origin SF-028 AI DC Stand Fan Instruction Manual

origin SF-028 AI DC Stand Fan

Important Safety Information

• Read all instructions carefully before using the Fan.
• Use this Fan only as described in this manual. Any other use not recommended by the manufacturer may casue fire, electrical shock or injury to persons.
• Open the package and ensure that the Fan is undamaged. In case of doubt do not use the FAN Cooler and contact your supplier.
• Do not let children play parts of package.
• Before using the Fan, check if the voltage marked on the rating labelcorresponds to the mains at your home.

AI DC Stand Fan

• Avoid using extension cord as it may overheat and casue fire.

• Do not pull the power cord to disconnect from power source. Always grasp the plug to pull out.

Important safety informaion

• Do not inseort anv objects into the fan as n may cause an eleuric shock o,d3mage. Do not block or tamper with the Fan tn any manner while tt 1s 1n 0-peradon.
• Do not leave the Fan unattended Always unplug the Fan Cooler when not 1n use.
• WARNING The On. Off switch should not be used as the sole means of d1sconne-ct1ng power. Always unplug lhe power cord before setvtCJng ormoving lhe unit.
• This Fan 1s ,mended for household use ONL V and not for industrial or outdoor use
• Always dlSConnected the fan flam thepower supp{y when moving it from one loc.alJon to another .
• gnus product contains recydable f+- matenals. Do not d ispose this – product as unsorted muruclpal waste. Please contact your Jocaf munmpahty for the nearest collection

AI dc stand fan

• The Fan ts not 1n1er.ded fOf use in ·wetor damp locat10M. “‘le\let loc.a,e the Fa” where 1t may ran ono a bathtub 0< other water container.

• Do r,oi place the Fan near a soorce of heat or fue

• l(eep the Fan ch!a.n 10 ma1nt..in In good cond1t1on (refer to maintenance secc,on}.

• WARNING· To avoid danger of elect11c shock. unplug from ootiet when no, 1n use and before deamng. If the power cord 1s damaged. 11 must be replaced by the manufacturer. its .service agent or s1nu.larly quaJ,fied persons 1n order to avoid hazard.

Assembly

1. Front Guard
2. Blade Cap
3. Blade
4. Guard Cap
5. Rear Guard
6. Main Body
7. Outer Pole
8. Base Connector
9. Base
10.  Wire Cover
11. Connected Sockets and Plugs
12. Power Cord
13. Base Cap
14. Remote
15. Screw
16. Remote Storage Place

The picture is for reference only, everything in kind shall prevail.

Function Setting

The Fan may be operated by the control panel located on the top of the Fan

1. Place the Fan on a stable and flat surface. Plug the Power Cord into an a.c. 220-240V electrical outlet.

2.  POWER: Turn the Fan ON by pressing the On/Off key” “, the Fan will start at speed 1
   

3. . SPEED: Adjust the Fan speed to the desired level: 8 level wind speed by pressing
   Speed key . The LED light of speed will be on and indicate the speed level:
   Speed 1 : First LED light one half light on
   Speed 2 : First LED light light on
   Speed 3 : First LED light light on and second LED light one half light on
   Speed 4 : First LED light and second LED light light on
   Speed 5: Two LED light light on and third LED light one half light on
   Speed 6 : Three LED light light on
   Speed 7 : Three LED light light on and fourth LED light one half light on
   Speed 8 : All the LED light light on

4. . OSC: Press the OSC key” ” to allow the Fan to oscillate the wind direction. To stop the oscillation, press the key again.

Remote Control

1. All functions performed by the Remote Control work are different to the Manual.
2. Install battery: Install three  batteries.
   (Caution: Do not mix new and used, carbon/alkaline or different brands of batteries.)

WARNING

1. Keep batteries out of reach of children. Should a child swallow a battery, consult a doctor immediately.
2. Do not recharge or dispose in fire.
3. Keep in a dry and cool place.
4. Insert battery in rigdt direction.
   Battery disposal – Please dispose the used battery per municipal or provincial law

Pairing the remote to the Fan

1. Power on the Fan, press the On/Off key” ” on remote, the LED will show and flash as ” “. Press the Mode key” ” and hold for 3 seconds, the LED will show and flash as ”  “,and four wind speed indicators will light up on the Fan. Then press any key on the Fan within 5 seconds, will hear a “ Bi ” sound, the four wind speed indicators will off, and the LED display will show the room temperature, which means the pairing is successful .
2. After pairing, the Fan can operate by remote with LED display  accordingly.
3. If the pairing is not successful, the LED display will show ”  ” and will go out if no operation within 5 seconds.
4. After the battery is replaced, the remote control needs to be paired again with the Fan before using.

Remote Control

1. Place the Fan on a stable and flat surface. Plug the Power Cord into an a.c. 220-240V electrical outlet.

2. POWER: Turn the Fan ON by pressing the On/Off key” “, the Fan will start at speed 1
   

3. SPEED: Adjust the Fan speed to the desired level: 8 level wind speed by pressing the Speed key” “. The LED display will show the wind speed.

4. OSC: Press the OSC key” ” to set desired angle (30/60/90/120 ), allow the Fan to LEFT/RIGHT oscillate the wind direction. To stop the oscillation, press the key four time

5. MODE: Press the Mode key”  ” to set the Fan as Auto, or Sleep mode. The mode is displayed on the LED display. Press the key 3rd time, it will come back to normal mode and the LED indicator of wind mode will be off
   Auto Mode(AUTO) :
   ● When the room temperature is below 25℃,the Fan will work as speed 1 for 15 seconds, then speed 2 for 15 seconds, then return to speed 1 for 15 seconds… (as cycle).
   ● When the room temperature is between 25℃ and 28℃, the Fan will work as speed 3 for 15 seconds, then speed 4 for 15 seconds, then return to speed 3 for 15 seconds…(as cycle).
   ● When the room temperature is between 29℃ and 34℃, the Fan will work as speed 5 for 15 seconds, then speed 6 for 15 seconds, then return to speed 5 for 15 seconds…(as cycle).
   ● When the room temperature is above 34℃ the Fan will work as speed 7 for 15 seconds, then speed 8 for 15 seconds, then return to speed 7 for 15 seconds…

6. . TIMER: Pressing the Timer key” ” to set desired auto power off time, There are 12 time intervals, from 1-hour to 12-hour, and displayed on the LED display.

Maintenance

WARNING: ALWAYS UNPLUG THE POWER CORD BEFORE MOVING OR SERVICING. DO NOT IMMERSE THE FAN IN WATER! BEFORE CLEANING, MAKE SURE THAT THE UNIT HAS BEEN SWITCHED OFF AND IT IS UNPLUGGED FROM THE MAIN OUTLET.
Housing & Guard: Clean the outside of the Fan with a soft cloth, to remove persistent dirt or grime wipe down with a cloth that has been dampened with warm soapy water.
Blade: Loose the screw and pull the front guard out. Clean the blade with a soft damp cloth, place back and fix the front guard with the screw after cleaning .
CAUTION: Do NOT use gasoline, benzene, thinner, harsh cleaners, etc., as they will damage the Fan. NEVER use ALCOHOL or any other SOLVENTS.
STORAGE: Store the Fan with these instructions in the original box in a cool and dry place.

Specification

Origin Map

Warranty Card

Item : AI DC Stand Fan
Model : SF-028

This product is warranted for 1year (commercial use for 3 months) from the date of purchase under the following conditions:

1. For any defect, in the judgment of our technician, if it is caused under normal use, we are responsible for repairing the product, and/or replacing parts at free of charge.

2. This warranty DOES NOT apply to:
   ● If the product has been damaged through abuse, misuse, negligence or accidents;
   ● Unauthorized repair, alteration/modification;
   ● Any damage or scratch on the housing, front and rear guard, blade, remote or accessories.

3. The customer is requested to bring the unit to and from our Service Centre whenever service is needed.

4. Any defective parts, which had been replaced, shall be of our property.

5. This warranty is valid in H.K.S.A.R. only.

6. Please show the Invoice to get free service.
   ● Extra 3 months warranty: just complete Online Warranty Registration within 10 days from the date of receipt, free warranty will be extended to 15 months (not applicable to commercial use). Please enter our website: www.origo.hk

Service Centre
ORIGIN MARKETING LIMITED
Unit H, 21/F., Reason Group Tower (nearby 12 Wah Sing Street), 403 Castle Peak Road,
Kwai Chung, N.T., Hong Kong.
Tel: 2156 8238
www.origo.hk

References

• ORIGIN

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>