metabo D 10VH2 Drill Instruction Manual

metabo D 10VH2 Drill Instruction Manual

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or maintaining this power tool.
Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs,and by observing appropriate safety procedures.
Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which contain the operation and maintenance instructions.
Hazards that must be avoided to prevent bodily injury or machine damage are identifi ed by WARNINGS on the power tool and in this Instruction Manual.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.
CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or may cause machine damage.
NOTE emphasizes essential information

SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

[](https://manuals.plus/wp-content/uploads/2022/12/metabo-D-10VH2-Drill-

Instruction-Manual_3.jpg)WARNING

Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

SAFETY

1. Work area safety a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
   b) Do not operate power tools in explosive atmospheres, such as in the presence of
   fl ammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
   c) Keep children and bystanders away while operating a power tool.
   Distractions can cause you to lose control.

2. Electrical safety
   a) Power tool plugs must match the outlet. Never modify the plug in any way.
   Do not use any adapter plugs with earthed(grounded) power tools.
   Unmodified plugs and matching outlets will reduce risk of electric shock.
   b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators.
   There is an increased risk of electric shock if your body is earthed or grounded.
   c) Do not expose power tools to rain or wet conditions.
   Water entering a power tool will increase the risk of electric shock.
   d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.
   Keep cord away from heat, oil, sharp edges or moving parts.
   Damaged or entangled cords increase the riskof electric shock.
   e) When operating a power tool outdoors, use an extension cord suitable for outdoor use.
   Use of a cord suitable for outdoor use reduces the risk of electric shock.
   f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3. Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool.
   Do not use a power tool while you are tired or under the infl uence of drugs, alcohol or medication.
   A moment of inattention while operating power
   tools may result in serious personal injury.
   b) Use personal protective equipment. Always wear eye protection.
   Protective equipment such as dust mask, nonskid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
   c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool.
   Carrying power tools with your fi nger on the switch or energising power tools that have the switch on invites accidents.
   d) Remove any adjusting key or wrench before turning the power tool on.
   A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
   e) Do not overreach. Keep proper footing and balance at all times.
   This enables better control of the power tool in unexpected situations.
   f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
   g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
   Use of dust collection can reduce dust-related hazards.
4. Power tool use and care
   a) Do not force the power tool. Use the correct power tool for your application.
   The correct power tool will do the job better and safer at the rate for which it was designed.
   b) Do not use the power tool if the switch does not turn it on and off . Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
   c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
   d) Store idle power tools out of the reach of children and do not allow persons unfamiliar  with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
   e) Mai n tai n power tools . Check for misalignment or binding of moving parts, breakage of parts and any other condition that may aff ect the power tool’s operation.
   If damaged, have the power tool repaired before use.
   Many accidents are caused by poorly maintained power tools.
   f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
   g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.
   Use of the power tool for operations diff erent from those intended could result in a hazardous situation.
5. Service
   a) Have your power tool serviced by a qualifi ed repair person using only identical replacement parts.
   This will ensure that the safety of the power tool is maintained.

SPECIFIC SAFETY RULES AND SYMBOLS __

1. Use auxiliary handle(s), if supplied with the
   Loss of control can cause personal injury.

2. Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

3. ALWAYS wear ear plugs when using the tool for extended periods.

Prolonged exposure to high intensity noise can cause hearing loss.

4. NEVER touch the tool bit with bare hands after
5. NEVER wear gloves made of stuff liable to roll up such as cotton, wool, cloth or string,
6. ALWAYS securely grip the

7.  NEVER touch moving parts.

NEVER place your hands, fingers or other body parts near the tool’s moving parts.

8. NEVER operate without all guards in NEVER operate this tool without all guards or safety features in place and in proper working order. If maintenance or servicing requires the removal of a guard or safety feature, be sure to replace the guard or safety feature before resuming operation of the tool.

9.   Use right tool.

Don’t force small tool or attachment to do the job of a heavy-duty tool.
Don’t use tool for purpose not intended —for example— don’t use circular saw for cutting tree limbs or logs.

10. NEVER use a power tool for applications other than those specified.

NEVER use a power tool for applications other than those specified in the Instruction Manual.

11. Handle tool correctly.

Operate the tool according to the instructions provided herein. Do not

drop or throw the tool. NEVER allow the tool to be operated by children, individuals unfamiliar with its operation or unauthorized personnel.

12. Keep all screws, bolts and covers tightly in Keep all screws, bolts, and plates tightly mounted. Check their condition periodically.

13. Do not use power tools if the plastic housing or handle is

cracked.

Cracks in the tool’s housing or handle can lead to electric shock. Such tools should not be used until repaired.

14. Blades and accessories must be securely mounted to the tool.

Prevent potential injuries to yourself or others. Blades, cutting implements and accessories which have been mounted to the tool should be secure and tight.

15.  Keep motor air vent clean.

The tool’s motor air vent must be kept clean so that air can freely flow at all times. Check for dust build-up frequently.

16. Operate power tools at the rated Operate the power tool at voltages specified on its nameplate.

If using the power tool at a higher voltage than the rated voltage, it will result in abnormally fast motor revolution and may damage the unit and the motor may burn out.

17.  NEVER use a tool which is defective or operating abnormally.

If the tool appears to be operating unusually, making strange noises, or otherwise appears defective, stop using it immediately and arrange for repairs by a metabo HPT authorized service center.

18. NEVER leave tool running unattended. Turn power off.

Don’t leave tool until it comes to a complete stop.

19.   Carefully handle power tools.

Should a power tool be dropped or struck against hard materials inadvertently, it may be deformed, cracked, or damaged.

20.   Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may damage and crack plastic parts. Do not wipe them with such solvents. Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry thoroughly.

21. ALWAYS wear eye protection that meets the requirement of the latest revision of ANSI Standard 1.
    

22. ALWAYS be careful with buried object such as an underground

Touching these active wiring or electric cable with this tool, you may receive an electric shock.
Confirm if there are any buried object such as electric cable within the wall, floor or ceiling where you are going tos operate here after.

23.   Definitions for symbols used on this tool

V……………. volts Hz      hertz
A……………. amperes
no…………… no load speed
W…………… watt ………………Class II Construction–/min  revolutions per minute

DOUBLE INSULATION FOR SAFER OPERATION __

To ensure safer operation of this power tool, metabo HPT has adopted a double insulation design. “Double insulation” means that two physically separated insulation systems have been used to insulate the electrically conductive materials connected to the power supply from the outer frame handled by the operator. Therefore, either the symbol “ ” or the words “Double insulation” appear on the power tool or on the nameplate.
Although this system has no external grounding, you must still follow the normal electrical safety precautions given in this Instruction Manual, including not using the power tool in wet environments.

To keep the double insulation system effective, follow these precautions:

• Only metabo HPT AUTHORIZED SERVICE CENTER should disassemble or assemble this power tool, and only genuine metabo HPT replacement parts should be
• Clean the exterior of the power tool only with a soft cloth moistened with soapy water, and dry Never use solvents, gasoline or thinners on plastic components; otherwise the plastic may dissolve.

FUNCTIONAL DESCRIPTION

NOTE

The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool.
NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safety instructions contained in this manual.Some illustrations in this Instruction Manual may
show details or attachments that differ from those on your own power tool

NAME OF PARTS

SPECIFICATIONS

ASSEMBLY AND OPERATION

APPLICATIONS __

• Boring holes in metal, wood and

PRIOR TO OPERATION __

1. Power source
   Ensure that the power source to be utilized conforms to the power source requirements specified on the product nameplate.

2. Power switch  Ensure that the switch is in the OFF position. If the plug is connected to a receptacle while the switch is in the ON position, the power tool will start operating immediately and can cause serious injury.

3. Extension cord When the work area is far away from the power source, use an extension cord of sufficient thickness and rated capacity. The extension cord should be kept as short as practicable.

WARNING

Damaged cord must be replaced or repaired.

4. Check the receptacle
   If the receptacle only loosely accepts the plug, the receptacle must be repaired. Contact a licensed electrician to make appropriate repairs.
   If such a faulty receptacle is used, it may cause overheating, resulting in a serious hazard.

5. Check your work environment: Confirm that the work site is placed under appropriate conditions conforming to prescribed precautions.Selecting the appropriate drill bit:

6. • When boring woodWhen boring metal or plastic Use an ordinary metalworking drill bit. Use an ordinary woodworking drill bit.

However, when drilling 1/4″ (6.5 mm) or smaller holes, use a metalworking drill bit.

7. Mounting and dismounting of the bit (Fig. 2)
   Open the chuck jaws, and insert the bit into the chuck. To open the chuck jaws, hold the ring while turning the sleeve in the counterclockwise direction (viewed from the front side).

8. Firmly grasp the ring and turn the sleeve in the clockwise Tighten securely.

9. To remove the bit, firmly grasp the ring and turn the sleeve in the counterclockwise
   

10. If it is hard to loosen the sleeve, fix the spindle using the open-end wrench, hold the sleeve firmly, and turn it in the loosening direction (counterclockwise when viewed from the front). (Fig. 3)
    

11. Check the rotational direction (Fig. 4)

The bit rotates clockwise (viewed from the rear side) by pushing the R-side of the push button.
The L-side of the push button is pushed to turn the bit counterclockwise.
(The     and       marks are provided on the body.

To install the side handle, thread it into the M10 hole on the desired side of the gear cover and tighten it securely.
Installing the side handle (Optional accessory) (Fig. 5) A Side handle can be installed on either side of the tool for right or left handed

8. Attaching the (Optional accessory)

| For hook (side-attaching)

(Fig. 6)Fix the hook firmly on the desired side of the gear cover using M10 bolt which is supplied with hook.

CAUTION

When the power tool is used with a hook fixed to it, pay attention to the following points:

• Before hanging the main unit from the waist belt, make sure that the drill has come to a complete
  While it is suspended from the waist belt, the power plug must be disconnected from the power source.

• In the case of operation in a high place, it is dangerous to drop the tool accidentally. If the hook is deformed or hung from the wrong position, there is danger that the hook will slip off and the tool will fall. Be careful to avoid danger.

• In making a through hole, the power tool sometimes shakes violently when the workpiece is pierced, from example. Be careful you are not hurt by the hook even if such situation happens.

HOW TO USE CAUTION

To prevent accidents, make sure to turn the switch off and disconnect

the plug from the receptacle
when the drill bits and other various parts are installed or removed. The power switch should also be turned o ff during a work break and after work.

1. Switch operation

• When the trigger switch is depressed, the tool When the trigger is released, the tool stops.
• The rotational speed of the drill can be controlled by varying the amount that the Trigger switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as the trigger switch is pulled
• The desired rotation speed can be pre-selected with the speed control

Turn the speed control dial clockwise for higher speed and counterclockwise for lower speed. (Fig. 7)

MAINTENANCE AND INSPECTION

WARNING: Be sure to switch power OFF and disconnect the plug from the

receptacle during maintenance and inspection.

1. Inspecting the drill bits
   Since use of a dull tool will cause motor malfunctioning and degraded efficiency, replace the drill bit with a new one or resharpening without delay when abrasion is noted.

2. Inspecting the screws

Regularly inspect all screws and ensure that they are fully tightened. Should any of the screws be loosened, retighten them immediately.

WARNING: Using this drill with loosened screws is extremely dangerous.

3. Keeping after use
   When not in use, the Power tool should be kept in a dry place out of the reach of children.

4. Inspecting the carbon brushes
   For your continued safety and electrical shock protection, carbon brush inspection and replacement on this tool should ONLY be performed by a metabo HPT AUTHORIZED SERVICE CENTER.

5. Maintenance of the motor
   The motor unit winding is the very “heart” of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water.

6. Service and repairs
   All quality power tools will eventually require servicing or replacement of parts because of wear from normal use. To assure that only authorized replacement parts will be used, all service and repairs must be performed by a metabo HPT AUTHORIZED SERVICE CENTER, ONLY.Service parts list

CAUTION

Repair, modification and inspection of metabo HPT Power Tools must be carried out by an metabo HPT Authorized Service Center.
This Parts List will be helpful if presented with the tool to the metabo HPT Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed.

MODIFICATIONS

metabo HPT Power Tools are constantly being improved and modified to incorporate the latest technological advancements.
Accordingly, some parts (i.e. code numbers and/or design) may be changed without prior notice.

ACCESSORIES

WARNING: ALWAYS

use Only authorized metabo HPT replacement parts and accessories. Never use replacement parts or accessories which are not intended for use with this tool. Contact metabo HPT if you are not sure whether it is safe to use a particular replacement part or accessory with your tool. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage.

NOTE

Accessories are subject to change without any obligation on the part of the metabo HPT.
OPTIONAL ACCESSORIES.. sold separately

• Side handle (Code 981205)
• Hook (Code 982593)

NOTE

Specifications are subject to change without any obligation on the part of the metabo HPT.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>