Husqvarna 320 NERA Lawn Automower User Guide

Husqvarna 320 NERA Lawn Automower

This Quick Guide gives you information about how to install your robotic lawn mower with a wire installation. If you install your product with EPOS™ technology without boundary wire, read the Operator’s manual supplied with the EPOS Plug-in Kit.

To start the product for the first time

1. Download the Automower® Connect app from AppStore or Google Play.
2. Sign up and specify an e-mail address and a password to create a Husqvarna account.
3. Log in to your Husqvarna account in the app.
4. Push the jog wheel for 3 seconds to switch on the robotic lawn mower.
5. Enter the factory PIN code on the robotic lawn mower.
6. Select My mowers in the Automower® Connect app, and then select the plus sign (+).
7. Follow the instructions in the app.

Placement of and connecting the charging station

1. Place the charging station at a central position in the work area, with a lot of open space in front of the charging station and on a relatively horizontal surface.
2. Attach the top of the charging station.
3. Put the grommet with the cables into position.
4. Connect the cable to the charging station.
5. Connect the power supply’s low-voltage cable to the charging station and the power supply.
6. Connect the power supply to a 100-240 V wall socket.
7. Place the robotic lawn mower in the charging station to charge the battery while the boundary wire is laid.

Placement of the boundary wire and the guide wire

1. . Lay the boundary wire so that it forms a loop around the working area.
2. Make an eyelet at the point where the guide wire will later be connected.
3. Run the guide wire to the point on the boundary loop where the connection will be made. Avoid laying the wire at tight angles

Connecting the boundary wire and the guide wire

1. Narrow passages in the yard make it difficult for the robotic lawn mower to find the charging station. The robotic lawn mower can be lead to remote areas using the guide wire. The guide wire also helps the robotic lawn mower to quickly find the charging station.
2. Lay the guide wire under the charging station and at least 2 m / 7 ft straight out from the front edge of the charging station.
3. Open the connectors and lay the wire ends in the recesses on each connector.
4. Press the connectors together using a pair of pliers.
5. Cut off any surplus boundary wire. Cut 1-2 cm / 0.4-0.8” above the connectors.
6. Press the connectors onto the contact pins, marked AL (left) and AR (right), on the charging station. It is important that the right-hand wire is connected to the right-hand contact pin, and the left-hand wire to the left-hand pin.
7. Fasten the connector to the contact pin marked G1/G2/G3 on the charging station.

Connecting the guide wire to the boundary wire

1. Cut the boundary wire with a wire cutters at the centre of the eyelet that was made in step C.2.
2. Connect the guide wire to the boundary wire using the accompanying couplers. Press the couplers completely together with a polygrip

Maintenance

• Set the product to OFF before all work on the robotic lawn mower’s chassis, such as cleaning or replacing the blades. Replace the blades regularly for the best mowing result.
• Never use a high-pressure washer to clean the robotic lawn mower. Never use solvents for cleaning. Clean the product with a brush.
• All connections to the charging station (power supply, boundary and guide wire) must be disconnected if there is a risk of a thunderstorm.
• Fully charge the battery at the end of the season before winter storage.

For more information and instructions, read the complete Operator’s manual in the Automower® Connect app or onwww.husqvarna.com.

Green solid light
Good boundary loop signal.

Green flashing light
ECO mode is activated.

Blue flashing light
Malfunction in the boundary loop

Red flashing light
Malfunction in the charging station’s antenna.

Red solid light
Fault in the circuit board or incorrect power supply in the charging station. The fault should be rectified by an authorized service technician.

Automower® Connect

|
---|---

Ⓐ

Automower Connect® lets you remote control your Automower® and change its settings and schedules from wherever you are. You can keep track of its movements in the map view, check its current status and receive notifications if something happens.

EPOS™ Plug-in Kit

For installation without boundary wire purchase the EPOS™ plug-in kit separately. It is a flexible installation with virtual boundaries that are created in the Automower® connect app. EPOS plug-in kit includes a reference station and a EPOS plug-in to install on you robotic lawn mower.

AUTOMOWER® IS A TRADEMARK OWNED BY HUSQVARNA AB. COPYRIGHT © 2023 HUSQVARNA. ALL RIGHTS RESERVED.

www.husqvarna.com

References

• Husqvarna Forest & Garden

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>