ORIGIN D50-8 Director In Ceiling Loud speaker Installation Guide
- June 1, 2024
- origin
Table of Contents
ORIGIN D50-8 Director In Ceiling Loud speaker
Specifications
- Product Name: DIRECTOR COLLECTION DIRECTOR D50-8 LOUDSPEAKER
- Cutout Diameter: 5 7/8” (150mm)
- Speaker Diameter: 6 3/4” (172mm)
- Mounting Depth: 3 1/2” (90mm)
- Grille Diameter: 7 3/16” (182mm)
- Grille Depth: 3/16” (5mm)
Product Usage Instructions:
Quick Start Guide
The Speaker will arrive securely in its Bayonet Ring. Scan the QR Code on
the reverse of this page for full instructions for thisproduct.
Removal of Speaker from Bayonet Ring
- PULL THE METAL LOCK TAB AWAY from the Bayonet Ring before removing the loudspeaker.
- With one hand on the ring & one hand on the speaker, TURN COUNTER-CLOCKWISE to release the speaker from the Bayonet Ring.
Speaker Installation
- PUSH Rails Inwards and INSERT THE BAYONET RING INTO THE CUT-OUT hole within the ceiling surface
- PUSH Tabs AGAINST RAIL through Ceiling Hole and lower them along the Bayonet rails.
- Lift Speaker and TWIST CLOCKWISE to LOCK Into Bayonet Ring.
FAQ
-
Q: How do I adjust or remove the Bayonet Zip-Clips?
A: If the Bayonet Zip-Clips need to be adjusted or removed, depress the metal tabs along the rail and push up. -
Q: Why is it important to ensure the Lock Tab is properly engaged?
A: The grille may not sit flush until this Lock is properly engaged, ensuring a secure installation.
DIRECTOR COLLECTION
DIRECTOR D50-8 LOUDSPEAKER
- 5 1/4” (133mm) Poly/Rubber Woofer
- 1” (25mm) Silk Pivoting Tweeter
- Butyl Rubber X-Wave™ Surround
- Tool-less Mounting Installation
SPECIFICATIONS
- PRODUCT NAME D50-8
- Cutout Diameter 5 7/8” (150mm)
- Speaker Diameter 6 3/4” (172mm)
- Mounting Depth 3 1/2 (90mm)
- Grille Diameter 7 3/16” (182mm)
- Grille Depth 3/16” (5mm)
Please visit docs.originacoustics.com or scan this QR code using your smart device for the most up to date safety information and use instructions for this product.
*All warranties and warranty conditions are subject to change. Please refer to docs.originacoustics.com for the latest information.
The Speaker will arrive securely in its Bayonet Ring. Scan the QR Code on the
reverse of this page for full instructions for this product.
REMOVAL OF SPEAKER FROM BAYONET RING
- OPEN POSITION: PULL THE METAL LOCK TAB AWAY from the Bayonet Ring, before removing loudspeaker from Bayonet Ring.
- With one hand on the ring & one hand on the speaker, ONE QUARTER TURN COUNTER-CLOCKWISE will release the Speaker from the Bayonet Ring.
SPEAKER INSTALLATION
- Push the Zip-Clip™ rails inwards, just enough from the top, so they fit through the ceiling hole opening, then INSERT THE BAYONET RING INTO THE CUT-OUT hole within the ceiling surface.
- Reach through and PLACE 2 FINGERS ON THE GROOVES of the Bayonet Zip-ClipTM to pull each Zip-ClipTM down the rail.
- PULL DOWN on all 4 Bayonet Zip-ClipsTM to lower them along the Bayonet rails.
Note : If the Bayonet Zip-ClipsTM need to be adjusted or removed, depress the metal tabs along the rail and push up. - After connecting wires, insert the Speaker into the Bayonet Ring, with the METAL LOCK TAB LIFTED AWAY FROM THE RING.
- TWIST THE SPEAKER 15 O CLOCKWISE, until the indicators on both the Bayonet Ring & the Speaker are aligned.
- CLOSED POSITION: To finalize the installation, PUSH THE METAL LOCK TAB TOWARDS the Bayonet Ring.
Note : Grille may not sit flush until this Lock is properly engaged.
11-30-23
6975 S Decatur Blvd, Las Vegas, NV 89118 •
www.originacoustics.com •
844-674-4461
©2023 Origin Acoustics. All copyrighted, trademarked and patented elements
mentioned herein are the sole property of Origin Acoustics.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>