10-M-RI-23

COMMAND-ACCESS-TECHNOLOGIES-PD10-M-RI-25

US CUSTOMER SUPPORT1-888-622-2377 | WWW.COMMANDACCESS.COM | CA CUSTOMER SUPPORT 1-855-823-3002

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals